J1
-
Product
VME J1 4 Slot with ADC Connectors
101VMEJ104-0590
-
VME J1 backplane 4 slot, compliant with ANSI/VITA 1-1994. 8-layer stripline design Includes passive termination inboard and automatic daisy chain connectors.
-
Product
VME J1 6 Slot with ADC Connectors
101VMEJ106-0590
-
VME J1 backplane 6 slot, compliant with ANSI/VITA 1-1994. 8-layer stripline design Includes passive termination inboard and automatic daisy chain connectors.
-
Product
VME J1 17 Slot with ADC Connectors
101VMEJ117-0590
-
VME J1 backplane 17 slot, compliant with ANSI/VITA 1-1994. 8-layer stripline design Includes passive termination inboard and automatic daisy chain connectors.
-
Product
VME J1 3 Slot with ADC Connectors
101VMEJ103-0590
-
VME J1 backplane 3 slot, compliant with ANSI/VITA 1-1994. 8-layer stripline design Includes passive termination inboard and automatic daisy chain connectors.
-
Product
VME Backplane
VME J1
-
VECTOR Electronics and Technology, Inc.
Vector offers wide range of VME backplanes from 3 to 21 slots wide in J1 and J2 are 3U backplanes. All VME backplane boards are constructed from FR4 epoxy glass material and are assembled and tested. Press fit connectors are used throughout on all sizes.
-
Product
VME Type 32 with 6U, 5 slot Backplane
32V05MMX36N3V10
-
VME Type 32 with 6U, 5 slot Backplane J1, J2.
-
Product
Single Rear Slot Universal ISA plug-in PCMCIA Adapter
J105
-
* High reliability 68 pin PCMCIA compliant,* static protected, connectors with card eject buttons are used.* Standard Types I, II and III cards,* 5V cards supported.* Operating temperature range: 0-50 C* ISA board dimensions: 150 x 100 x 24mm Host Computer:* Any true compatible Pentium PC or higher with ISA Bus.
-
Product
Mini Logger
J1939
-
The DAWN J1939 Mini Logger™ is a compact logger that acquires CAN bus data from heavy-duty trucks, buses, and off-road vehicles. It fits directly on the J1939 connector. The J1939 Mini Logger is part of the Mini Logger family of compact, low-cost, data loggers that acquire a variety of data from trucks and cars.
-
Product
Simulators (Gen II)
J1939
-
The Au SAE J1939 simulators (Gen II, includes V1.00A releases and V2.00A releases) can generate SAE J1939 signal for up to three controller applications (CA): Engine, ABS and Transmission. Au J1939 simulators are designed so easy to use, even product line operator and sales personal can use them without Controller Area Network training. Au J1939 simulator can run all by itself and doesn''t require complicate software settings or user''s knowledge and experience on Controller Area Network. It is widely used as valuable tools for any situation from product-line test, incoming inspection, business demonstration to product development and product validation.
-
Product
Basic Quad J-Type Analog Thermocouple Amplifier
SEN-30103-J1
-
Analog thermocouple amplifier board based on the AD849x from Analog Devices (successor of the AD597). This quad-channel thermocouple board converts the very low voltage signal from a thermocouple to a highly-linear, 0.005V/C output with either 0V or 1.245V offset (both configurations stocked) while removing unwanted noise from the signal. Many supply and output configurations are available with this board, though the PCB was designed with Arduino in mind. Specifically, the output header will plug directly into a standard Arduino Uno or Mega, with a pin-for-pin match for power supply, ground and analog outputs. With a 5V Arduino, temperatures from 0C to 1,000C are possible with the 0V offset board and -249C to 750C with the 1.245V offset board. If using a 3.3V microcontroller (Due, etc), the board must be supplied with no more than 3.3V to avoid damaging the microcontroller. Temperature measurement range is dependent on the supply voltage. It is possible to supply the board with higher voltages to allow temperature measurement over the entire operating range of the K-Type and J-Type thermocouples, allowing use with more capable data acquisition equipment.
-
Product
3U VME J1 Classic 10-slot With 70A M4 Power Bolts
50510-210-0000
-
3U VME Bus J1 Classic Backplane 10-slot, VITA, termination passive inboard, daisy chain automatic active, power connection 70A power bolts, I/O pins 13mm gold-plated, shroud (1P1) without latches
