Fault
-
Product
Test Module
FailSim
-
FailSim simulates a faulty component and allows the user to quickly and simply improve the actual fault detection of a test program. The result represents a definitive conclusion for tested or untested components.
-
Product
Vehicle Multiprotocol Interface Module
C Series
Interface
C Series Vehicle Multiprotocol Interface Modules use hardware-selectable NI-XNET Transceiver Cables (TRC) to communicate High-Speed/Flexible Data‑Rate CAN, Low-Speed/Fault Tolerant CAN, and/or LIN. Using the NI-XNET driver, you can create applications that require real-time, high-speed manipulation of hundreds of CAN and/or LIN frames and signals. The NI-XNET device-driven DMA engine enables the onboard processor to move frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time. C Series Vehicle Multiprotocol Interface Modules work well in applications such as hardware-in-the-loop (HIL) simulation, rapid control prototyping, bus monitoring, and automation control.
-
Product
Universal Locator
UL 30
-
Cable fault location with the BAUR UL 30. The UL 30 receiver is used together with a ground microphone (BM 30) and a surge voltage generator (SSG, STG) to pinpoint cable faults. With the coil integrated in the BM 30 for runtime measurement, the device determines the time difference between the magnetic and acoustic signal. This particularly offers special advantages when d ealing with faults difficult to locate acoustically.* Built-in speaker* Splashproof design* Large, illuminated display* Lightweight
-
Product
ATPG with Embedded Compression
TestKompress
-
TestKompress is an automatic test pattern generation (ATPG) tool that provides the highest quality scan test with the absolute lowest test cost. TestKompress has an industry-proven ATPG engine that applies effective fault models to your entire logic design. Manufacturing test costs are held in check by an award-winning test pattern compression technique called Embedded Deterministic Test (EDT).
-
Product
Visual Fault Locator ( VFL)
TM315N
-
The TM315N Economical VFL is an efficient and low cost basic fiber test tool, it provides a visible way to find fiber faults and identify fibers in an optical network during and after installation.
-
Product
Time Domain Reflectometer
ETDR 10A-1
-
Compact dual channel precision full function portable easy to useTDR for fault location on balanced unloaded cables.
-
Product
Power-off Circuit Board Testing
Huntron® Trackers®
-
Adding diagnostic tools to enhance your circuit board test capabilities is an important part of any electronic repair environment.Huntron Tracker power-off circuit board test uses analog signature analysis to detect and isolate component faults on boards beyond power-on functional testing. By comparing Tracker signatures from a working circuit board to the signatures of a non-working board, you can troubleshoot down to the component level.
-
Product
PXI 10A Fault Insertion Switch 6-chan 2-bus
40-192-012
Fault Insertion Unit
This PXI fault insertion switch uses solid state switching elements and is capable of switching current up to 10A. It is designed to be able to insert three different fault conditions between the test fixture and the equipment under test: Open-Circuit. Short-Circuit between UUT connections. Short-Circuit to external signals. Through relays on each channel enable signals to the UUT to be set open-circuit. Fault Insertion Buses allow any channel to be shorted to any other channel and also enable any channel to be connected to an external signal such as Power, Ignition or Ground to simulate fault conditions. The module is supplied with 2 fault buses.
-
Product
PXI-8513, 1‑Port, Software-Selectable PXI CAN Interface Module
780688-01
CAN Interface
1‑Port, Software-Selectable PXI CAN Interface Module—The PXI‑8513 is a software-selectable Controller Area Network (CAN) interface for developing applications with the NI‑XNET driver. NI‑XNET Software‑Selectable CAN Interfaces offer the best flexibility for CAN development with onboard transceivers for High-Speed/Flexible Data‑rate, Low-Speed/Fault Tolerant Single Wire CAN as well as any external transceiver. The PXI‑8513 excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals, such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The NI‑XNET device-driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts.
-
Product
Power Dividers & Splitters
-
Keysight dividers and splitters are used in a wide range of applications, such as: transmission line fault testing, power combining, source leveling, ratio measurements, power splitting, and critical signal processing applications that require minimal insertion loss and high port isolation.
-
Product
OTDR Tester
M-OTDR-502
-
Fuzhou Metricu Technology Co Ltd
Optical Time Domain Reflectometer Wavelength 1310 / 1550nm, max test range 150KM, Dynamic range 28 / 26dB, SOR standard data saving, create PDF/EXCEL format report, stable laser source, support CW/270/330/1000/2000Hz, Test fiber's length, loss, attenuation parameters and event map, locate connection point/fusion point, Automatic analysis of various linkers/fusion points, easy analyze of various events,Support saving curves number ≥30000pcs, loss test, detect the optical or optical components loss value, etc. Test IP camera, optical power meter, visual fault locator, RJ45 cable TDR test, cable tester, cable tracer, etc.
-
Product
Time Domain Reflectometer
TDR-420
-
TDR-420 is a hand held Time Domain Reflectometer designed to identify and locate faults in power, telecommunications and teletechnical cables. TDR-420 reflectometer allows to measure the length of the cable and determine the distance to damage or impedance variation in the range of 4 m to 6000 m in conductors with metal wires. The shortest measuring range of 7 meters and a dead zone of 0.6 meters allows to locate damages at a very close distance from the place where the device is connected.
-
Product
Fire Extinguishers Testing Equipment
-
The circular electrode brush passes easily through the neck of the extinguisher cylinder and then expands to make reliable contact with the lining. Faults are detected by the voltage jumping from the electrode to the earthed shell, causing an alarm to sound. Special electrodes are available specifically for this application.
-
Product
Multi-Channel Telemetry
-
The AT7000 multi-channel systems can combine any customized mix of ordinary sensors: strain gages, thermocouples, RTDs, accelerometers, as well as motor/generator field voltages, currents and ground fault currents. The received data is continuously streamed to the user as analog (+/- 10V or 4/20mA) or digital data.
-
Product
High Resistance Neutral Grounding Devices
-
HRG systems limit the fault current by placing high resistance between neutral point of transformer (or generator) and ground. As it is not possible to locate the fault point in delta connected systems, an artificial neutral point is created and delta connected system can be grounded. This allows a fault current of a few amperes thus locating the fault point gets easy. When the neutral point is grounded thru high resistance, both continuity of operation is provided during fault condition and sufficient current (typically between 2 A and 10 A) flow is provided for ease of locating the fault point.
-
Product
Thermal Shock Environmental Test Chamber
-
Guangdong Bell Experiment Equipment Co.,Ltd
DGBell’s Thermal Shock Chamber provide the sudden temperature changes between extreme cold and extreme hot from -65℃ to 150℃ (customized available), specially for environmental stress screen test of the industries that rely on thermal testing, such as component, board electronic assemblies, defense, material stress, consumer products etc. The thermal shock test can cause faulting or cracking by the expansion and contraction on the products, indicates the hidden manufacturing defects. Bell’s Thermal Shock Chamber ensure you to launch qualified product to the market.
-
Product
Transformer Protection
-
Schweitzer Engineering Laboratories, Inc.
Transformer protection products and systems provide complete primary and backup protection for all types of transformer faults. They are suited for use in utility-, industrial-, and commercial-scale power transformer systems.
-
Product
Plastic Fabrications Testing Equipment
-
PD and PHD Pinhole/Holiday Detectors have an alarm circuit to alert the operator when a fault has been located and the required test voltage can be set on the unit's meter. Spark Testers provide an inexpensive means of testing but have no output voltage meter or audible alarm. However, they can test joints even if the backing is not connected.
-
Product
Volt Gradient Detector
-
K&S Engineering and Scientific Ltd
The Voltage Gradient Unit is used to pinpoint faults by the pool of potential methods
-
Product
Cable & Antenna Analyzer
iVA Series
-
VSWR, Return Loss Measurement & Distance to Fault. The iVA Series Cable & Antenna Analyzer is an exciting new product from Kaelus that enables users to accurately measure VSWR/return loss and the location of the VSWR/return loss faults in their RF infrastructure. The wireless connectivity allows unprecedented measurement flexibility and opens up new & important possibilities in sweep testing and multi-port testing.
-
Product
Four Zone Control Module
IN042
-
The IN042 is a four zone input module designed for use with two-wire field devices such as smoke or heat detectors, pull switches and manual callpoints. It is designed to monitor these devices and provide both status indication and fault / alarm outputs for each zone.
-
Product
6 PCS Deluxe Light Set
3606
-
Peaceful Thriving Enterprise Co Ltd
Kit packed in a deluxe blow mold case.Quick, efficient and economic way to find faults find on the following electronic fuel (EFI) system:1. 3405-BOSCH PFI2. 3410-GM TBI3. 3411-FORD TBI4. 3412-GM PFI5. 3413-GEO TBI6. 3414-GM SCPI.
-
Product
4 Digit Angle Position Indicator (API)
TA-900
-
This has been the New standard in Angle Position Indicators. 4 digit API has fault monitoring for both low-level and loss of signal (LOS) and this status is shown on the front panel led. The unit provides simultaneous connection of both synchro and resolver devices.
