Current Shunts
Resistors with known accurate values to measure current.
See Also: Shunts, AC Current Shunts
-
Product
Through Hole Type AC Current Sensor
CTF-200B
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*For AC current and power measurements.*Suitable for current measurements of main cable.*Measuring range:AC 1A～200A.
-
Product
Current Probes
-
Teledyne LeCroy current probes do not require the breaking of a circuit or the insertion of a shunt to make accurate and reliable current measurements. Based on a combination of Hall effect and transformer technology, Teledyne LeCroy current probes are ideal for making accurate AC, DC, and impulse current measurements.
-
Product
100A, 2 MHz, DC/AC Current Probe, BNC, 100A Peak, 70A rms, 1 meter cable
T3CP100-2
-
100A, 2 MHz, DC/AC Current Probe, BNC, 100A Peak, 70A rms, 1 meter cable.
-
Product
Split type Pulse Current Sensor
OKM-03
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
For pulse current detection.
-
Product
GAOTek Portable H/L Voltage Clamp Current Leaker
GT00YA00ZX
-
The GAOTek Portable H/L Voltage Clamp Current Leaker measures high voltage current with a 12.5 in (32 cm) insulating rod, adopting the latest CT technology and integrating mask digital technology. This instrument provides high precision, reliability, and stability with its integrated design between transducer clamp and domain. This leaker can be used to measure any wire with or without the insulation layer where the voltage is below 10 kV. The insulating rod is portable, moisture resistant, heat resistant, shock resistant, and insulating. It provides additional functionalities such as online current testing, peak and data holding, data storage, detection of high and low current in primary and secondary circuits separately, and provision of suitable calculations to conclude change in high and low pressure.
-
Product
1000 Amp High Accuracy Current Probe
HA1000
-
The HA1000 is our most accurate current probe. The HA1000 clamp-on current probe measures from 1 to 1000 amps AC.
-
Product
High Current Probes
-
*Low internal resistance to minimize arching*PogoPlus bias ball design*High current optimized base material and plating*Higher temperature spring design*Specialized high current tip geometry
-
Product
Current Probe With Hall Effect Technology
CP 35
-
The CP 35 current probe has been designed for use with oscilloscopes respectively for accurate, non-intrusive measurement of AC, DC and complex waveform currents.
-
Product
Current Detectors
-
On our website you will find current detectors that are ideal for measuring AC or DC voltage. Current detectors are irreplaceable for inspection work and maintenance. We offer the following: voltage detectors, voltage leak detectors, voltage power detectors, Current clamps ideal for measuring AC or DC voltage. metric detectors, current detectors and more. These high quality current detectors include the capacity to measure many other parameters, such as capacity, resistance, power (both by way of clamps or by means of a hand held digital device with external clamps with a range of one or three stages). The current detectors are like the majority of our measurement instruments in that they meet and excel ISO standards. This calibration is done in a laboratory and comes with an accompanying certificate. All of our current detectors can perform the demanding tasks in each industrial sector regardless of the technical problem you encounter. If you can't find the current detectors you are looking for, please contact us and we will help you find the best solution to suit your needs by calling our offices on: UK customers +44(0) 23 809 870 30 / US customers (561) 320-9162 and our technical staff will advise you regarding our measuring instruments. Our engineers and technicians will be happy to help you with the current
-
-
Product
Leakage Current Tester
-
Aarohi Embedded Systems Pvt. Ltd
“ AAROHI” make Leakage current tester is very compact & specially designed microprocessor based instrument to measure mA of motor,Stator.
-
Product
Through Hole Type AC Current Sensor
CTF-400B
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*For AC current and power measurements.*Suitable for current measurements of main cable.*Measuring range:AC 1A～400A.
-
Product
Leakage Current Tester
2675
-
Shenzhen Chuangxin Instruments Co., Ltd.
RK2675 series Leakage Current Tester is used to measure the electrical insulation quality and products’ safety performance of the main indicators.
-
Product
High Current IC Test
-
C.C.P. Contact Probes Co., LTD.
Our patented probe design allows very high currents of up to 5 Amps
-
Product
Clamp type AC Current Sensor／for Low Leakage Current Measurements(ZCT Series)
ZCT-22
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Best sensor for leakage current measurements*Ultra compact size*AC 1mA～100A
-
Product
High Current SMU
-
Source and Measurement Units (SMUs) are devices that generate voltages or currents and can measure them simultaneously using the integrated measurement units (VMU, CMU).High current SMUs operate as a regulated power source and are able to generate very high output currents as pulses.
-
Product
Digital Current Integrator
-
The ORTEC Model 439 Digital Current Integrator was designed to accurately measure DC currents or the average value of pulse currents such as produced by accelerator beams. It digitizes the input current by producing an output pulse for specific values of input charge. A front-panel switch permit the selection of three different amounts of charge (10–10, 10–8 or 10–6 coulomb) required to produce an output pulse. The instrument has a digitizing rate from 0 to 10 kHz to provide wide dynamic range on each setting and high-resolution readout without meter interpolation.
-
Product
AC Current Sensor
LFR
-
The LFR ac current probe has been designed to have market leading low frequency performance, meaning low phase shift and low noise. This compact, low cost, clip-around probe is both flexible and dual-range, and is optimized to give minimal phase measurement error at frequencies from 45Hz to 20kHz and have a very low noise floor.
-
Product
Current Measurements of PWM or Inverter, AC/DC 25～500A, φ35mm
CTF-500DC
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*AC/DC 25～500A*Current measurements for PWM or inverter
-
Product
PXI/PXIe Wide Current Range Multiplexer Module, Dual 6-Channel, 2-Pole
42-514-104
-
The 40-514-104 (PXI) and 42-514-104 (PXIe) are low density multiplexers in dual 6-channel, 2-pole configuration. They are capable of switching a wide range of current, from 10 μA to 2.5 A at 220 VDC/250 VAC. The current capability of the module permits the use of a single module type for both low and medium current test applications.
-
Product
High Accuracy 100 Amp Current Probe
HA100
-
The HA100 is a compact clamp-on current probe for smaller loads where compact size is important. Its measurement range is from 0.1 to 100 amps AC and is very small which is ideal for locking inside a crowded electrical panel during monitoring.
-
Product
High AC Current Capacitor
LC1/LC2/LC3-RNM
-
Induction Heating Processing Equipment, Electric Current Welding, High Power Resonant Circuits, Motor Controls; Oscillating, Bypass, Coupling circuits, High AC Current applications, High-Frequency AC Filter and Medium Frequency Power applications.
-
Product
Split Core Hall Effect DC Current Sensor
CYHCT-C2TV
-
ChenYang Technologies GmbH & Co. KG
This Hall Effect current sensor is based on open loop principle and designed with a split core and a high galvanic isolation between primary conductor and secondary circuit. It can be used for measurement of DCcurrent etc. The output of the transducer reflects the real wave of the current carrying conductor.
-
Product
Rogowski AC Current Probe
RCP500
-
Shenzhen Micsig Instruments Co., Ltd.
Adopts the Rogowski coil current measurement system: within the range, the output signal of the system and the current signal to be measured are always linear, so the accuracy will not change with the current; The RCP500 measures AC current up to 500A pk, minimum to 200mA pk, with bandwidth ranging from 15Hz to 300KHz, 1% accuracy, and has less than 2mV noise. Directly powered by Micsig UPI interface, realise auto scaling setup,
-
Product
Portable Voltage and Current Instruments
-
Each model in our portable test equipment range is designed for accuracy and reliability, providing high performance and ease of use for applications. Products are used in various lab and field applications across industries such as research and development, semiconductor, and process control. For higher range electrical source and measure we have a series of bench multifunction calibrators and multimeters.
-
Product
Current Injectors / Relay Testing
RTS series & SC-10
-
UDEYRAJ ELECTRICALS PRIVATE LIMITED
Ranges: 1A to 200A AC, Auxiliary output AC / AC+ DC, TRMS Digital metering.
-
Product
AC / DC Current Probe, 2 MHz, 500 Arms
N2780B
-
The N2780B current probe is an accurate and reliable solution for measuring AC and DC currents. Using a hybrid technology that includes a Hall effect sensor and an AC current transformer, the probe provides accurate measurement of DC or AC currents up to 500 Arms continuous.
-
Product
12-Channel VME Current Loop/Process Control I/O Module
V220
-
The V220 is ideal for driving and sensing transducers in computer or PLC-based control systems. It can also be used to simulate complex industrial processes to control systems under development and certification.
-
Product
Non-destructive Eddy Current Testing of Long Products such as Tubes, Rods, Wire, and Profiles
DEFECTOMAT® Product Familiy
-
Foerster Instruments, Incorporated
The DEFECTOMAT systems by FOERSTER were specially developed for quality testing and process monitoring of long products. From hot testing to all bright steel processing steps, the surfaces of semi-finished products made from austenitic, (non) ferromagnetic metals can be tested for defects. The DEFECTOMAT systems operate in a contactless and non-destructive manner in accordance with the eddy current method and are used for detecting short defects, such as holes or localized defects and transverse defects. The systems detect defective materials fully automatically and reliably. Defects can be marked, classified, and automatically discarded. the test speed of up to 150 m/s facilitates 100% testing, even at high production speeds. The systems benefit from low operating costs and frugal energy consumption as well as low maintenance costs, few wear parts, and low use of materials.
-
Product
Mini AC Leakage Current Clamp Tester
M-104+
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
・33mmφCT window and ultra compact size.・Data-hold function. Especially useful when working in dark or hard to get areas.・Low cost type, Core shielding is not equipped.
