Filter Results By:
Products
Applications
Manufacturers
-
product
Audio Test Tone Generator
Tone Plug
The TONE PLUG offers five user selectable sine wave test tones at frequencies of 100, 250, 400, 1K and 10KHz. An additional 5 special function test signals are also provided.
-
product
NEXTest 7
PK-2030/2032/2033/2036/2037/2038
NEXTest 7 is an advanced and unique tester in the market. It's designed to check and troubleshoot the pin connections of Display port & HDMI prior to installation on equipment. By using advanced technology to verify the integrity (20 pins + shield) of both display port and HDMI cables, especially for HDTV installation and DIY termination in the field, solving your cable testing need, unlink all of the other testers verify 9 circuits only. It checks for opens, shorts, miswires and intermittent faults in all conductors plus shield continuity, most tester only test for opens. It displays cable map results of both TX (near end) and RX (far end) on the main unit, either on testing before or after installation cables. User can easily read and determine the actual 21 pins configuration on main unit. It employs both auto and manual scanning of 21 wires. Tone Generator mode transmits two selectable tones on each pin for use with Net Probe (PR-06P) optional, enables one to quickly locate a cable. It's capable of testing up to 8 cables and locations at one time. NEXTest 7 especially features a self-learning mode to memorize cable pin out for testing large quantity standard or custom cables for PASS/FAIL a snap, makes testing quick and more efficient.
-
product
Cable Fault Locator
TX2002
Lowest Cost Full Specification Professional Graphical TDR Rugged Palm Top Design 350g (12oz) 5 Measurement Ranges up to 3500m (11,500ft) 50, 75 & 100 ohm Selectable Cable Impedance Built in Tone Generator for Pair Tracing & Identification Suitable for testing all Communications Cables Water & Dust Proof to IP54 Complete with tool-belt holster & test leads
-
product
Mixed Mode Testing
The Mixed Mode add-on modules for the Random Vibration Control Software allow tests to run with sine tones and/or narrowband random signals superimposed on a random background. Mixed mode testing is a complex control task, and m+p VibControl supports three modes: Sine-on-Random (SoR), Random-on-Random (RoR) and Sine-on-Random-on-Random (SoRoR). Gunfire burst control can also be superimposed in each case.
-
product
MultiTracker
PK-108/108A
The Multitracker provides the most powerful combination of a high power Net toner, cable and network testers in one unit. It generates 2 selectable net tones with the capability to quickly locate and identify active network cables connected at HUB, Switch or Router, and live phone line systems. It also features a pin-by-pin cable testing with an auto scan and step modes for checking detail VDV (voice, data and video) cables pin-out configuration. Network test includes detecting PoE, Ethernet and Telephone services.
-
product
NTSC PATTERN GENERATOR
PG-38
Model PG-38 NTSC Pattern Generator can be use to quickly and easily troubleshoot, test, and align NTSC television. Features a wide selection of popular video patterns including Color Bars, Crosshatch, Dot, Staircase, Circle, Center Cross, Window, and Raster for accurate and comprehensive TV troubleshooting and testing. Supports both progressive and interlace scanning system. Composite video and S-Video output. RF video output on Channel 3 with 1KHz audio tone for audio troubleshooting. User friendly interface for easy operation.
-
product
Multi-Tone Test Systems
AR RF/Microwave Instrumentation
AR’s state-of-the-art multi-tone systems are designed to test RF Radiated and Conducted Immunity faster than ever before. Both the MT2IEC10V3M and MT4IEC10V3M fully comply with IEC 61000-4-3:2020 Edition 4, allowing for multiple tone testing, reducing test time by up to 74%. Commercial, aviation, and automotive industries, will perform RF radiated and conducted immunity testing faster, more accurately, more efficiently, and more closely to a real-world environment.
-
product
NTSC PATTERN GENERATOR
PG-28
Model PG-28 NTSC Pattern Generator can be use to quickly and easily troubleshoot, test, and align NTSC television. Features a wide selection of popular video patterns including Color Bars, Crosshatch, Dot, Staircase, Circle, Center Cross, Window, and Raster for accurate and comprehensive TV troubleshooting and testing. Supports both progressive and interlace scanning system. Composite video and S-Video output. 1KHz audio tone for audio troubleshooting.
-
product
LanCaster
4402700
Indicates all common wiring faults including split pairs Shows which end the installed link contains the fault Cable Length Meter, Tone Generator & Service Indicator Instant digital display gives unambiguous fault indication Rugged Palm-Top design weighs less than 350g (12oz) Complete with 1 Active Remote unit and test leads Up to 16 unique Active Remote units / Office Identifiers
-
product
Tone Generator
140BMC/6P
The following tests can be performed using the 140BMC/6P Tone Generator:*1000 Hertz or 500/1000 hertz alternating tone for tracing pairs.*Locates broken pairs/cables in walls. *Tone generator emits R.F. signal detectable by Aines Model 250SSP STATIONMAN Probe or 350 Filter Probe.*Provides talk power on dead pair.*Checks for shorts or opens, using a long-life lite-emitting diode (LED).*Continuity test.*Tip & Ring identifications.*Line condition identification. a. Clear line. b. Busy line. c. Ringing line.*Positive line verification.*Long battery life.*Nylon braided tinsel test lead wire for greater wear and flexibility.*Heavy duty nickel silver Aines 6P type alligator clips with custom designed vinyl boots.*Rubber grommet to prevent chafing on the test leads.
-
product
Cable Tester/Tracer/Toner, 3-In-1 Professional, Pocket
TCT-700
A mult-function test set for RJ-45 LAN cable, BNC and "F" coaxial cable, tone generator, continuity and 6P2C/4P2C jacks. Ideal for electricians, service technicians. telecommunications, networking or general home use.
-
product
Linemen's Test Set
TeleTalker 330
Triplett Test Equipment & Tools
The Triplett TeleTalker™ 330 is a high performance lineman's test set with a weather resistant seal. This butt set offers many standard features not found on more expensive models like dedicated store / redial buttons, adjustable volume, Pulse and Tone dialing, and more. The high impact and weather resistant case allows for this product to be used in all demanding industry settings and features a full 3 year warranty. The user-friendly layout helps installers get the job done effectively with ease. The TeleTalker™ 330 requires no battery for main use and can store up to 10 frequently dialed numbers. Complete with angled bed of nails (JS Popper) test clips.
-
product
Mini Lan Cable Tester
MT-7058
Complies with CE safety standardAutomatically detect good connections, opens, crossed wires & split pairsTest RJ45 TIA568A/B (AT&T) 258A), 10 Base-T, Token ring, RJ-11/RJ-12 USOC and coaxial BNC cablePin to pin cable map indicatorNon-contact voltage detection for user safetyTraces wires with tone & remote lights allows one person operationCompact size and lightweight design for easy to carry aroundCircuit Protection for both units to ensure the testing qualityLow power consumption with auto power off function to preserve batteryLong cable test more than 300 meters
-
product
Telephone Wire Cable Tester For Testing Continuity With Sender And Receiver
PHCT55
The PHCT55 is a two-piece item that tests telephone wire continuity. Play a test tone on one end and listen on the other, judge continuity, and diagnose break points.
-
product
SNAPSHOT
PH-200
The Snapshot cable checker gives professionals and layman the ability to check cables instantly upon plug-in, with no buttons pressed or displays read. With its built-in memory, the Snapshot simply checks each cable plugged in against a correctly-configured cable pre-set by the user, and indicates the cable’s status with a sound. For pin-by-pin cable checking, the 〝standard check〞mode offers a plain LED-displayed check of the cable’s pins, checked automatically or manually. The Snapshot also generates a tone along the length of cables, making finding and following the cable with a tone probe a snap. A remote unit allows testing of already-installed cables, and a built-in line tester verifies phone line polarity and detects voltage before it threatens the safety of the test unit. A shield-test feature automatically tests cable shielding and a battery-low indicator prevents misreading results.
-
product
LAN Tester
RJ45
This easy to operate LAN tester enables you to test your wiring and connections at installation or after maintenance, making it one of the most convenient tools on the market. With the press of a single button you can automatically run a barrage of tests, including tests for Continuity, Opens, Shorts, Crosses and Splits. You can also identify which pairs require correction; The unit will scan all combinations without you having to do anything other than initiate the test. Even cable shield is tested for continuity! Building on the features provided by other testers such as the CZ20250, this LAN tester will also test coax networks and provide a tracing tone for cable identification. And it tests for all these at lightning speed, saving you as much time as possible.
-
product
Audio Test Tone Generator
ToneGenerator
Tone Generator is a sine wave generator, frequency generator and signal generator that lets you create audio test tones, sweeps or noise waveforms using your computer or a PDA handheld. Generate sine wave, square wave, triangular waveform, saw tooth waveform, impulse, white noise and pink noise.
-
product
Tone Generator
Control and test 2-way radio systems, repeaters, ANI, Paging and more. Activate 2-tone or 5/6-tone pagers. Operate or test EIA tone-remote systems. Record generated signals to a WAV file Accomplish MORE, by carrying LESS hardware in the field. Monitor inputs and outputs with our FREE built-in audio scope and spectrum analyzer. No external hardware required. Output may be fed directly into radio, twisted pair, or service monitor.*
-
product
LAN Cable Tester
PA-01D
The LAN cable tester is a versatile, full-featured tool for testing many kinds of network cable. Loopback and remote tests may be performed automatically or manually, and will test cable continuity as well as identifying opens, shorts, reversed wiring, and miswiring in cables up to 2,000 ft. long. Shielded connectors allow the tester to test shielded twisted pair (STP) cables. The built-in tone generator generates a low emission frequency tone which can be detected by any market tone probe, making it easier to trace and locate cables. Uses 1 9V alkaline battery. CE Approved.
-
product
6 Sided Bed of Nails Testers
BoxProber Family
6 sided Bed of Nails circuit board test fixture. Probes top bottom and all 4 sides. Central camming mechanism pull plates inward. Mechanically or electrically actuated options. Designed primarily for testing products in plastics. Side access electrically probes outside panel connectors. The unit will also optically read LEDs and key segments off LCD displays. Solenoids will press buttons and servos will turn selector switches. DC motors are used to adjust multiple turn potentiometers. Microphone will detect audio output tones. Top and bottom of circuit boards can also be probed if removable access panels are available. This unit will also probe all 6 sides of a circuit board. This is typically utilized in applications where connector testing is required.
-
product
Network, Port ID And Cable Tester
One for All PH-400
The One For All is an all-in-one network tester, tone generator, cable tester, and port ID finder. It comes with a remote unit, allowing pin-by-pin tests of installed cables in addition to patch cables. The office ID feature allows the user to check the ID number of up to 100 networks or patch panel outlets without labeling the cables manually, and the tone generator traces cable using a tone detectable by any market tone probe. The network tester blinks the network hub or NIC port light for the cable being tested, allowing easy cable and outlet identification; and it identifies network speed (10 Mbps vs. 10/100 Mbps vs. 10/100/1000 Mbps) and activity. Line tester included for detect live circuits and preventing damage to the tester.
-
product
Cable Fault Locator
TX4000
Auto Fault Location Rugged Palm-Top design Weighs less than 350g (12oz) 11 Measurement Ranges up to 4000m 25, 50, 75 & 100ohm Selectable Cable Impedance User Variable Gain Control Built in Tone Generator for Pair Tracing and Identification Suitable for testing all Communication and Power Cables Environmental Protection IP54 CE Approved Soft bag & Test Leads
-
product
Trailer Buddy 4/5 Pin One Man Trailer Wiring Tester
220
*Tests 4 & 5 Pin Flat connector wiring *Each signal from vehicle emits a unique tone *Loud beep can be heard over shop noise *One person makes complete test in 30 seconds! *Just apply brakes, turn signals, running lights& engage reverse *Tester also emits unique tone for any shorts in the wiring! *Greatly reduces time spent verifying vehicle trailer wiring *Very simple & easy to use - saves time!
-
product
LanSeeker Cable Tester
#TP500C
The LanSeeker is a fast, rugged cable tester and tone generator in one unit. It displays cable test results using LED indicators on the main and remote unit. An easy-to-use professional grade tool, the LanSeeker is a must have for residential and commercial cable installers. When the unit senses a connection between the main and […]
-
product
LANTRACKER
PH-100/120
The Lantracker is a network tester, pin-by-pin cable tester, and tone generator all in one. As a network tester, it detects whether a network is active or inactive and displays network speed (10/100/1000 Mbps) in either case. It also flashes the network hub or NIC’s port light corresponding to the cable it is connected to, to show the cable’s port number. As a cable tester, it performs loop-back or remote tests of network, data, voice, and coaxial cables, displaying the results on a pin-by-pin LED display which moves from pin to pin automatically or manually. The Lantracker can be used to test cable or shield integrity, testing network function and speed, and tracing cable using its tone generator function (tone probe not included). Includes an adaptor for testing coaxial-F cable. Uses 1 9V battery.
-
product
Test Cables
Test cables for tone generators, butt sets, oscilloscopes, digital multi-meters (DMM), and other test equipment that uses specialized connectors like Bed of Nails alligator clips, RJ11, sheathed banana plugs, etc. Our cables are similar and replaces genuine manufacturer cables from Fluke, Harris, Tektronix, HP, JDSU etc.
-
product
Mouth Simulator
BO1032
As consumers demand smaller devices that produce better sound and need better microphones, you need to test your microphones using more than a simple 1kHz tone. Sweep tests require a good mouth simulator that can produce a sweep with a known steady SPL.
-
product
Mobile sound Level Meter
SoundMeter
SoundMeter turns your iOS device into a handheld sound level meter (SLM) with support for exponential-time-weighted sound level (Lp) and equivalent sound level (Leq) measurements with various time and frequency weightings. The built-in signal generator tool can be used for generating calibration test tones, noise, chirps, or other periodic signals. SoundMeter also offers additional tools via in-app purchase, including a Noise Dosimeter and a whole or 1/3-octave real-time analyzer.
-
product
Test Set
TS® 25D
This feature-rich test set is a necessity for a variety of installs. The TS25D Test Set features data lockout and lockout override, making you completely safe in talk or monitor mode. The DSL/POTS filtering technology allows you to safely draw dial tone without downing DSL.
-
product
Test DVD For OmniMic Precision Measurement Systems
OMDVD Version 1
The Dayton Audio OMDVD Test DVD brings the ease of the OmniMic V2 system to measurements of 5.1-channel audio systems. It’s the essential tool for professional installers and home theater enthusiasts to ensure proper audio calibration and optimization of a home theater or multichannel music system for the highest possible performance. The full functionality of the OmniMic V2 measurement system is now available through every channel of a 5.1-channel audio system thanks to the OMDVD Test DVD’s suite of high-quality test tones, and an intuitive menu structure that has been optimized for ease of use.
