Analog Digital
-
Product
Digitizers for VXI & PXI
-
Update your legacy systems with new digitizers from Astronics. Packed with features, these digitizer test instruments provide exceptional accuracy and performance.
-
-
Product
Digital Multimeter, 6 Digit
34465A
-
Resolutions up to 6 digitsReading rates up to 50,000 readings/sMemory up to 2 million readingsCurrent ranges from 1 A to 10 AUSB and LAN interfaces, optional GPIBBenchVue software enabled: Do more with your PC and instrument together, no programming required. Easily control your DMM, quickly build automated tests, log measurements and save precious time.
-
Product
NI-9775 , ±10 V, Up to 20 MS/s/ch, 14-Bit, 4-Channel C Series Digitizer Module
784539-01
-
The NI-9775 provides referenced single-ended analog inputs with two timing modes for applications such as fault detection in electrical transmission lines or structural failure events. You can use the NI-9775 to measure finite samples up to 20 MS/s/ch to capture fault detections or to measure continuously at up to 4 MS/s. You also can use the built-in analog reference trigger to assist with high speed phenomena. Additionally, the NI-9775 supports waveform streaming at a lower sample rate.
-
Product
NI-9401, 5 V/TTL, 8 Bidirectional Channels, 100 ns C Series Digital Module
779351-01
-
5 V/TTL, 8 Bidirectional Channels, 100 ns C Series Digital Module - The NI‑9401 is a configurable digital I/O interface for input or output in 4‑bit increments. Therefore, the NI‑9401 can create three configurations: 8 digital inputs, 8 digital outputs, or four digital inputs and four digital outputs. With reconfigurable I/O (RIO) technology (CompactRIO only), you can use the LabVIEW FPGA Module to program the NI‑9401 for implementing custom, high-speed counter/timers; digital communication protocols; pulse generation; and more. Each channel features transient isolation between the I/O channels and the backplane.
-
Product
Ethernet/LXI digitizerNETBOX 14 Bit High Speed Digitizer - 500 MS/s on 4 Channels, 4 Single-Ended Inputs
DN2.445-04
-
The digitizerNETBOX DN2.44x series allows recording of one, two, four or eight synchronous channels with sampling rates of 130 MS/s up to 500 MS/s. These products offer outstanding A/D features in resolution, bandwidth and speed as a remote instrument. The powerful A/D amplifier section offers six different input ranges, two input paths, AC/DC coupling and noise reduction filters.
-
Product
8/16-CH 16-Bit Analog Output Cards
PCI-6208/6216 Series
-
ADLINK PCI-6208/6216 series are 8 or 16-CH, 16-bit, analog output cards. The PCI-6208V-GL offers 8 voltage outputs with ±10 V range, featuring 15-bit monotonicity and 10 V/μs slew rate. The on-board analog switches minimize the power-on glitches. PCI-6216V expands the voltage output channels to a total of 16 for higher analog output density requirements. In addition to the voltage output functions, the PCI-6208A features 8 current outputs with ranges of 0-20 mA, 4-20 mA, and 5-25 mA. The daughter board EXP-8A provides high-quality voltage to current transducers. The PCI-6208A device is capable of delivering 14-bit monotonicity with 1.3 mA/μs slew rate. ADLINK PCI-6208 series devices provide high-resolution, high-density analog output functionalities and are suitable for ATE, signal generation, industrial process control, servo control and other industrial control applications.
-
Product
16-Ch Sink-Type Digital Output EtherCAT Slice IO Module
AMAX-5057
-
Channels:16 (Sink Type)Voltage Rating:10~30VDCRated Current Output:0.3A per channel atsignal "1"Leakage Current:25 μA per channel atsignal "0"Output Delay:From logic level 0 to 1:10μs;From logic level 1 to 0: 100μs
-
Product
Ethernet/LXI digitizerNETBOX 8 Bit High Speed Digitizer - 5 GS/s on 6 Channels, 2.5 GS/s on 12 Channels, 1.25 GS/s on 24 Channels
DN6.225-24
-
The digitizerNETBOX DN6.22x series allows recording of up to 24 channels with sampling rates of up to 5 GS/s and a bandwidth of 1.5 GHz. These Ethernet Remote instruments offer outstanding A/D features both in bandwidth and signal quality. The combination of high sampling rate and resolution makes these digitizers the top-of-the-range for applications that require high speed signal acquisition. The digitizerNETBOX can be installed anywhere in the company LAN and can be remotley controlled from a host PC.
-
Product
PXIe-4304, 24-Bit, 32-Channel, 5 kS/s, 42 V, PXI Analog Input Module
783867-01
-
24-Bit, 32-Channel, 5 kS/s, 42 V, PXI Analog Input Module—The PXIe‑4304 is a filtered analog input module for higher voltage measurements. The module offers the ability to select a digital filter per channel to provide extra filtering performance. You also can operate up to four different sample rates and triggering configurations concurrently to ensure you measure every sensor as needed. The module has an A/D converter per channel to enable a simultaneous sample rate at the maximum sample rate across the input range. The included NI‑DAQmx driver simplifies hardware configuration and measurement.
-
Product
PCIe Octopus Express 14-Bit Digitizer
-
The GaGe Octopus Express 83XX CompuScope PCIe digitizer board features 14-bit resolution with sampling rates up to 125 MS/s with true Effective Number of Bits (ENOB) of 11-bits with 10 MHz input.
-
Product
NI-9401, 5 V/TTL, 8 Bidirectional Channels, 100 ns C Series Digital Module
782401-01
-
5 V/TTL, 8 Bidirectional Channels, 100 ns C Series Digital Module - The NI‑9401 is a configurable digital I/O interface for input or output in 4‑bit increments. Therefore, the NI‑9401 can create three configurations: 8 digital inputs, 8 digital outputs, or four digital inputs and four digital outputs. With reconfigurable I/O (RIO) technology (CompactRIO only), you can use the LabVIEW FPGA Module to program the NI‑9401 for implementing custom, high-speed counter/timers; digital communication protocols; pulse generation; and more. Each channel features transient isolation between the I/O channels and the backplane.
-
Product
Handheld Digital Multimeter, 4 Digit
U1242B
-
10K counts digital multimeter with switch/relay counter, harmonic ratio and dual/differential temperature functions for installation and maintenance troubleshooting.
-
Product
PCIe-7821, Kintex 7 FPGA, Digital Reconfigurable I/O Device
785359-01
-
The PCIe‑7821 is a reconfigurable I/O (RIO) device that features a user-programmable FPGA for onboard processing and flexible I/O operation. With LabVIEW FPGA, you can individually configure the digital lines as inputs, outputs, counter/timers, PWM, encoder inputs, or specialized communication protocols. You can also program custom onboard decision making that executes with hardware-timed speed and reliability. Each line offers software-selectable logic levels. The PCIe‑7821 is well-suited for a wide variety of applications, such as high-speed waveform generation, sensor simulation, hardware‑in-‑the‑loop (HIL) test, bit error rate test, and other applications that require precise timing and control.
-
Product
NI-9423, 24 V, 8 Channel (Sinking Input), 1 µs C Series Digital Module
779009-01
-
24 V, 8 Channel (Sinking Input), 1 µs C Series Digital Module - The NI‑9423 works with industrial logic levels and signals to connect directly to a wide array of industrial switches, transducers, and devices. Each channel is compatible with 24 V logic levels, can accept up to 30 V discrete logic levels, and has an LED that indicates the status. The NI‑9423 offers isolation between the input and output banks from channel to earth ground. The NI‑9423 is a correlated digital module, so it can perform correlated measurements, triggering, and sychronization when installed in a CompactDAQ chassis.
-
Product
Dynamic D/A Converter, 16-channels, 16-Bit, Unipolar, 30 V/20 mA
M9188A
-
The M9188A is a PXI based, 1-slot unipolar Dynamic DAC which has 16 channels capable of supplying typical waveforms at high voltages. It has 4 isolated banks with 4 channels in each bank.
-
Product
PXI/PXIe 16-Channel Digital Output Module
42-412A-024
-
The 40-412A-024 (PXI) and 42-412A-024 (PXIe) are 16-Channel Digital Output modules with high output voltage and current capability. The outputs can be used for high or low drive and each channel is capable of sourcing 0.5A from the high side or 0.5A sink on the low side. Accidental operation of both high and low side driver on the same channel is prevented by the supplied driver. Outputs are fully protected against over-voltage, over-current and thermal overload, ensuring robust and reliable operation in the toughest test environments. For high side driving, the voltage source is supplied externally, allowing the module to drive high capacity loads separate from the chassis power supply. For low side driving, the external source is not used and the module’s output operates an open collector or open drain driver.
-
Product
64 Input USB Modular Digital I/O
U2652A
-
The Keysight U2652A USB Digital I/O is a cost-effective device with its offering of 64 opto-isolated digital lines. It comes bundled with the Keysight Measurement Manager (AMM) software for quick set up and data logging. Simplifying this further is the command logger function offered in the Keysight Measurement Manager that allows capturing of configuration commands that can be easily converted to snippets of VEE code. Other supported languages are VB, C++, and C#.
-
-
Product
PXIe 8 Bit High Speed Digitizer - 2.5 GS/s on 1 Channel, 1.25 GS/s on 2 Channels, 1.5 GHz Bandwidth
M4X.2223-X4
-
The 9 models of the M4x.22xx-x4 Express series are designed for the high speed data acquisition. Each of the input channels has its own A/D converter and its own programmable input amplifier. This allows the recording of signals simultaneously on all channels without any phase delay between them. The extremely large on-board memory allows long time recording even with the highest sampling rates.
-
Product
PXI/PXIe Analog Output/Current Loop Simulator Module - 4 Channel
43-765-004
-
The 41/43-765-004 is an 4-channel Analog Output Module designed to meet the requirements of industrial control applications utilising current loops 4 – 20mA. It consists of up to four 16-bit, digital-to-analogue converters (DAC), capable of creating four current outputs each. Output current within 0mA - 4mA and 20mA - 24mA, give the ability to simulate error or extra signalling conditions. The ±24mA mode gives the ability to simulate either sourcing or sinking sensor.
-
Product
Digital Input Board
VME-1128
-
VME-1128 is a 128-bit High-Voltage Digital Input Board with Built-in-Test. This product complies with the VMEbus specification (ANSI/IEEE STD 1014-1987, IEC 821 and 297) with the following mnemonics: A24:A16:D32/D16/D08 (EO): Slave: 39/3D:29/2D Form factor: 6U
-
Product
Handheld Digital Multimeter, 4.5-digit, with Organic LED Display (OLED)
U1253B
-
The Keysight U1253B 4.5-digit handheld digital multimeter (DMM) is feature-packed to simplify the troubleshooting of electronics and electrical circuits indoors, on the bench or in the field. Key capabilities include its organic LED (OLED) display that provides razor-sharp readings even in dark, off-angle situations. The U1253B is the world's first OLED handheld DMM of its kind. For those long, continuous measurements, the DMM equips you with the easy-to-use GUI data-logging software to automate virtually unlimited data recordings to PC. The U1253B comes with an integrated 20 MHz frequency counter for high frequency measurements, and a built-in programmable square-wave generator with selectable frequency and duty cycle. With the versatile U1253B, you are well equipped to perform thorough troubleshooting of any faulty circuit.A multi-award winner
-
Product
PXIe 64-Channel Digital Output Module
42-412A-021
-
The 40-412A-021 (PXI) and 42-412A-021 (PXIe) are 64-Channel Digital Output modules with high output voltage and current capability. The outputs can be used for high or low drive and each channel is capable of sourcing 0.5A from the high side or 0.5A sink on the low side. Accidental operation of both high and low side driver on the same channel is prevented by the supplied driver. Outputs are fully protected against over-voltage, over-current and thermal overload, ensuring robust and reliable operation in the toughest test environments. For high side driving, the voltage source is supplied externally, allowing the module to drive high capacity loads separate from the chassis power supply. For low side driving, the external source is not used and the module’s output operates an open collector or open drain driver.
-
Product
Digital I/O Vector Development Software
DIOEasy
-
DIOEasy offers test engineers an efficient tool for developing, debugging, and executing digital test vectors for Marvin Test Solutions' GX5050 series, GX5150 series, GX5280 series and GX5291, GX5292, GX5293 and GX5295 dynamic digital instruments.Digital I/O (DIO) systems are very complex and typically require a substantial amount of programming effort to define data vectors. In order to simplify vector development, Marvin Test Solutions developed Windows-based DIOEasy, providing users with an easy to use interface. Toolbars and menus provide quick access to vector editing and viewing tools.
-
Product
Digitizer Adapter Module For FlexRIO
-
Digitizer Adapter Modules for FlexRIO can be used with a PXI FPGA Module for FlexRIO or the Controller for FlexRIO to create a high‐performance instrument with customizable firmware. With sampling rates from 40 MS/s to 3 GS/s and up to 32 channels, these modules cover a wide range of requirements for both time- and frequency‐domain applications. Digitizer adapter modules also provide digital I/O capability for interfacing with external hardware.
-
Product
PCIe-5763, 16-Bit, 500 MS/s, 4-Channel PCI FlexRIO Digitizer Device
786168-01
-
The PCIe-5763 is a PCI FlexRIO Digitizer Device that simultaneously samples four channels at 500 MS/s with 16 bits of resolution and features 225 MHz of analog input bandwidth. With over 73 dB of SNR, the PCIe-5763 is ideal for applications that require a wide dynamic range with a wideband digitizer. The FlexRIO driver includes support for finite and continuous streaming modes, and you can implement custom algorithms and real-time signal processing on the LabVIEW-programmable Xilinx Kintex UltraScale FPGA. Available in AC and DC coupled variants, the PCIe-5763 is ideal for both time and frequency domain applications, including radar prototyping, LIDAR, communications, microscopy, OCT, event detection, and particle physics.
-
Product
PCIe Oscar Express 16-Bit Digitizer
-
The GaGe Oscar Express 44XX CompuScope PCIe digitizer board features 16-bit resolution with sampling rates up to 100 MS/s with true Effective Number of Bits (ENOB) of 12.2-bits with 10 MHz input.
-
Product
32-CH Isolated DI & 32-CH Isolated DO PCIe Card with High Input Range
PCIe-7432
-
ADLINK PCIe-7432 is a 32CH Isolated DI & 32CH Isolated DO PCIe Card, featuring robust 2,500V isolation protection, suitable for most industrial applications. Input range up to 24V makes it easy to acquire status of external devices (PCIe-7432HIR output range is from 5 to 35V), making it suitable for relay driving and industrial automation applications. Also provided are two easily configurable interrupt sources on digital input channels.
-
Product
NI-9477, 60 V, 32-Channel (Sinking Output), 8 µs C Series Digital Module
779517-01
-
60 V, 32-Channel (Sinking Output), 8 µs C Series Digital Module - The NI‑9477 works with industrial logic levels and signals to connect directly to a wide array of industrial relays, solenoids, and motors. Each channel is compatible with signals from 5 V to 60 V and … features isolation from channel‑to‑earth ground. You can wire the NI‑9477 channels in parallel to sink up to 20 A of current per module (1 A per channel maximum).
