DC Load Banks
See Also: Load Banks, AC Load Banks, Inductive Load Banks, Reactive Load Banks, Resistive Load Banks
-
Product
Partial Load Failure
PLF Device
-
The control device series “PLF” has been designed to monitor the partial and/ or total failure of the alternating current absorbed by loads driven by static switches and / or electromechanical relays.
-
Product
S-Type Load Cells
-
S-Type load cells are low-cost and high performance side mounted load cells suitable for a number of weighing and general force measurement applications. They come with a 6-foot strain relieved integral cable with pigtail leads that are stripped and tinned for electrical interface.
-
Product
Dummy Load
-
Dummy load is capable of dissipating four times the legal limit 6 kW for 2 minutes and legal limit 1500 watts key down, forever. It covers the 160 meter to 6 meter bands (actually 1 Mhz-60 MHz continuously). It is a dry dummy load intended for testing amplifiers and station conditions. Two fans on the rear of the unit are automatically turned on when the internal temperature reaches 120°F/49°C . The unit runs off a universal AC supply. Simple to operate and use, the dummy load includes an RF sample output of -60 dBc.
-
Product
Power Bank Capacity Tester
TOB-BTS-6V4A
-
Xiamen Tob New Energy Technology Co., Ltd
Power Bank Tester Used For Power Bank Capacity,Voltage And Cycle Testing. The TOB-BTS-6V4A Power bank tester is used for power bank quality detection, it can test the power bank capacity, voltage and life cycle performance with connecting computer.
-
Product
Resolver to DC Sine / Cosine or Synchro to DC
ST-RD & ST-SD
-
Computer Conversions Corporation
ST-RD and ST-SD Series - Resolver to DC Sine / Cosine or Synchro to DC Sine Cosine Packaged on PCB with Track and Terminal Block and On-Board AC Reference Supply may be used driving DC Servo amp in active position synchronizing applications
-
Product
High Slew-Rate High Power DC Electronic Load （100A/μS）
34110A-11（10KW）
-
34000A Series has its own control and display panel, CC / CR / CV / CP / Dynamic modes, 150 sets Store / Recall memory which provides load set-up more efficiently, also can be remote controlled via GPIB、RS232、USB and LAN interface.
-
-
Product
Autoranging System DC Power Supply, 750 V, 20 A, 5000 W, 400 VAC
N8944A
DC Power Supply
The Keysight N8900 Series is a family of 5 kW, 10 kW, and 15 kW autoranging, single-output power supplies available in 14 different voltage, current, and power combinations and either 208 VAC or 400 VAC (28 total models).
-
Product
Programmable DC Electronic Load
M97 series
-
The new M97XX series programmable DC electronic load is a new generation product designed from Maynuo Electronic Co.,Ltd. Incorporating high-performance chips, the M97XX series delivers high speed and high accuracy with a resolution of 0.1 mV and 0.01 mA (basic accuracy is 0.03% and basic current rise speed is 2.5 A/μs). M97XX series have wide application from production lines for cell phone chargers, cell phone batteries, electronic vehicle batteries, switching power supplies, linear power supplies, and LED drivers, to research institute, automotive electronic, aeronautic and astronautic, maritime, solar celland fuel cell etc.test and measurement applications. From 150W to 200KW, there are many models to choose from :
-
Product
Multi-channel DC Electronic Load
IT8700 Series
-
IT8700 series programmable DC electronic load adopts removable modules design, supports up to 16 channels with mainframe extension transient mode up to 25 kHz, which improves your test efficiency, with high resolution and accuracy. Users can freely choose in the 8 load modules according to the number of channels and power requirements, controlled by mainframe control panel, or controlled by host computer software via built-in LAN / RS232 /USB / GPIB interface.
-
Product
600~1500W DC Electronic Loads
JT632 series
-
Nanjing Jartul Electronic Co., Ltd
JT632 series electronic load is functioned with 500KHz high-speed synchronous sampling, DSP technology, powerful dynamic test and multi-aspect intelligence analysis. All these are fully integrated into auotmatic test function, which makes JT632 series load very suitable for testing power supply when produced in large quantity. Besides, JT632 series load also possesses the features of current rising slew rate programmable, high-speed dynamic loading and programmable list function, which makes JT632 series load satisfing most of R&D requirements.
-
Product
Load Pin Products
-
DLM are world renowned for the design and manufacture of custom design load pins for a host of industries, including offshore moorings, renewable energy and marine & subsea applications.
-
Product
RF Loads
-
Bird manufactures a broad spectrum of devices from one watt to eighty kilowatts. Our resistive product portfolio includes air-cooled, water-cooled, oil-dielectric, convection cooled, and conduction cooled RF attenuators and RF loads.
-
Product
API Load Testing
loadUI NG Pro
-
With a visual, drag-and-drop interface, loadUI allows you to create, configure and redistribute your Load Tests interactively and in real-time. In a single test environment, loadUI provides complete test coverage and supports all the standard protocols and technologies. And it''s so powerful, it generates scalable, high-volume and real-world load from any number of local and remote computers. Meet loadUI, the future of Load Testing.
-
Product
Load Cell Indicator
9840
-
The 9840 is suitable for use in calibration labs, field service, or anywhere high accuracy is important. Features include a bipolar 6-digit 2-line display, remote sense, low noise, 22-bit resolution, USB port with RS232 communication, mV/V calibration and the ability to store up to 25 different sensors. 6-point linearization, unit conversion, front-panel tare. Self calibration via TEDS Plug & Play ready IEEE1451.4 compliance.
-
Product
Modular DC Electronic Load
N3300A Series
-
The new N3300A Series of dc electronic loads is fast, accurate, and ideal for increasing production throughput in high volume dc power supply manufacturing. This series consists of a full rack width (1800 watts max) mainframe and a half rack width (600 watts max) mainframe, and 7 interchangeable electronic load modules. The modules provide a variety of voltage, current and power ratings. New dc connectors for test system configurations are now available on all modules.
-
Product
Load Cell Transmitter
MODEL SST-LV
-
The SST-LV is a Plug & Play Smart TEDS IEEE 1451.4 compliant Transmitter. Just plug in a TEDS compatible Load Cell or Torque Sensor and the SST-LV will automatically self-calibrate. When used with a non-TEDS Load Cell or Torque Sensor, the SST-LV Transmitter is easily programmed using a PC with an RS232 port and Instrument Setup (IS) software, which provides a graphical user interface. The SST-LV may be powered from 12-30 Vac or 10-48 Vdc. The SST-HV Has an Isolated transducer excitation output that is selectable between 5Vdc or 10Vdc. There are Dual solid state relays and an Isolated 4-20 mA, 0-20 mA or 0-10V analog output. There are three Isolated serial data transmitter output ( RS232 , Half-duplex RS485, full-duplex RS485 ) and three serial protocols that are software selectable (Modbus RTU, Modbus ASCII and Custom ASCII). Isolation to 250V rms is provided for power, signal input, analog output, relay outputs, and communications. Isolation adds safety and avoids possible ground loops. The transducer excitation output is isolated to 50V from signal ground.
-
Product
Load Cells
-
Instron is the only testing system manufacturer that designs and builds its own load cells, ensuring exceptional accuracy, stiffness, and alignment across a wide measurement range. Produced at Instron’s High Wycombe, UK facility, each load cell is temperature-compensated and calibrated to international standards for outstanding repeatability. Backed by the largest commercial deadweight stack in the U.S., Instron’s calibration process delivers precision that often exceeds industry requirements—providing reliable, traceable performance for even the most demanding materials testing applications.
-
Product
Regenerative Power System, 950 V, 20 A, 10 kW, 200/208 VAC
RP7953A
DC Power Supply
The RP7953A regenerative power system is a single output, bi-directional, regenerative DC power supply with highly integrated safety features that protect both your people and your device under test. The regenerative capability enables the energy normally consumed to be returned to the grid cleanly, saving costs associated with energy consumption and cooling.
-
Product
Programmable DC Electronic Load
-
Programmable DC electronic load is a device that precisely regulates the load voltage and current dissipation power consumption of electrical energy. There are several important parameters to consider when choosing programmable DC electronic load, including maximum power, maximum current, maximum voltage, current slope, and so on. Each indicator is related to the needs and applications we actually test.
-
Product
DC Power Supply
PW-3032
-
*Low Ripple & Noise*30V/3A+5V/3A Dual output.*<0.4m Vrms Ripple & Noise(C.V.)*<2.5m Arms Ripple & Noise(C.C.)*Dual Display.
-
Product
DC Insulation Testing
-
Diagnostic insulation testing today represents over a hundred years of constant development. When Sydney Evershed pioneered the first insulation tests in the late 19th century, the only measurable values were insulation at 500 volts and a basic continuity check. However, measurement techniques have continuously evolved to keep pace with new insulation technologies. From electronic design and household wiring to generators and power transmission systems, all different kinds of insulation must operate at a safe minimum value.
-
Product
DC Control Tools
-
Assembly designs are getting more and more complex while production speeds continue to increase. To compete, lean manufacturers strive to complete more work with fewer tools. A single Mountz DC control tool can do the work of 2-15 regular tools, saving space and increasing production. Mountz DC control tools are easy to program and can remember up to 30 process sequences with 20 program steps. This gives you the flexibility you need to carry out varied and complicated manufacturing plans. A Swiss DC servo motor controls torque delivery with clockwork repeatability. Combined with built-in screw counters and error-proofing software, Mountz DC control tools offer supreme production results and product oversight. And by providing documented fastening results, Mountz DC control tools also make regulatory compliance easy.
-
Product
Load Banks
-
From battery discharge testing to power equipment verification, our load banks are designed for precise testing and maintenance, helping you maintain peak performance and compliance with ease.
-
Product
DC Power Supplies
Asterion DC ASA Series
-
AMETEK Programmable Power, Inc.
The Sorensen™ Asterion® DC ASA Series is the newest addition to the Asterion platform of power testing solutions. The new ASA Series features three independent, isolated 600W channels for a combined 1800W total output power. The autoranging supplies feature expanded current and voltage range at the full output power level, enabling the ability to satisfy a wider testing need without requiring the purchase of additional models.
-
Product
DC Filter Inductors
-
Osborne DC filter inductors (aka filter chokes) are commonly used in AC to DC conversion circuits to present an inductive voltage drop to the AC component of rectified current. This inductive voltage drop acts as a filter. Osborne designs filter inductors to components to function effectively (without saturation) in the presence of the DC current. Osborne will work with you to mitigate the impact of ripple frequency in conversion circuits. Every Osborne DC filter choke is designed for high performance with special consideration given to your circuit´s power supply frequency and conversion configuration.
-
Product
DC Power Supply
WPS Series
-
The WPS Series programmable DC power supply is a high-precision, wide range of voltage & current within the power rating of the power supply, full-featured high power density programmable DC Power Supplies. It can provide wide-range, low-ripple and stable DC output which is used for DC input products and components function testing and experimental simulation.
-
Product
Programmable LED DC Electronic Load
M98 Series
-
M98 series DC electronic load, as a new generation product of Maynuo Electronic Co., Ltd, is designed for the LED driver application. A special circuit is desiged for the LED driver on the base of the M97XX sereies. Incorporating high-performance chips, the M98XX series delivers high speed and high accuracy with a resolution of 0.1 mV and 0.01 mA (basic accuracy is 0.03% and basic current rise speed is 2.5 A/μs). M98XX series have wide application from production lines for cell phone chargers, cell phone batteries, electronic vehicle batteries, switching power supplies, linear power supplies, and LED drivers, to research institute, automotive electronic, aeronautic and astronautic, maritime, solar celland fuel cell etc.test and measurement applications.
-
Product
DC Bench Power
-
AMETEK Programmable Power, Inc.
From benchtop supplies to rack mounted industrial power subsystems, AMETEK Programmable Power is the design and manufacturing leader of precision, programmable power supplies. The voltage range for the AMETEK DC bench supplies is 7V to 600V and the current range is 0A to 1,000A producing a power output of 0W to 840W. Select from the models above to find the right fit for your application.
-
Product
DC Bias Attenuators
-
a fixed DC Bias attenuator from Pasternack. This 10dB attenuator is an in-line, resistive PI attenuator pad design. Our coaxial 50 Ohm attenuator is manufactured to precise RF / microwave industry specifications.
