Battery String
-
Product
Battery Monitoring System
S5
-
BTECH's benchmark product designed for a wide variety of applications (UPS/Telco/Switchgear), the S5 can collect data from any battery type including cells with the highest amp hour rating (4000+), and the S5 systems will record all battery parameters.
-
Product
Battery Testers & Analyzers
-
Wuhan Fanke Transformer Manufacture Co., LTD
Battery testers & analyzers
-
Product
Battery Backup IC
-
Analog Devices offers a range of supervisory circuits that offer a complete single chip solution for power supply monitoring and battery control functions in microprocessor systems. Functions include microprocessor reset, backup battery switchover, watchdog timers, CMOS RAM write protection, and power failure warning.
-
Product
Digital Battery Load Tester
DBT125
-
Battery load test. Depending on the size of the battery, this product adds a very high load to the battery (125 A). It enables the reading of battery condition by voltages and by its ability to maintain the load, thus determining levels of sulphation.
-
Product
Continuity Tester Supplied without Battery
22700
-
Use to test for continuity with power disconnected. Excellent for use on marine, recreational and general automotive vehicles. Test appliances and other electrical circuits with power off. 48" lead wire. Uses AA 1.5 volt battery (not supplied).
-
Product
Battery Monitoring System
-
JUNXY Battery Monitoring Systems are designed in accordance with IEEE Battery Maintenance recommendations. This allows you to maintain a safe and secure system with Real-time monitoring, which will minimize the probability of a failure and optimize the service life of the battery. JUNXY Battery Monitoring Systems not only monitor the batteries, but also the external parameters which could affect the performance of the system, providing added security. It is a powerful tool for mitigating and preventing costly downtime due to unexpected system failure.
-
Product
Battery Test Equipment
-
The multi-current range battery test systems M340A and G340A are designed for precision battery charge/discharge test, coulombic efficiency (current efficiency) test and supercapacitor test. Voltage and current test accuracy go down to 0.01% of the selected range.
-
-
Product
4U Rackmount Chassis With Battery Backup Unit
IPC-610LMB-40BEA1
-
Built in 36,000mAh Ni-MH battery to prevent blackout and AC power instabilityBattery supports 6-minute backup time (at 200W)Supports an ATX motherboard up to 7 slotsShock-resistant disk drive bay design holds up to three 5.25" and one 3.5" disk drivesSpecial hold-down clamp design with rubber cushions protects the cards from shocks and vibrationsPower and HDD activity notification improves system availabilityFront-accessible air filter for easy system maintenanceLockable front door prevents unauthorized access
-
Product
Self-Rectified Generator Power Supply Crawler Battery 50 to 180 kV
SITEX C1802
-
Self-Rectified Generator Power Supply Crawler Battery
-
Product
Battery Remote Maintenance System
-
Fuzhou Fuguang Electronics Co., Ltd.
Battery Remote Maintenance System
-
Product
Low Voltage DC / Battery Powered HV Amplifiers
WMA-02 And WMA-02LF
-
The Falco Systems WMA-02 is a high voltage amplifier that runs from an 24 - 30V DC power supply and can be battery powered if required, e.g. for use in a Faraday cage. Its internal high voltage generator is inductor-free and hence does not spread magnetic interference in sensitive experimental setups. The output noise is impressively low at 4mVrms. For extremely low noise applications where bandwidth is not an issue, a dedicated WMA-02LF version is available that contains an output low pass filter capacitor which reduces the bandwidth to 50Hz, but makes the noise drop to below 0.2mVrms. This bandwidth-limited amplifier is ideal for MEMS or piezo positioning with manual voltage adjustment.
-
Product
Handheld Digital Multimeter, 4.5 digit, up to 800 hours battery life
U1282A
-
60,000 counts resolution on dual display0.025% basic DC voltage accuracy Longer battery life up to 800 hours Certified to IP 67 for dust and water protection Tested to withstand a 3-meter (10-ft) drop Programmable via USB (Download Programming Guide here)CAT III 1000 V/ CAT IV 600 V overvoltage protection Vsense for non-contact voltage detection Square wave output for generating pulse width modulation (PWM) signal Frequency counter Low pass filter
-
Product
Battery Test System
WBCS3000Ls32
-
Low current model32 channel battery cycler (expandable up to 128 channels)No. of minimum channel : 16 channelsmax. voltage range : ±5Vmax. current range : ±10mA
-
Product
Battery Analyzer
SI-9300R
-
Conventional cycler systems use PCs to transfer data from cycler channels to disk. SI-9300R instead uses advanced technology to write data direct to disk without PC intervention. For high channel count systems this dramatically reduces PC workload, increases system reliability and allows the PCs to concentrate on test control, channel monitoring and data analysis.
-
Product
High Voltage Benchtop Battery Tester 1000V Max input
BT3564
-
Hioki benchtop battery testers support simultaneous high-speed measurement of the internal resistance and battery voltage of EV and PHEV battery packs. The BT3564 Battery HiTester can measure pack voltage and total resistance, as well as bus bar resistance up to 1000V.
-
Product
Scienlab Battery Test System – Module Level
SL1001A Series
-
The SL1001A and SL1006A Battery Test Systems – Module Level Series help you emulate sink and source for battery modules for automotive and industrial applications.
-
Product
Motorcycle Battery Testers
-
ELAK Motor-Cycle Battery Testers are designed for testing batteries used in motor-cycles, scooters, ATV''s, etc. These testers check the voltage drop of the battery under a fixed load and confirm the status of the battery full, weak or dead. The new generation motor-cycle and scooters are fitted with an electrical start. It is therefore very essential to test these batteries under load, to ensure that the batteries are capable of starting the vehicle.
-
Product
CYCLOPS Battery Powered Headlamps
CY3-LED
-
*LED light mounts on hard hat and allows quick and efficient hands-free movement*Allows for even distribution of weight across the forehead*Water-resistant*Field replaceable batteries
-
Product
Battery Module Test Chambers
-
Guangdong Bell Experiment Equipment Co.,Ltd
This test chamber series mainly for testing the battery module of Electric-bike, Electric Motorcycles, etc. These series meet the standard compliance of IEC62619, UL2580 and GB31485-2015. Including short circuit, thermal test, drop test and crush test, etc.
-
Product
Battery Tester
BAT-250
-
The Amprobe BAT-250 Battery Tester is designed for one-handed, comfortable and reliable battery measurements. The uniquely designed tester offers an ergonomic slider and a v-shaped side cradle to better hold batteries in place during testing and a contoured case shape that fits neatly in your hand. Testing your batteries has never been easier.
-
Product
Intelligent Battery Tester
CHROME
-
Simulating a 20 hour discharge test in seconds, the ACT CHROME displays the DC Voltage and available Ampere hour (Ah) capacity of standby lead acid batteries between 1.2Ah and 200Ah.
-
Product
Lead-acid Storage Battery Analyzer
-
From the beginning of 2006 the verification of measurements of the analyzer of lead-acid chemical sources developed by Company "Megaron" is spent in Test laboratory "Neva-Reglament". The analyzer is intended for the express-estimation of a condition of lead-acid batteries: before the first use of new battery (an estimation of the electric characteristics declared by the manufacturer); during the battery operation (an estimation of a condition and working capacity at real application).
-
Product
Low Voltage DC / Battery Powered HV Amplifiers
WMA-01 And WMA-01LF
-
The Falco Systems WMA-01 is a high voltage amplifier that runs from an 24 - 30V DC power supply and can be battery powered if required, e.g. for use in a Faraday cage. Its internal high voltage generator is inductor-free and hence does not spread magnetic interference in sensitive experimental setups. The output noise is impressively low at 3mVrms. For extremely low noise applications where bandwidth is not an issue, a dedicated WMA-01LF version is available that contains an output low pass filter capacitor which reduces the bandwidth to 50Hz, but makes the noise drop to below 0.1mVrms. This bandwidth-limited amplifier is ideal for MEMS or piezo positioning with manual voltage adjustment.
-
Product
Scienlab Battery Test System – Pack Level, 110 KW Extendable Version
SL1720A
-
Keysight’s SL1700A Scienlab Battery Test System – Pack Level Series allows to realistically emulate the environment of the future battery pack application in order to test the high-power battery pack comprehensively and improve its functions and safety. The growing demand of e-mobility increases the need of vast battery test labs for EV battery development.
-
Product
Battery Testers
-
Shanghai Beha Electronics Co., Ltd.
*can measure the resistance of rechargeable batteries and DC voltage.*can also test Ni-cd, Ni-MH, Li-ion batteries.*DC Voltage measurement.*4-wire resistance measurement.
-
Product
Battery Test Chambers
-
At Weiss Technik we supply battery test chambers specific to testing batteries in a variety of conditions including low or high temperatures, humidity changes, vibration changes, and altitude changes. Our battery test chambers are designed to test Lithium Ion batteries, lead acid, Battery Managements Systems (BMS), battery packs, modules, battery cells, and more.
-
Product
Battery Portable Passive Intermodulation Analyzer
iPA Series
-
The iPA Series Passive Intermodulation (PIM) analyzer is the first battery powered PIM Test Analyzer versatile enough to support multiple test scenarios such as testing at the top of the tower, base of tower, roof top and in-building for DAS systems. This IEC compliant 20W, rugged, battery operated design includes a tablet computer in a ruggedized case for remote control. This allows hands-free dynamic testing that is safe and convenient. Add the optional Range to Fault (RTF) module to quickly identify the location of PIM and Return Loss sources.
-
Product
Precision Integrated Analog Front End, Controller, & PWM for Battery Test & Formation Systems
-
The AD8452 combines a precision analog front-end controller and switch mode power supply (SMPS), pulse-width modulator (PWM) driver into a single silicon platform for high volume battery testing and formation manufacturing. A precision instrumentation amplifier (in-amp) measures the battery charge/discharge current to better than ±0.1% accuracy, while an equally accurate difference amplifier measures the battery voltage. Internal laser trimmed resistor networks establish the in-amp and difference amplifier gains (66 V/V and 0.4 V/V, respectively), and stabilize the AD8452 performance across the rated operating temperature range.
-
Product
Desktop Cell And Battery Testers
-
Maximize your testing capabilities with Maccor's hardware and software, conveniently packed into a compact desktop unit. Our comprehensive turn-key systems come bundled with all the essentials to jumpstart your testing process. Select from multiple options and configurations to match your requirements.Desktop testers can be configured with multi-current range channels that have an accuracy of ±30 ηA on the bottom range or single range channels configured to meet your needs. Contact Maccor for pricing and availability.
