-
Product
Mixed Signal Oscilloscope 1 GHz, 4 Analog Plus 16 Digital Channels
MSOX3104G
-
The MSOX3104G 1 GHz oscilloscope provides 4 analog plus 16 digital channels, 4 Mpts memory, 1,000,000 waveforms/sec update rate, zone touch trigger with an 8.5-in capacitive touch screen, and standard embedded software with waveform and measurement histograms.
-
Product
LXI Reed Relay Matrix - Dual 32x16 Plugin, Direct Y Access, 3 Analog Buses
65-225-001
-
The range includes four plug-in models covering matrices of up to 1,536x4 in increments of 128 (model 65-221), 768x8 in increments of 64 (model 65-223), 384x16 in increments of 32 (model 65-225), and 192x32 in increments of 32 (model 65-227). Users can specify as many or as few plug-in modules (up to six) required and can field upgrade the chassis to extend the matrix when necessary. Another important feature is that over 1,500 relays can be closed simultaneously for specific conditions for parametric testing.
-
Product
Infiniium V-Series Oscilloscope: 20 GHz, 4 Analog Channels
DSAV204A
-
20 GHz analog bandwidth (upgradable)4 analog channels Capture a longer signal trace with up to 80 GSa/s sample rate and 2 Gpts of acquisition memory Get the best signal integrity with the low noise floor (1.54 mVrms at 50 mV/div) and lowest jitter measurement floor (100 fs)See better measurement accuracy with ENOB values in excess of 5.5 and a SFDR exceeding 50 dBC Improve your testing with the broadest range of jitter, trigger, analysis and protocol tools (featuring Precision Probe)
-
Product
PXI 8 Slot BRIC 138x8 1-Pole Dual Analog Bus (3 sub-cards)
40-560A-121-138X8-M
-
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high-performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
cDAQ-9178, 8‑Slot, USB CompactDAQ Chassis
781156-01
-
8‑Slot, USB CompactDAQ Chassis - The cDAQ‑9178 is a CompactDAQ USB chassis designed for small, portable sensor measurement systems. The chassis provides the plug‑and‑play simplicity of USB to sensor and electrical measurements. It also controls the timing, synchronization, and data … transfer between C Series I/O modules and an external host. You can use this chassis with a combination of C Series I/O modules to create a mix of analog I/O, digital I/O, and counter/timer measurements. The cDAQ‑9178 also has four 32‑bit general-purpose counters/timers. You can access these counters, as well as share clocks and triggers, through two built-in BNC connectors.
-
-
Product
SH68M-68M-EPM, Male 68 pin SCSI to 68 pin VHDCI, 0.3m
192288-0R3
-
68-Pin Male VHDCI to 68-Pin Male VHDCI, Twisted Pair, Shielded Multifunction Cable - The SH68M-68M-EPM Cable, sometimes referred to as SHC68-C68-EPM, connects DAQ devices. The cable includes separate digital and analog sections, individually shielded twisted pairs for analog inputs, individually shielded analog outputs, and twisted pairs for critical digital I/O. The SH68M-68M-EPM Cable is offered in different lengths.
-
Product
PXIe 500 MHz Oscilloscope
M9242A
-
500 MHz bandwidth oscilloscope2 analog channels5 GSa/s sample rate1,000,000 wfms/s update rate Isolate signals in seconds with exclusive zone triggering Additional options: 20 MHz arbitrary waveform generator, 3-digit voltmeter, serial trigger and analysis and mask testing
-
Product
PXIe-5111, 350 MHz, 3 GS/s, 8-Bit PXI Oscilloscope
785769-11
-
PXIe, 350 MHz, 3 GS/s, 8-Bit PXI Oscilloscope—The PXIe-5111 oscilloscope has two channels that sample up to 3 GS/s with flexible and programmable settings for coupling, input impedance, voltage range, and filtering. PXI Oscilloscopes also feature a number of triggering modes, deep onboard memory, and an instrument driver that facilitates high-speed data throughput and includes analysis functions. This device is ideal for automated and partially automated applications that require flexible measurement configurations and up to 350 MHz of analog bandwidth.
-
Product
Mixed Signal Oscilloscope, 500 MHz, 4 Analog Plus 16 Digital Channels
MSOX3054A
-
500 MHz4 analog plus 16 digital channels Easily view your signals on the 8.5-inch WVGA display Capture more data with up to 4 Mpts memory See more signal detail with 1,000,000 wfms/s update rate Expand your measurement capabilities with full upgradability: Add bandwidth, memory, 20 MHz arbitrary waveform generator, 3-digit voltmeter, serial trigger and analysis, segmented memory & mask testing at any time
-
Product
USB-6343, 32 AI (16-Bit, 500 kS/s), 4 AO (900 kS/s), 48 DIO USB Multifunction I/O Device
782253-01
-
32 AI (16-Bit, 500 kS/s), 4 AO (900 kS/s), 48 DIO USB Multifunction I/O Device - The USB‑6343 offers analog I/O, digital I/O, and four 32‑bit counters/timers for PWM, encoder, frequency, event counting, and more. Onboard NI‑STC3 timing and synchronization technology delivers advanced timing functionality, including independent analog and digital timing engines and retriggerable measurement tasks. The USB‑6343 is well suited for a broad range of applications, from basic data logging to control and test automation. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
-
-
Product
Field Strength Meter
FIM-71 VHF
-
The Model FIM-71 is a portable, laboratory quality Field Strength Meter designed for rigorous field applications. Combining a calibrated half-wave dipole antenna and a highly accurate tuned voltmeter with a range of 140 dB, the FIM-71 is suitable for practically all types of RF emission measurements in the 45 MHz to 225 MHz spectrum. The operator can switch select wide or narrow bandwidth, peak or average value of TV or pulse modulated signals, AM or FM demodulation, and a meter dynamic range of either 20 dB or 60 dB. A dc analog output voltage, proportional to the meter indication, is provided for driving a chart recorder. A leveled output from the calibrating oscillator is available for measuring cable insertion loss, filter response, amplifier gain, and other signal ratio measurements. The 4-1/2 inch, taut band, mirrored scale meter is calibrated in volts and dB for precise measurements in field or laboratory environments.
-
Product
LXI Reed Relay Matrix - Dual 64x8 Plugin, No Direct Y Access, 6 Analog Buses
65-223-101
-
These Modular LXI Matrix Reed Relay Matrix Modules plug into our LXI Modular Chassis (model 65-200-002)—providing access to all signal connection on 200 pin connectors. They are constructed using Pickering Electronics' Reed Relays offering maximum performance and reliability as well as very fast operate times.
-
Product
PCI Multi-Functions Board
PCI-DSP-6713-MFIO
-
The board consists of private SDRAM and dual-ported SRAM attached to the DSP. An FPGA provides the timing and control as well as I/O drive for the 48 programmable I/O pins. Peripherals include a serial port and an USB port. Flash memory is available for downloading programs into a non-volatile memory. 16 channels of A/D and 16 channels of D/A provide analog interfaces to real-world signals
-
Product
Power Amplifiers for Radio Amateurs
-
From classic equipment for simple QSOs to high performance modules for contests, EME-operations and satellite radio: Our products provide absolute top performance. When choosing their equipment many radio amateurs and club-stations don't compromise and trust in the proven quality of Kuhne electronic amplifiers. Numerous contest victories, records and first contacts with a country were and are achieved with Kuhne products. Our amplifiers are remarkable for high gain and high linearity. LD-MOSFET and GaAs-FET-systems are the state-of-the-art technology in the amateur sector and enable the perfect use for all analog and digital modes (e.g. SSB, CW, WSJT, ATV, DATV). Small mechanical measurements and milled aluminum cases enable high temperature stability and tower mounting. Don't compromise and get technology from Kuhne electronic!
-
Product
CAT-5 Video Drivers
-
Analog Devices provides designers with a robust portfolio of high speed triple, differential, and single-ended input to differential output CAT-5 video drivers. We designed the technology for the highest resolution component video signals, but it can be used for any type of analog signals or high speed data transmission over either Category 5 UTP cable or differential printed circuit board (PCB) transmission lines. Manufactured with our second generation XFCB bipolar process, the drivers have large signal bandwidths of 700 MHz, fast slew rate, and output amplitude and phase matching balanced to –60 dB at 50 MHz.
-
Product
Insulation Tester, Analogue / Digital Megohmmeter, 50V, 100V, 250V, 500V, 1kV, 0.01ohm to 20Gohm
72-3105
-
Insulation Resistance Tester Full function DMM includes AC and DC voltage measurement, plus a wide range of resistance scales designed specifically for insulation resistance measurement. It is ideal for safety and preventative maintenance work on powered tools, motors, transformers and similar devices. Large backlit 6000 count display provides at-a-glance readings via both 3-3/4 digit readout and 45 segment analog bargraph.
-
Product
Portable Video Signal Generator
VG-882-A
-
Multi-interface signal generator for TV production line. Best cost performance. HDMI x 4 ports, PC analog and TV interfaces.HDMI ARC (Audio Return Channel) and 3D functions are supported as an option. HDCP / EDID / CEC testing of individual HDMI ports (Option) Remote box operation (RB-1870 or RB-1871) Program edit by software SP-8870 (USB communication)
-
Product
Silicon Steel Sheet Iron Loss Tester
DX-30SST
-
DX-30SST Silicon Steel Sheet Iron Loss Meter adopts SCM technique and analog electronics technique, the magnetic circuit of permeameter adopts low loss silicon steel iron core, it is a small tester for measuring the characteristics of silicon steel sheet, met the requirements of tracing the brand of silicon steel sheet.
-
Product
4AI/4DI I/O Module
WISE-S214-A
-
4 analog input and 4 digital inputModular IoT I/O module to pair with WISE-4200 series
-
Product
PCIe Direct Digital Synthesizer
-
These devices provide two synchronized DDS-based RF channels on a single PCI card. With fine frequency, amplitude and phase control the Synth1000 products enable a number of advanced applications at a fraction of the cost of conventional equipment. In addition to two analog outputs the Synth1000, up to 4 separate profiles may be dynamically selected using externally supplied TTL signals for low-latency triggered operation such as PSK, FSK, and triggered sweep operation. Software support for Windows 8, 7, Vista, Windows XP and Linux is included. LabVIEW Labview source code available. For detailed specifications, please refer to the Synth1000 Manual.
-
Product
16 Bit PXI I/O Board With 32 Or 64 Analog Outputs
CP266
-
The CP266 is a single-width, 6U, CompactPCI module with 32 or 64, 16-bit analog output channels. These independent analog channels provide ±10 V full-scale outputs. The channel update rate is 2ms, and each output is accurate to ±1mV. The power-up state of the analog outputs can be set to independent user-defined values. Paired output signals are provided to eliminate ground offset effects. The analog outputs are available at a single 68-pin SCSI II shielded connector (32-channel option) or a pair of 68-pin SCSI II shielded connectors (64-channel option).
-
Product
Analysis Tool for ECU Networks and Distributed Systems
CANape
-
The primary application area of CANape is in optimizing parameterization (calibration) of electronic control units. During a measurement process, you can simultaneously calibrate parameters and record signals. The communication between CANape and the ECUs takes place via protocols such as XCP or via microcontroller-specific interfaces with the VX1000 measurement and calibration hardware. CANape supports various ADAS sensors such as radar, LIDAR and video. Combined with high-performance hardware, CANape can store multiple gigabytes of data per second. Calibration data management and convenient measurement data evaluation including data management as well as reporting make CANape a complete tool for ECU calibration. Of course, CANape also provides access to bus data, diagnostic data and analog measurement data.
-
Product
High Speed ADC > 10MSPS
-
Analog Devices high speed A/D converters (ADCs) offer the best performance and highest sampling speed in the market. The product offerings include high IF ADCs (10 MSPS to 125 MSPS), low IF ADCs (125 MSPS to 1 GSPS), integrated receivers, and wideband ADCs (>1 GSPS). The High speed ADC portfolio offers solutions for all high speed conversion applications.
-
Product
Waveform Generators
-
Specialized tools designed for creating and controlling analog signals.
-
Product
Gasoline Engine Tachometer
SE-1620
-
The SE-1620 is an engine tachometer that performs measurement of the number of revolutions of a gasoline engine by connecting an engine revolution sensor such as an ignition pulse detector. A 100-mm wide-angle meter is used for the display, and both analog output and pulse output functions are provided as standard.Simply attach an ignition pulse detector or one of our other compatible detectors to the engine to enable measurement of the number of revolutions of a gasoline engine. The inputs, outputs and input power supply are all isolated to ensure the output of analog and pulse signals with superior noise resistance and stability characteristics.
-
Product
Temperature and Process Controllers
-
Watlow Electric Manufacturing Company
Temperature and process controllers include one or more sensor inputs with open-loop break detection and multiple outputs for control and alarms. Various configurations offer auxiliary analog inputs, automatic tuning, TRU-TUNE®+ adaptive control, and ramp and soak profiling. Output options include analog process, switched DC and mechanical, solid state and no-arc hybrid relays. Other features include countdown timer, user-customizable menu, burst fire output control, failed heater/load detection and NEMA 4X (IP65, IP66).
-
Product
5 Channel DAC FMC Module
DACNF05 – HPC
-
Sundance Multiprocessor Technology Ltd.
The RFM-DACNF05 is a five channel Digital to Analog converter FMC which complies with VITA 57.1-2010. Each channel provides 16-bit single-ended input and one DC coupled differential analog output with 1 – 500MHz sampling speed based on Maxim MAX5888A. A single-ended external input or output clock is provided. The direction of the clock is programmable from the FPGA of the FMC carrier board.
-
Product
Smart Analog
-
Sensing devices play an increasingly important role in many areas of modern life — at our workplace, in industry, at home, as well as our personal mobile devices. In consumer applications, sensor-based electronic control provides us with additional safety, health information, power savings, and overall convenience. And for more complex systems in industry and commercial applications, the trend is toward more intelligent sensors that deliver more precise and "intelligent" data to improve product quality, increase operational savings, and reduce energy consumption.
