Non-contact Voltage Testers
check for presence of electricity.
-
Product
Memory Burn-In Tester
H5620/H5620ES
-
As Server and Mobile applications have mainly led the Memory and market has also entered a super cycle that has completely withdrawn from the previous silicon cycle.Memory capacitance will continue to rise as the application of data processing and mobile communication occurs—however, revenue will not grow as ASP goes down. Suppliers need to reduce test costs and increase profits.H5620 contributes to reduction of test cost by integrating the test process of DRAM Burn-in and Core Test. This hybrid memory test solution solves the challenge of reducing test costs while increasing test efficiency in the expanding DRAM market.
-
Product
10A Continuity Tester
EQUITEST
-
EQUITEST is connected to its master unit via C2050 cable and to the mains for power supplying.Please refer to the user manual of your HT installation safety tester for the compatibility to EQUITEST.
-
-
Product
Stand Alone Low Voltage Tester
TestMate 128
-
The TestMate continuity tester features a universal interface fixture that accommodates adapter cards for quick changes in harness setups. Adapters can be exchanged in seconds to adapt quickly to any of a variety of wire-harness/cable connectors.
-
Product
Anaerobic Jar Tester
LD-LAJ-A12
-
Anaerobic JarLD-LAJ-A12with 3.5 L capacity has PMMA transparent, smooth surface jar design. High quality O-ring is used to make tight sealing between jar and lid. Adopted with quick snap-shut coupling, enables quick connection to the system in a one soft move. The number of gas packs needed may vary in brands and pack size, required to create anaerobic condition in the jar.
-
Product
Digital Safety Tester
-
Is equipped with a high-efficiency PWM amplifier, which isolates the influence of external voltage fluctuations and outputs stable high voltage. Even in areas with large voltage fluctuations, it can achieve "safe" and "reliable" measurements.
-
Product
Proving Unit & Voltage Tester Kit
DLPK1
-
Touch electrode for Quick testing of fused leads Optical and acoustic continuity Indication Low battery indication A portable, battery powered Proving Unit for testing Two Pole Voltage Testers up to 690V Continuity Tester for testing: Fuses, Fused test leads etc
-
Product
Relay Circuit Tester
RCT76
-
Quickly identify electrical problems in an entire circuit at the push of a button. Test the component on a circuit to determine if it is functioning correctly.
-
Product
Adhesion Tester
-
An adhesion tester measures the force required to detach a coating from a substrate. Often called a pull-off adhesion tester or peel tester, an adhesion tester applies a large amount of force to evaluate a coating's bond strength. When measuring peel force or adhesiveness, the nature of the substrate's surface plays a significant role. However, a high-quality adhesion tester features a self-aligning measuring head to compensate for any surface irregularities.
-
Product
Horizontal Flammability Tester
TF311
-
TESTEX Testing Equipment Systems Ltd.
Horizontal Flammability Tester, to determine the comparative burn rates and burn resistance of textiles, particularly those for automotive interior use. Horizontal flammability tester is safe and easy to operate, Comprises draft free stainless steel cabinet with observation window, sample holder and door mounted burner. Horizontal Flammability Tester complies with ISO 3795, ASTM D5132,FMVSS 302, etc.
-
Product
DC Voltage Test System
-
HIGHVOLT Prüftechnik Dresden GmbH
DC test systems are used to test components and complete systems found in electrical power supply systems and operating on DC voltage.
-
Product
0-5KV AC Withstand Voltage Tester
2670A
-
Shenzhen Chuangxin Instruments Co., Ltd.
0-5KV AC withstand voltage tester Features: High voltage,small current, high accuracy. Leakage current, testing time, continuous arbitrarily, well-adapted.
-
Product
Cable Tester
-
The MapMaster™ mini detects faults and locations of RJ45 network cables. Good terminations, causes of faults and locations of cables are displayed on an LCD display. A set of five mapping remotes is included for locating cables terminated in wall jacks or patch panels. A built-in tone generator with 4 different tone combinations can be used with a tone probe to detect where a cable is routed and the location of the end of the cable.
-
Product
Combo Tester
750USB
-
The Staticide® 750USB Wrist Strap & Dual Heel Tester measures electrical resistance of wrist straps and heel grounders simultaneously and individually. It can also do what simple pass/fail testers cannot: store the user data and actual resistance readings to a computer. Colored LEDs and a buzzer provide universally understood test results in under three seconds.
-
-
Product
LED Light Tester
-
The T100L Automatic LED Light Test Equipment is designed to identify the presence of any defects of electronic components for LED light applications, addressing any high-volume production testing challenges without needing expensive test fixtures with fiber optics
-
Product
IK Level Tester
IK07-10
-
IK ratings are defined as IKXX, where “XX” is a number from 00 to 10 indicating the degrees of protection provided by enclosures (including luminaires) against external mechanical impacts. The different IK ratings relate to the ability of an enclosure to resist impact energy levels measured in joules (J). IEC 62262 specifies how the enclosure must be mounted for testing, the atmospheric conditions required, the quantity and distribution of the test impacts and the impact hammer to be used for each level of IK rating. The IK test applicate on lighting luminaires test according to IEC60598 (GB7000) and IEC60068-2-75 (GB2423.55).
-
Product
Qualification Tester
LQ402
-
Computer Gesteuerte Systeme GmbH
The qualification tester LQ402 is designed to support up to 6 DUTs (Device under Test), for which the loads are installed in separate load boxes. The system consists out of 2 cabinets. One is for the electronic components with the primary measurement devices and the other one holds the 6 load boxes.
-
Product
Transformer Performance Tester
JYM
-
JYM insulation resistance tester is used for on-site insulation resistance measurement. The instrument has built-in positive and negative bipolar high-voltage power supplies, with large output power and strong load capacity. It is suitable for insulation resistance measurement of samples with large capacitance, such as power transformers and cables.
-
Product
Voltage Input0 to 2.5/10/25V
TGPR-0704
-
Voltage input data logger that is housed in a robust, waterproof (IP68) rated case.The TGPR-0704 can be used to record the output from a number of industry standard sensors. Common applications include pressure and windspeed monitoring.
-
Product
IEC60065 Socket Torque Balance Tester Torsion Tester
-
Shenzhen Chuangxin Instruments Co., Ltd.
*Plug and Socket Torque Tester/Device is for compliance is checked by engaging the device, as during intended use, with the socket-outlet of a test apparatus. *Plug Torque Tester/Equipment is a device provided with pins intended to be introduced into fixed socket-outlets shall not impose undue strain on these socket-outlets.The balancing arm of the test apparatus pivots about a horizontal axis through the centre lines of the contact tubes of the socket-outlet at a distance of 8 mm behind the engagement face of the socket-outlet.*With the machine not in engagement, the balancing arm is in equilibrium, the engagement face of the socket-outlet being in the vertical position.After the device has been engaged, the torque to be applied to the socket-outlet to maintain its engagement face in the vertical plane is determined by the position o a weight on the balancing arm.
-
Product
Saw Mark Tester
SRT-301
-
SRT-301 Saw Mark Tester is used to Measure Line-mark depth of the wafer surface,it has the advantages such. As easy carried, Conveniently operated Liquid crystal display, energy conservation and so on, At the same time,it has the built-in printer and rechargeable batteries , All design are up to the standards of JIS,DIN,ISO,ANSI.
-
Product
DC-DC High Voltage Power Supplies
-
DC inputs from 21.6 to 32.0 Vdc input may be used for these versatile power supplies. Although their outputs are continuously adjustable from 0 to their maximum ratings, 20-turn controls permit precise setability.
-
Product
Hydrostatic Head Tester
-
TESTEX Testing Equipment Systems Ltd.
Hydrostatic Head Tester is used for measures the resistance of a fabric to the penetration of water under hydrostatic pressure. Hydrostatic Head Tester complies with AATCC 127, EN 20811, ISO 1420A, etc. Please contact us for Hydrostatic head test procedure.
-
Product
Phase Rotation Testers
-
Our range of phase sequence indicators provide LED indicationof rotation. They are perfect for checking phase sequence in motors, pumps and air conditioning units.
-
Product
Microwave Leakage Tester
TEK500
-
An easy to use, low cost pass / fail microwave leakage detector suitable for commercial and domestic microwave ovens. It is designed to comply with national standards on permitted exposure levels. The TEK500 includes a self test which simulates a real microwave input to ensure the unit is working correctly at all times.
-
Product
Digital ELCB Tester
KM 1812 EL
-
Kusam Electrical Industries Limited
* 2 Lines x 16 Characters L.C.D.* Very Low Power Consumption.* Microprocessor Controlled.* Menu Driven.* Accurate digital readout of disconnection Time.
-
Product
Tackiness Tester
TAC1000
-
For the measurement of tackiness (instantaneous adhesive strength) of various pastes and adhesive tapes, it is possible to quantitatively evaluate the data, which until now had large errors due to individual differences. First, press the measuring probe, which is controlled (approach speed, pressure force, pressure time, separation speed) against the sample, and measure the adhesive force in the process of separating. Measured data can be processed by a computer. With double temperature control (patented), the sample piece is preheated from the back side with a hot plate and the heated probe penetrates the measurement surface, making it possible to keep the set temperature and the temperature of the test surface to be evaluated constant. Since the pressurization time can be as short as 10msec, it is possible to measure the tackiness caused by momentary contact.
-
Product
Leeb Hardness Tester
HT6561
-
Product synopsis1.1 Typical Applications* Die cavity of molds* Inspection of bearing and other mass produced parts on aproduction line* Failure analysis of pressure vessel, steam generator andother equipment* Inspection of installed machinery, permanent parts ofassembled systems and heavy work pieces.* Testing surface of a small hollow space* Material identification in the warehouse of metallic materials* Rapid testing in large range and multi-measuring areas forlarge-scale work piece1.2 Testing Features* Palm size for narrow space.* Test at any angle, even upside down.* Direct display of hardness scales HRB, HRC, HV, HB, HS,HL.* Large memory could store 250 groups including singlemeasured value, impact direction, material and hardnessscale etc.* User recalibration function allowed.* Can communicate with PC computer for statistics andprinting by the optional cable.* Manual or automatic shut down.* Low battery indication.1.3 Technical SpecificationsDisplay: 12.5mm LCD with back lightAccuracy: Display error ±0.8% at LD=900Measuring range: 200-900LConversion: HL-HRC-HRB-HB-HV-HSDMaterials: 9 different common materialsWith RS232C interfaceMemory: 250 data can be stored and re-readableImpact device: D Will handle the majority of hardness testingapplications. Weight: 75gPower supply: 2x1.5V AAA size batteryDimension: 146×65×36mmWeight: 130g (not including batteries)Working temperature： - 10℃～＋50℃Storage temperature：- 30℃～＋
-
Product
Bonding Tester
PTR1102
-
In wire bonding in semiconductor manufacturing, electrodes are joined using gold wires of several tens of microns. In order to measure the pull (tensile) strength and ball shear (shear) strength of this gold wire, this machine has load detection accuracy and fine positioning accuracy. In addition, for the measurement of high load areas such as die shear strength and solder joint strength, this machine supports measurement in high load areas while maintaining accuracy in low load areas by replacing the sensor part.
