Development Boards
See Also: Development, Software Development, Developers, Test Development
-
product
Test Board For QSFP28 Transceiver
EQSFP28
The OPTELLENT EQSFP28 is a cost-effective and convenient test board for testing QSFP28 optical transceivers in R&D and manufacturing environments. The EQSFP28 is equipped with high quality RF connectors for data signals and test points for low frequency control and status signals. The EQSFP28 is equipped with power supplies to enable voltage margining. Key status signals are displayed using LED indicators.
-
product
SPARK 3U VPX Development System for Cobalt, Onyx, Flexor, Jade and Quartz Boards
Model 8267
- 9-slot, 4U 19-inch rackmount,12-inch deep chassis which houses 3U VPX Boards- 64-bit Windows® 7 Professional or Linux® workstation- Intel® Core™ i7 3.6 GHz processor- 8 GB DDR3 SDRAM- ReadyFlow® drivers and board support libraries installedOut-of-the-box ready-to-run examples
-
product
PCI Express A/D Board
AD8-3000 Series - Dual 8 bit, 3 GS/s
The AD8-3000 series has one or two 3000 MS/sec 8-bit ADCs, 8GB of on-board memory and the ability to transfer data directly into the host computer's memory at over 1 GB/sec. Streaming to the host computer can be performed simultaneously with acquisition to on-board memory, increasing the effective acquisition length by using the host computer's memory. Dual channel boards sample concurrently at twice the input clock frequency, and can also be software selected to run in single channel mode, providing twice the effective memory depth.
-
product
Product Test & Measurement Development Software tools
Tequra Requirements
Tequra is a suite of software tools for product test and measurement which enables organisations to develop high-quality solutions faster, simplify support and maintenance, and facilitate continuous improvement.
-
product
Noise Board
332D-11 VG
This printed circuit board was designed to original specifications and contains OEM specified parts. This board is required for testing the 332D-11 series gyros. Also contained on board is the Method A type calibration and sample and hold circuits required to perform the calibration of the noise circuits.
-
product
Evaluation Board
emPower
SEGGER Microcontroller GmbH & Co. KG
The emPower eval board provides a comprehensive set of SEGGER's middleware products, accelerating the start of any embedded project. SEGGER's embOS real-time operating system is at the heart of the evaluation. Furthermore, evaluation versions of the file system emFile, graphics library emWin, emUSB Host & Device, and TCP/IP stack embOS/IP (including web server demo) enable full use of the available emPower peripherals. emPower also features a J-Link OB, an on-board version of SEGGER's market-leading debug probe J-Link, which includes drag & drop programming and COM-Port support. There are three expansion interfaces to easily connect additional modules. Each connector provides I2C, SPI, UART, GPIO/timer, analog input and power. A display adapter connector enables the connection of small TFT displays. The emPower board is powered by USB only. Current consumption drawn strongly depends on the application and connected peripherals. Idle consumption is approx. 85 mA.
-
product
Embedded Vision Board
Axiomtek's embedded vision board series is designed to focus on vision inspection, guidance, measurement and identification applications. The scalable embedded vision boards help system integrators with easy customization and shortening the product development cycle while helping them speed up the time-to-market process to gain a competitive edge.
-
product
Software Development Kits
SDKs
DTAPI - world renowned for its ease of use - enables you to integrate DekTec hardware in your application. Other SDKs are available for adding sophisticated digital-video functions toyour application without having to reinvent the wheel.Please note that some SDKs can also be used without DekTec hardware.
-
product
3U And 6U CPCI CARRIER Board
MS 1715
*Bus Interface:- 32 Bit/64 bit PCI Bus with cPCI Interface*Two slots of 32/64 bit PMC connector interface*Speed of operation up to 66MHz*64 bit, 66MHz PCI Bridge based design*Self Test future
-
product
Development Platforms and Accessories
Development chassis for VPX and SOSA aligned module payloads. The DK3 / DK6 for 3U and 6U VPX system design, support air and conduction cooled modules with quick conversion that tracks and streamlines your development cycle.
-
product
Isolated Programmable Multifunction Counter Board
APCI-1710
Wide application possibilities through free combination4 modules with numerous functions quickly and easily programmableEach of the 4 modules is programmed with a function. The 4 modules can either be programmed with the same function or freely be combined with 4 different functions.
-
product
10 Gb/s SFP/SFP+ Evaluation Board
EV-SFP-171
The purpose of this SFP+ evaluation board is to provide the designer with a convenient means for evaluating SFP+ fiber optic transceiver such as 10 Gb/s(up to 16 Gb/s) SFP/SFP+ transceiver compliant with ANSI Fibre Channel FC‐PI‐5 for high speed electrical and optical specifications. This board provides SMA connectors for high speed TX and RX signals. The low speed control signals such as Tx_Fault, Rx_LOS and Rate_Selects can be controlled by using on board switches and test points. A connector for 2 wire serial interface to the module is also provided.
-
product
COM Express Boards
COM Express is a highly integrated Computer On Module. It can be considered as a component (integrated circuit) in more complex designs.
-
product
COM Express Type 6 Development Baseboard
CEB94011
*COM Express type 6 baseboard for evaluation purpose*USB 3.0 supported*Port 80 display for debugging*Smart battery supported
-
-
product
Dynamic Test Board Vehicle Simulator
DTB
The Dynamic Test Board vehicle simulator range enhances functional testing by allowing greater test depth before the prototyping stage.
-
product
Board Fault Locator
SYSTEM 8 (BFL)
The SYSTEM 8 Board Fault Locator provides the user with the ability to functionally test all common digital ICs in and out-of-circuit. A combination of industry recognised test techniques provides a high level of fault coverage. Additional tools are provided by the SYSTEM 8 Premier software to further enhance the unit\'s wide range of applications.
-
product
Connector Board for Cable and Harness Tester
CB49
Populated with solder pads to accept a suite of TE-Connectivity Micro-MaTch connectors, this board addresses markets plagued by vibration and fretting corrosion, and requiring "miniaturized connectivity". Rated to 500Vdc/350Vac, the CB49 may be used on all CableEye models. The CB49, sold without connectors, contains nine sets of 20 solder pads accommodating numerous configurations of Micro-MaTch connectors.
-
-
product
RTM Actuator Signal Conditioning Board
MS 3630I
CPCI Rear IO Actuator Signal Conditioning Board is a signal conditioning and interface board for CPCI based Advanced Compute & IO Module (MS3639i). This board primarily focusing on Primary and Secondary actuator interface. This card shall handle excitation signals, conditioning, feedback measurement, power measurement. Card has high resolution Digital POTS, Direct Digital Frequency synthesizers, DAC, Discrete Input and Outputs, Analog measurement circuits for handling all sensor. All interface are brought to two 96 Pin Euro Connector.
-
product
3U CPCI CPU Boards
Advantech 3U CPCI boards are Intel based CPU blades that support single or dual processors that fully utilize I/O features of Intel® chipsets.
-
product
TySOM Embedded Prototyping Boards
TySOM™ is a family of embedded system prototyping boards. Depending on the board, one of three FPGAs will be at its heart: a Xilinx Zynq® UltraScale+™, a Xilinx Xilinx Zynq-7000 or a Microchip PolarFire SoC. The boards are compatible, through industry standard interfaces (FMC or BPX), with Aldec’s wide range daughter cards, making Aldec’s TySOM embedded prototyping boards ideal for the rapid development of applications that include automotive (and ADAS, in particular), artificial intelligence (AI), machine learning (ML), embedded vision, embedded-HPC (including edge-processing), IoT, IIoT and industrial automation.
-
product
PXIe HSS Optical FPGA Board
PXIe-8324
The Conduant PXIe-8324 Optical FPGA board provides the user with a hardware platform that is able to sustain full-duplex high-bandwidth transfers through its 8-lane Gen3 PXI Express (PXIe) interface and its 24-lane optical interface.
-
product
Analog Interface Boards
Model 4861B OEM
* 114578-24 board has 4 isolated analog outputs, 4 isolated analog inputs, 4 isolated drivers and 8 digital inputs* GPIB interface header includes GPIB address switch input signals.* Serial interface header includes RS-232 and RS-485 signals. Use the 114597 Serial Cable Kit to connect the serial signals to your rear panel* Use with any ICS GPIB Connector/Address Switch Assembly.* Runs on 12 Vdc regulated power.
-
product
6U CompactPCI Multifunction I/O Board
CPCI-MFIO-6U
The CPCI-MFIO-6U is a 6U CompactPCI multifunction I/O board. The CPCI-MFIO-6U offers 32 channels of 16 bit A/D, four 16 bit D/A, 16 digital I/O, counter / timers, and one PMC expansion slot for additional I/O. There is a local 60 Mhz TMS320C31DSP processor to supervise all the I/O activity. The DSP can be programmed by the end user to execute application specific code. The CPCI-MFIO-6U is ideally suited for factory automation, automatic test equipment, test & measurement, and control systems.
-
product
High Performance Embedded Development Kit
TySOM EDK
The TySOM™ Embedded Development Kit is for the embedded designers who need a high-performance RTL simulator/debugger for their embedded applications such as IoT, Automotive, Factory automation, UAV and Robotics. The kit includes Riviera-PRO™ Advanced Verification Platform and a TySOM development/prototyping board. TySOM boards come with either a Zynq 7000 chip (FPGA + Dual ARM® Cortex™-A9) or with a Zynq® UltraScale+™ MPSoC device. These boards include memories, and various communication and multimedia interfaces in addition to FMC connectors for peripheral expansion. Reference designs for application such as IoT, ADAS, 4K UltraHD imaging and Robotics and a complete reference design, which contains the SW (Linux) and all the hardware blocks required to support the peripherals on the board, are provided.
-
product
Burn-In Board Tester
Focus-275
Focus275 is a tester for burn-in board.It can improve reliability of burn-in board by inspecting boards for burn-in test by Focus275 regularlyBoth short open test and component test can be done by sending electric signals for special socket contactor and edge part.
-
product
Ada Development Environment
GNAT Pro
GNAT Pro is a robust and flexible Ada development environment. It comprises a full Ada compiler (Ada 83, Ada 95, and Ada 2005 features) based on the GNU GCC technology, an Integrated Development Environment (GNAT Programming Studio), a comprehensive toolsuite including a visual debugger, and a set of libraries and bindings.
-
product
Single Board Computer
VPX6-1958
Curtiss-Wright Defense Solutions
The VPX6-1958 rugged, high performance 6U OpenVPX Single Board Computer (SBC) combines Intel's powerful Core i7 processor with the power and flexibility of the VPX platform's high speed fabric interconnects. The VPX6-1958 supports Intel's 4th Generation Core i7-4700EQ processor.
-
product
Interfaces And Control Boards
Acts as a bridge between a machine, motor controller, or PLC and related drive amplifier, feedback device and/or software.
