Utility Locaters
-
Product
Utility Detection Radar
DS2000
-
There’s a lot going on underground that you need to know about before you ever start to dig. The Leica DS2000 Utility Detection Radar finds all potential threats, including non-conductive pipes and fibre optics, increasing safety by lowering the risk of accidently hitting underground assets. Increase safety, speed up work and lower asset management costs with the ability to prevent hazardous outages and collect more information. The DS2000 betters your business by making it safer, faster and more efficient.
-
Product
High Power Fiber Optic Visual Fault Locator
VFL-700
-
Shanghai Fibretool Technology Co.,Ltd.
The VFL-700 is specially designed for field personnel who need an efficient and economical tool for fiber tracing, fiber routing and continuity checking in an optical network during and after installation.
-
Product
Handheld Cable Fault Locator
TM800H
-
TM800H Handheld Cable Fault Locator adopts TDR (Time Domain Reflection), new signal process and data collection technology. It can locate the distance of cable break and mix faults accurately. TM800H can be widely used in the communication installation, maintenance and general wiring. It can troubleshoot not only the local Telco-cable, but also Network cable. Its high sampling rate makes the measurement dead zone as narrow as 1 meter. This makes it a straightforward, user-friendly test solution.
-
Product
Visual Fault Locators
-
Shanghai Joinwit Optoelectronic Tech,co.,Ltd
Joinwit Visual Fault Locators
-
Product
Platinum Tools Fiber Optic Visual Fault Locator
#TVFL100
-
Fiber optic visual fault locator works with virtually all 1.25mm and 25mm fiber optic sizes and connector types.
-
Product
Visible Fault Locator
FiberLink 6656
-
Fiberlink 6656 Visible Fault Locator is a light-weight, hand-held tool used to quickly troubleshoot faults in the continuity of both single-mode and multimode fibers, especially at fiber launch points or in OTDR dead zones.
-
Product
Pre- Locator
CFL PL3+
-
The new generation CFL PL3+ Cable Fault Pre-locator from SCOPE is the ultimate solution for locating underground cable faults in minimum time. It uses advanced technology for fault distance measurement which helps even an unskilled operator to locate the fault accurately up to 128 km.
-
Product
Blockage Locators
-
Shenzhen Noyafa Electronic CO.,LTD
Noyafa Blockage Locator can be used in both household and engineering. The sensing range is enhanced, and it is free from external interference. It can pass through the 60cm-thick cement wall and the pipe blockage under the floor to reduce the removal area. Accurate detection and adjustable sensitivity.
-
Product
Visual Fault Locator
HW-205
-
Shanghai Fibretool Technology Co.,Ltd.
The HW-205 is specially designed for field personnel who need an efficient and economical tool for fiber tracing, fiber routing and continuity checking in an optical network during and after installation.- 2.5mm universal connector- Operates either in CW or Pulsed- Constant output power- Long battery life (up to 60 hours)- Laser case ground design prevents ESD damage- Portable and rugged, easy to use- Burning testing to ensure the reliability.- Optional 1.25mm connector adapter
-
Product
Utilities
-
Audio signal generator that include sine waves, square waves, white noise, and pink noise. The noise signals may be octave-band limited. In landscape mode, you can set sweep start and stop frequencies, and a time in seconds.
-
Product
Tool, Crimp, QuadraPaddle And TriPaddle, Receiver And ITA, Locator Required
910101103
Crimp Tool
Tool, Crimp, QuadraPaddle and TriPaddle, Receiver and ITA, Locator Required
-
Product
Underground Cable Fault Locator
KM-CFPL-620 /620B
-
Kusam Electrical Industries Limited
“KUSAM-MECO” underground Cable Fault Pre-locator is an automatic Cable Fault Locator which adopts ARM, FPGA & Dot Matrix Color LCD display Technology. This tester combines both pulse reflecting technology (TDR) & (intelligent Bridge testing (Bridge) (Model-KM-CFPL-620B) for measuring the exact fault location such as broken line, cross faults, earthing, (poor insulation & poor contact of the lead covered cables as well as plastic cables. (Model-KM-CFPL-620B)).It is a microprocessor based fault locator with a user friendly menu. It is easy to operate. It tests almost all telecom & signal cables. It has an English menu which is easy to understand & use. With Megameter & Ohmmeter it enables to test insulation resistance & loop resistance. It has USB Port for uploading test data to computer
-
Product
VALVE & BOX LOCATOR
7-T
-
Rugged "Cycolac" instrument housing and detection headTelescoping HandleVisual Meter & Battery TesterBuilt-in speaker, signal and battery test meterOne sensitivity control knobBalanced and lightweight Adjustable extensionSet of stereo headphones3 Replaceable "AA" Alkaline batteriesDependable
-
Product
15" XGA Industrial Monitor For Hazardous Location, With "316L Stainless Steel Front Panel"
FPM-8151H
-
15" XGA TFT LCD with "LED backlight"Stainless steel 316L front panelIP65 compliant front panel-20 ~ 60°C (-4 ~ 140°F) wide operating temperature rangeEnhanced 5-wire resistive touch panelDirect VGA & DVI-D video input interfaceCombo RS-232 & USB interface for touchscreen functionSupports 24 VDC input and 100~240 VAC input (optional AC adapter)OSD control pad with lockable function on front panelCertified with UL CID2 for hazardous environment
-
-
Product
End-to-End Testing of Location Based Services Software
-
LBS Tester provides an end-to-end test bed for Mobile Network Operators and Network Equipment Manufacturers, to verify the accurate implementation of the location services network. The LBS Tester tests that the Location Server (System Under Test) is correctly executing the positioning procedures over the control plane and/or user plane of that network. To test normal signaling, or failure scenarios, over the LTE User Plane as the number of SETs (SUPL Enabled Terminals) simulated by the LBS Tester increases, the Location Server must execute LPP (Location Positioning Protocol) procedures over SUPL (Secure User Plane Protocol) with success, or without, respectively.
-
Product
Mobile Problem Locator
MPL
-
The ComSonics Mobile Problem Locator (MPL) application is a smart phone application designed to provide cable technicians with a simple tool to help maintain their network. Targeted for use with ComSonics' QAM Compass via Bluetooth connection to provide contractor work verification.
-
Product
650nm Visual Fault Locator
-
Shanghai Baudcom Communication Device Co.,Ltd.
Visual Fault Locator series Visual Fault Locator uses the DFB-LD as the emitting component. Driven by constant current source, the indicator can emit stable red laser.The product can be used to inspect fiber failure when they connect with optical interface and be inserted into single mode or multi mode optical fiber.It is indispensable tool in fiber project constructing, fiber net-work maintaining, optical component manufacture and research.
-
Product
Ground Fault Locator
K-800
-
Kongter Test & Measurement Co., Limited
Kongter’s K-800 Ground Fault Locator is the new model which is developed to fast detect, trace and pinpoint virtual ground faults in LIVE DC systems where electrical cables have breakage with current lost to ground.
-
Product
Time Domain/Fault Location Analysis For E5061B
E5006A
-
The E5006A Time Domain/ Fault Location Analysis option allows you to locate the discontinuities and mismatches of devices such as cables. By employing the gating function in the time domain and transforming the data back to the frequency domain, you can remove unwanted responses of connector mismatch in your fixture. In addition, the cable SRL (Structural Return Loss) analysis capability is provided with the E5006A.
-
Product
Pipe & Cable Locator
505
-
Split box locator, Inductive Operation, Conductive Operation, Locate Unknown Pipes, Peak Method, Null Method, Very Accurate Depth Location.
-
Product
Cable Fault Locators
-
Every day, GAOTek cable fault locators are used by electricians and technicians to find faults and breaks in underground electrical and communications cables.
-
Product
Rebar Locator
Profometer PM-630 AI
-
The Profometer PM-630 AI advanced cover meter is a sophisticated instrument extending the application range of the Profometer PM-600 with the Line and Area Scan Modes and an extensive choice of statistical views.
-
Product
Visual Fault Locators
MVFL Series
-
Shanghai Tarluz Telecom Tech Co., LTD
MVFL series Visual Fault Locators is meet the Class IIIA product, which is the easiest way to identify fibers from end to end and locate polished connector endfaces. Its red laser shines through most yellow-jacketed fibers to help you pinpoint breaks, bends, faulty connectors, splices and other causes of signal loss. The 1mW output power enable the MVFL has a reach of up to 5 km. MVFL seires VFL locates faults visually by creating a bright red glow at the exact location of the fault on single mode (SM) or multimode (MM) fibers. Due to its small size, lightweight and simple but proven design, the MVFL can accompany you anywhere In your pocket or belt pouch in harsh environment
-
Product
Fault Locator
REZAP FAULTMASTER
-
REZAP FAULTMASTER is an auto-recloser that keeps customers on supply during intermittent faults.
-
Product
Pre- Locator
CFL PL3
-
CFL PL3, new generation Cable Fault Pre-Locator from SCOPE is the ultimate solution for locating underground cable faults in minimum time. It uses advanced technology for fault distance measurement which helps even an unskilled operator to locate the fault with accuracy.
-
Product
Utilization Planning, Radio Network Configuration, Data Distribution
SOVERON
-
R&S®SOVERON® management software supports centralized network management, where a central organizational unit performs complete mission planning as well as decentralized management, where the various configuration steps are made at different military hierarchy levels.
-
Product
VHF/UHF Handheld Signal Location Antennas
Type NVF-2
-
The Type NVF-2 series of handheld directional antennas are used to locate interfering signals or noise in either the 420 – 470 MHz (Type NVF-2A) or the 900 MHz ISM band or cellular telephone bands (Type NVF-2B). Both models incorporate a solid reflector positioned behind a resonated half wave driven element, both elements being mounted on a fiberglass rod with an integral pistol grip. The configuration of the reflector and driven element are such that a deep null in the signal being received will occur when the antenna is pointed in the direction of the signal being radiated. A T-pad resistive attenuator is also incorporated in the antenna mounting enclosure to aid in the direction finding process on very strong signals or when excessive reflections present multiple returns.
-
Product
Power Utility Industry
-
Major product types include:*Auxiliary and Tripping Relays*Test Blocks*Arc Flash Protection*Utility Grade Protection and Control Relays*Industrial Controls and Pilot Lamps*On Board Railway Relays, CB’s and Panel Meters
-
