Development Boards
See Also: Development, Software Development, Developers, Test Development
-
product
Termination Board
MSTB 009
The MSTB 009 a-Series Analog Termination Board allows quick and secure connection of discrete wires to Data Acquisition Processors. It is the only analog termination board that may be used with the DAPs listed at the bottom of this page.
-
product
PC/104-Plus Board
PCI-P104-ADAP
Model PCI-P104-ADAP simply allows for the installation of a PC/104-Plus or PCI-104 board into any Universal PCI, 3.3V or 5V slot. It is a standard PCI bus card that supports 32-bit wide data transfers to and from a PC/104-Plus board. This allows any user the convenience of hardware testing, software development, and debugging of a PC/104-Plus board in a PC environment.
-
product
Smart GPIB Serial Interface Board
Model 4806
* Provides GPIB-to-serial and serial-to-serial data paths for serial devices with RS-232 signals.* Provides all IEEE-488.2 functions and the Status Reporting Structure.* Smart firmware automatically passes GPIB data to serial device.* SCPI commands set serial configuration, GPIB address and user's IDN message. • On board voltage regulator for operation from 5 to 15 Vdc power. • Rear panel mounting eliminates cables.
-
product
PXI Express High Speed Optical FPGA Board
HSS-8324-DSP
The Conduant HSS-8324 FPGA board provides a user programmable hardware platform that is able to sustain full-duplex high-bandwidth transfers through its 8-lane Gen3 PXI Express (PXIe) interface and its two 12-lane HSS interfaces while performing complex calculations. The PXIe interface provides a theoretical maximum throughput of 8 GBps (simultaneous in and out) while each HSS port (12 lanes up to 16 Gbps per lane) supports a full duplex transfer at theoretical rates over 190 Gbps.
-
product
6U CompactPCI® PCI Carrier Board
MIC-3961
The MIC-3961 is a 6U CompactPCI® PCI carrier board that allows users to attach a 32/64-bit PCI card via a J1/J2 connector to a CompactPCI platform. The hold-down bracket secures the PCI card onto the carrier board and protects it against vibration and shock. In addition, the bracket allows a cable to be routed through the front slot panel.
-
product
4K Autofocus MIPI NVIDIA® Jetson TX2 Camera Board
E-CAM132_TX2
e-CAM132_TX2 - 13MP Autofocus Jetson TX2 camera board is a 4-lane MIPI CSI-2 camera solution for NVIDIA® Jetson TX2 developer kit. This camera is based on 1/3.2" AR1335 CMOS image sensor with advanced 1.1µm pixel BSI technology from ON Semiconductor® and an integrated high-performance image signal processor (ISP) that performs all the Auto functions (Auto White Balance, Auto Exposure control). e-CAM132_TX2 is a two board solution consists of a base board and a 13MP autofocus camera board. This camera board is connected to the base board using 30 cm micro-coaxial cable.
-
product
PXI Express Board Virtex-5 DAC Module1GHz, 14-bit DAC
SMT781
Sundance Multiprocessor Technology Ltd.
The SMT700 module uses a Xilinx Virtex 5 LXT or S XT to implement the interfaces the board provides. The FPGA can be configured either via the onboard flash, or through the Xilinx JTAG header.
-
product
6U Processor Board
VP62105
LinkedHope Intelligent Technologies Co.,Ltd.
VP62105 supports up to 3615QE, an Intel® 4-core processor. The 3rd generation Intel® Core™ i3/i5/i7 processors have a completely new microarchitecture, enabling small-sized designs to be created with unmatched computing power, graphics performance and energy efficiency on a small footprint.VP62105 provides 4 Serial RapidIO (SRIO) x4 links for VPX Data Plane communication, 2 PCI express x8 channel for VPX Expansion Plane communication and 4 Gigabit Ethernet for VPX Control Plane communication. The rich data interchange options enable potential customers a much easier integration path for box level or system level solution designs.
-
product
LabVIEW Professional Development System
ntegrate hardware from a variety of measurement instruments and devicesIntuitive graphical programming syntax to simplify automationBuild custom user interfaces for engineering applicationsBuilt-in algorithms for signal processing, analysis, math, and PID controlSoftware engineering tools to debug, validate, and deploy codeOne-year SSP membership for technical support, online training, and software upgrades
-
product
Programmable Resistor PXI Board
GX1164 Series
The GX1164 is a 3U PXI programmable resistor module with 4 channels of 16 resistors each or 8 channels of 8 resistors each. The module is available in various resistance ranges and resolutions.
-
product
Configurable 3U CPCI Multifunction I/O Boards
Optimized to deliver unusually high-function density, high resolution / accuracy and low power consumption for rugged defense, commercial aerospace, and industrial applications, NAI’s intelligent 3U CompactPCI cards can often operate as standalone systems, eliminating the need for a Single Board Computer (SBC), operating system and associated software royalty costs.
-
-
product
6U Single Board Computer
VP62006
LinkedHope Intelligent Technologies Co.,Ltd.
VP62006 is a 6U VPX single board computer designed by LinkedHope® based on Intel® QM87 chipset. The compact and space-saving processor board meets the VITA46.0 specifications. There are SATAIII, USB3.0, Gigabit Ethernet, PCIe3.0 and Keyboard/Mouse interfaces on the board. VP62006 supports 64GB SSD, facilitating the operating system installing.
-
product
Single Board Computers
SBC35-CC405-3845
Industrial embedded computer with Quad-Core Intel® Atom™ E3845 CPU, Dual Ethernet, Dual MiniPCIe, USB 3.0, RS-232/485/422 and two independent displays via DisplayPort, LVDS and/or Analog VGA.
-
product
Type 39 E-Frame Development Platform, 2 Slot 6U VPX
39E02PSX94Y2VCEX
The Type 39 E-Frame test platform supports 6U or 3U VPX based system development. With a rugged aluminum construction, the versatile concept chassis design allows easy access for test and system architecture development for up to 12 slots.
-
product
Quad QSFP28/QSFP+ FMC+ Module
iWave’s QSFP28/QSFP+ 2×1 Stacked FMC+ HSPC Module is designed to meet VITA 57.4 FMC+ Standard. This FMC+ Module is supported by two stacked QSFP28/QSFP+ ports(Upto400G) with 4-Bit Silicon Labs programmable clock synthesizer (default = 156.25Mhz). A flexible reference clock for on the QSFP28/QSFP+ 2×1 Stacked FMC+ Module is fully programmable over the 0.16 to 710 MHz range through I2C. Each QSFP28/QSFP+ ports are directly connected to four multi-gigabit serial transceivers banks of Vita 57.4 compliant carrier Board.
-
product
Timing Board #2
TIO-10 #2
Interface board for converting signals on a National Instruments PC-TIO-10 timing board to and from fiber optic signals. This board is similar to the Fiber Optic Interface to National Instruments TIO-10 Timing Board #1 only it has more channels connected to fiber optic transmitters and receivers.
-
product
6U OpenVPX Multi-function I/O Board
67C3
NAI's 67C3 is a 6U OpenVPX Multi-function I/O and Communication Board with six function module slots that can be configured with a variety of I/O and communication functions. Additional enhancements include FIFO data buffering for select modules. Using multiple DSPs, the enhanced motherboard enables higher processing power and dedicated pre-processing control for each module.
-
product
Product Test & Measurement Development Software tools
Tequra Requirements
Tequra is a suite of software tools for product test and measurement which enables organisations to develop high-quality solutions faster, simplify support and maintenance, and facilitate continuous improvement.
-
product
ISA Digital IO Board
MS 1804
*Discrete Input / Output 48 Channels*TTL Pulse measurement channels (Timers / Counters) 12 Channels*TTL Pulse Generation 12 Channels*Bi-directional Bus 16 Bit*The Pulse Generation Frequency from 10Hz to 40MHz*The no. of pulses controlled from 1 to 255 pulses*All Channels are compatible with 5V TTL / CMOS*All the pulse input and the output signals and Bi-directional write signals driven through Pin Driver*Standard ISA Bus Interface*Driver interface for Windows2000/XP/VISTA and LINUX OS
-
product
PCI Data Acquisition Boards
Ultraview''s PCI data acquisition add-in cards are complete data acquisition (A/D) and control (D/A) systems on a single PCI Bus card. Ranging in speed from dual 14 and 12-bit 1-25MSPS boards up to 1500MSPS 8-bit boards with 8GB/16GB of on-board RAM. All cards come with graphical waveform viewers, example user programs (source code included) and device drivers for Linux or Solaris, allowing users to quickly prototype and develop their applications.
-
product
I/O Input/Output Board
VME-4514A
The VME-4514A Analog I/O (AIO) Board provides 16 high-quality analog output channels which can be programmed with on-board jumpers to operate in a variety of voltage ranges. Each output can source or sink 10 mA at ±10 V. For off-line testing, the analog outputs can be disconnected from the I/O connector.
-
product
I/O Board With Two COM, Four USB 2.0 And Audio For PICO880, PICO500, PICO300
AX93292
*Specifications: 1 x RS-232/422/485, 1 x RS-232, 4 x USB 2.0, 1 x Audio (MIC-In/Line-out), 1 x Power On, 1 x Reset, 2 x LED*Dimensions: 118 x 29 mm*Compliant products: PICO880, PICO500, PICO300
-
product
3U PXI Express Board
SMT709
Sundance Multiprocessor Technology Ltd.
The SMT700 is one of the first of a new range of Sundance cards that includes a direct connection to SLB (Sundance Local Bus) compatible mezzanine card, without the need for a Sundance TIM. This enables a variety of cards to be added to a system, for example extra Ethernet ports, video in/out, High speed ADC / DAC etc. Data from these extra cards (along with data from the SMT700’s own inputs – up to 1Gb/s Ethernet, 2.5Gb/s optical links, and RSL links) can be processed via the Virtex 5, or by another linked card or module.
-
product
Interface Board for Gigabit Ethernet
40-965-910
The 40-965-910 is a converter card for the 40-201 Ethernet/AFDX Fault Insertion Switch. Adapts the 78-Pin D-type connector on the front of the module to 4 RJ45 sockets and one 9-way D-type connector for fault signals. Allows the fault insertion testing of Gigabit Ethernet signals.
-
product
Aerospace System Development
For more than ten years, TechSAT provides to its customers research and development services for safety critical systems, primarily in electron-mechanical and avionics domains. At System Level we offer ARP4754A and ARP4761 compliant development including System Specification, Safety Assessment, System Architecture Design, Model based Validation, System Integration and Verification as well as certification support for Part 23 and Part 25 programs.At Equipment Level TechSAT offers customer specific LRU development including all elements of the development life cycle from conceptual design, through formal requirement based engineering, hardware and software development compliant to DO254, DO178, verification and validation including DO160 environmental qualification up to a DAL A certifiable product.
-
product
Rapid Prototype Development
Have time to market pressure and need to get a system or assembly or production line up and running quickly? Need to rapidly build out a solution, but don’t want to spend months on building up an architecture? Allow our rapid prototyping team to assist you – whether it is crafting 3D printed mechanical assemblies or a building up a high speed IO interface, you are in very capable hands with the ARC engineering team. Our DSX product, can help support your IP, implement your process or and be the core processing engine for your design, or if a larger system, DSX could be an integral part of your system. PVS, another tool that can help error-proof your assembly process, is ready to go in a flexible, software-centric solution that you can be reconfigured as needed to meet your changing demands.
-
product
Board
Arduino Mega 2560 Rev3
The Arduino Mega 2560 is a microcontroller board based on the ATmega2560. It has 54 digital input/output pins (of which 15 can be used as PWM outputs), 16 analog inputs, 4 UARTs (hardware serial ports), a 16 MHz crystal oscillator, a USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get started. The Mega 2560 board is compatible with most shields designed for the Uno and the former boards Duemilanove or Diecimila.
-
product
CableEye Generic Surface Mount & TH Board | Cable & Harness Tester
CB51
CAMI Research Inc. (Acton, MA) announces another new board for its CableEye cable and harness testing systems. Populated with solder pads to accept both aligned and staggered, 1.25mm and 1.5mm pitch, surface mount and through hole (TH) connectors, the board addresses any market with a demand for board-to-board connections. Rated to 700Vdc/500Vac, the CB51 may be used on all CableEye models.
-
product
Mini-ITX Embedded Board with 8th/9th Gen Intel® Core™ Desktop Processor
AmITX-CF-G
Targeted at gaming customers and system integrators, AmITX-CF-G is a Mini-ITX board specially designed for Gaming. AmITX-CF-G features GLI compliance, easy and flexible configuration, security enhancements, and system resilience. The values of AmITX-CF-G include amplified visual impact, guaranteed system integrity, secure transactions with fast TTM and low TCO, and maximized system uptime. AmITX-CF-G can satisfy application function requirements and meet GLI certification which cannot be offered by other conventional Mini-ITX boards.
