Analog Input Output
Analog I/O are Devices that have the capability of sending and receiving analog signals.
-
Product
Analog And Digital Sensor Measurement Data For CAN Applications.
K- AN8
-
The stackable K-AN8 is our cost effective solution to measuring analog and digital/PWM sensors together in one module. Extremely easy to use and stackable with all of our other K-series instrumentation modules. The K-AN8 includes our unique power down and WakeOnCAN feature for quick installation on long term unattended fleet test vehicles.
-
Product
NI-9477, 60 V, 32-Channel (Sinking Output), 8 µs C Series Digital Module
780174-01
Digital Module
60 V, 32-Channel (Sinking Output), 8 µs C Series Digital Module - The NI‑9477 works with industrial logic levels and signals to connect directly to a wide array of industrial relays, solenoids, and motors. Each channel is compatible with signals from 5 V to 60 V and … features isolation from channel‑to‑earth ground. You can wire the NI‑9477 channels in parallel to sink up to 20 A of current per module (1 A per channel maximum).
-
Product
Oscilloscope, 200 MHz, 2 Input Channels, 2 GS/s interleaved, 14 Mpts/Ch
T3DSO1202A
Oscilloscope
200 MHz, 1 GS/s per Ch, 2 GS/s interleaved, 2 CH, 14 Mpts/Ch DSO with 7" Color Display.
-
Product
Oscilloscope 1 GHz, 2 Analog Channels
DSOX3102G
Oscilloscope
The DSOX3102G 1 GHz oscilloscope provides 2 analog channels, 4 Mpts memory, 1,000,000 waveforms/sec update rate, zone touch trigger with an 8.5-in capacitive touch screen, and standard embedded software with waveform and measurement histograms.
-
Product
Analog Ultrasonic Detection System
ULTRAPROBE 2000
-
Designed for ease of use, it often takes no more than 15 minutes to become competent in testing with the ULTRAPROBE 2000 Kit Complete. Fast accurate diagnosis through the ULTRAPROBE 2000 System will dramatically reduce unplanned down time and shorten planned outage time.
-
Product
Thermalert Clinical Montoring Thermometer With Analog Output
TH-5/AOP
-
The TH-5?AOP is one of our most economical precision thermometers in the Physitemp product line. The TH-5/AOP offers the same high accuracy (0.1°C ±1 digit) and resolution as all our other thermometers, but with a narrow temperature range. The TH-5 is ideally suited for either a laboratory or hospital setting where continuous temperature readings within the physiological range are sufficient.
-
Product
PXIe-4353, 32-Channel, 24-Bit PXI Temperature Input Module
781348-01
Analog Input Module
32-Channel, 24-Bit PXI Temperature Input Module—The PXIe‑4353 is a thermocouple input module that provides integrated data acquisition and signal conditioning for temperature measurements. The PXIe‑4353 includes increased accuracy and synchronization features for scalable measurement systems from low‑ to high‑channel counts. The high accuracy is attributed to the NI TB‑4353 isothermal terminal block that optimizes thermal conductivity between the thermocouple terminals and the cold-junction compensation (CJC) channels. The PXIe‑4353 has two auto zero channels for offset compensation as well as open thermocouple detection to identify disconnected thermocouples.
-
Product
Mixed Signal Oscilloscope - 200 MHz, 4 Analog Plus 16 Digital Channels
MSOX3024T
Oscilloscope
200 MHz4 analog plus 16 digital channels Easily view and analyze your signals with on the large 8.5-inch capacitive touch screen Isolate signals in seconds with exclusive Zone touch triggering See more signal detail with the 1,000,000 wfms/s update rate Capture more data with up to 4 Mpts memory Expand your measurement capabilities with full upgradability: Add bandwidth, 20 MHz arbitrary waveform generator, 3-digit voltmeter, serial trigger and analysis & mask testing at any time
-
Product
NI-9425 , 24 V, 32-Channel (Sinking Input), 7 µs C Series Digital Module
780176-01
Digital Module
24 V, 32-Channel (Sinking Input), 7 µs C Series Digital Module - The NI‑9425 works with industrial logic levels and signals to connect directly to a wide array of industrial switches, transducers, and devices. Each digital input line is compatible with 24 V logic levels. The NI‑9425 offers isolation between the input and output banks from channel to earth ground. You cannot use the NI‑9425 in a CompactDAQ chassis to perform counter operations.
-
Product
MXG X-Series RF Analog Signal Generator, 9 kHz to 6 GHz
N5181B
Signal Generator
Take your devices & designs to their limit with outstanding hardware performance, including unmatched phase noise & spurious characteristicsDrive power amplifiers & characterize nonlinear behavior with industry-leading output powerThoroughly test receiver performance by simulating complex analog modulation scenarios with multi-function generator capabilityLower your cost of ownership with 3-year cal cycles & comprehensive solutions for self-maintenance
-
Product
NI-9375, 30 V, 32-Channel (Sinking Input, Sourcing Output), 7 µs (Input)/500 µs (Output) C Series Digital Module
781030-02
Digital Module
30 V, 32-Channel (Sinking Input, Sourcing Output), 7 µs (Input)/500 µs (Output) C Series Digital Module - The NI‑9375 is a digital I/O interface that works with industrial logic levels and signals for direct connection to a wide array of industrial switches, transducers, and other devices. Each digital input line is compatible with 24 V logic levels, and all the output lines are compatible with 6 V to 30 V signals, based on the external power supply. The NI‑9375 offers isolation between the input and output banks from channel‑to‑earth ground.
-
Product
Light-to-Analog Sensors (Voltage)
-
Renesas' light-to-voltage silicon optical sensors combine a photodiode array, a non-linear current amplifier and a micropower op amp on a single monolithic IC. Applications for these devices include display backlight control, keypad dimming, anti-glare mirror systems, and industrial and medical light sensing applications.
-
Product
FTTP Multi-Port Output 1550nm External Modulation 47~862MHz
HT8500M
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai HT8500M series, Multi-optical port output externally modulated transmitter, a research product which is designed for FTTx PON large area and multi-user access. HT8500M series, use high-power , low noise, narrow linewidth, continuous broadcast, DFB lasers. It can provide 4~10 way high linearity standard optical power output. It can connect 4~10 units high-power FTTB EDFA( Like Huatai HA5837-32). AS this product without EDFA, so each optical port can out put up to :CNR≥53.5dB, CTB≥-65dB, CTB≤-65dB, the high technical index.
-
Product
4-Ch, 16-Bit, 200 KS/s Isolated Analog Output USB 3.0 I/O Module
USB-5820
-
USB 3.0 SuperSpeedDaisy chainable by built-in USB hub4 x 16-bit analog output channels with 2,500 V DC isolationMultiple voltage and current output rangesRemovable European-type connectorSupported operating systems: Windows 10/11
-
Product
PXI 4 Slot BRIC 138x8 1-Pole Dual Analog Bus (3 sub-cards)
40-560A-021-138X8-M
Matrix Switch Module
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high-performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
SparkFun 16 Output I/O Expander Breakout
SX1509
-
Are you low on I/O? No problem! The SX1509 Breakout is a 16-channel GPIO expander with an I2C interface – that means with just two wires, your microcontroller can interface with 16 fully configurable digital input/output pins. But the SX1509 can do so much more than just simple digital pin control. It can produce PWM signals, so you can dim LEDs. It can be set to blink or even breathe pins at varying rates. This breakout is similar to a multiplexer or "mux," in that it allows you to get more IO from less pins. And, with a built-in keypad engine, it can interface with up to 64 buttons set up in an 8x8 matrix.
-
Product
Oscilloscope - 1 GHz, 4 Analog Channels
DSOX4104A
Oscilloscope
1 GHz4 analog channels Easily view signals on the large 12.1-inch capacitive touch screen Isolate signals in seconds with exclusive Zone touch triggering Capture more data with 4 Mpts memory and standard segmented memory See more signal detail with 1,000,000 wfms/s update rate Expand your measurement capabilities with full upgradability: Add bandwidth, digital channels, dual-ch 20 MHz arbitrary Wave Gen, 3-digit DVM, serial trigger and analysis & mask testing
-
Product
MSR160 Data Logger with Analogue Inputs
MSR160
-
Four integrated analogue inputs, a high measurement rate of up to 1000/s per channel and its gigantic memory capacity, all packed into a small format are the key characteristics of the MSR160 data logger. The analogue inputs of the robust mini logger can be used for conventional sensors with analogue outputs (e.g. CO2, conductivity, pH etc). In addition, a multiple output switching power supply is also provided.
-
Product
Oscilloscope: 100 MHz, 4 Analog Channels
DSOX2014A
Oscilloscope
100 MHz4 analog channels Easily view your signals on the 8.5-inch WVGA display Capture more data with up to 1 Mpts memory See more signal detail with 50,000 wfms/s update rate Expand your measurement capabilities with full upgradability: Add digital channels, 20 MHz function generator, 3-digit voltmeter, serial trigger and analysis, segmented memory & mask testing at any time Easily set up teaching labs with our free Educator's Resource Kit
-
Product
2 inputs Centesimal Thermometer Pt100
HD2127.1
-
Centesimal thermometer in the range ±199.99 °C, decimal outside this range, 2 inputs for Pt100 probes with SICRAM module. Measuring range -200 °C…+650 °C.
-
Product
NI-9472, 24 V, 8-Channel (Sourcing Output), 100 µs C Series Digital Module
779004-02
Digital Module
24 V, 8-Channel (Sourcing Output), 100 µs C Series Digital Module - The NI‑9472 works with industrial logic levels and signals to connect directly to a wide array of industrial switches, transducers, and devices. Each channel is compatible with signals from 6 V to 30 V, features transient overvoltage protection between the output channels and the backplane, and has an LED that indicates the status.
-
Product
Easy Connection Of IEPE Sensors To Voltage Input Measurement Devices
K- IEPE
-
Our K-IEPE module is designed to connect IEPE sensors to a voltage measurement device that normally cannot support IEPE sensors. The powered K-IEPE module simply enables IEPE sensors to be connected via the BNC terminals and will output the signal voltages to an analog measurement device.
-
Product
Analog Oscilloscope
PS-1005
-
* 100MHz ALT TRIGGER. * 20MHz LIMIT. * 1mV/DIV SENSITIVITY. * 2nS/DIV RESOLUTION. * DELAY SWEEP * CE, TUV GS, UL, CUL, IEC1010
-
Product
PXIe-1486, 8 Input, 8 Output, or 4 Input/4 Output PXI FlexRIO FPD-Link™ Interface Module
787455-01
Interface
The PXIe-1486 combines the Texas Instruments Flat Panel Display Link™ (FPD-Link™) interface with the Xilinx FPGA for high-throughput vision and imaging applications. This module provides a high-speed digital interface for using and testing modern advanced driver assistance systems (ADAS) and autonomous drive (AD) camera sensors and electronic control units (ECUs). Additionally, the PXIe-1486 makes use of a combination of FPD-Link™ serializers and deserializers with a Xilinx FPGA to provide a high-throughput and customizable FPD-Link™ interface on PXI. The included FlexRIO driver, with LabVIEW FPGA examples, provides access and control for power-over-coax, I²C back-channel communication, and general-purpose input/output (GPIO) communication on the FPD-Link™ channels. The PXIe-1486 is ideal for applications such as in-vehicle data logging, lab-based playback, or hardware-in-the-loop (HIL). FPD-Link is a trademark of Texas Instruments.
-
Product
C Series Digital Module
Digital Input Module
The C Series Digital Module interacts with a range of industrial switches, transducers, and devices. Some modules include an LED per channel that indicates the state of the channel. It supports input, output, or a combination of digital lines, and they can interact with a variety of voltages and logic levels, so they are well-suited for a variety of benchtop and industrial environments. Additionally, the C Series Digital Module also offers isolation options and sinking or sourcing capabilities to add further protection to your digital I/O application. When you use the C Series Digital Module with CompactRIO, you can use LabVIEW FPGA to create custom high-speed counter/timers, digital communication protocols, pulse generation, and more.The C Series Digital Module includes the NI-DAQmx driver and configuration utility that simplify configuration and measurements. NI-DAQmx supports NI programming environments as well as Python, ANSI C, C#.NET, and MathWorks MATLAB® software.
-
Product
Infiniium S-Series High-Definition Oscilloscope: 4 GHz, 4 Analog Plus 16 Digital Channels
MSOS404A
Oscilloscope
4 GHz bandwidth (upgradable)4 analog plus 16 digital channels Capture a longer signal trace with 20 GSa/s max sample rate and 100 Mpts/channel of standard memory Get superior signal integrity with system ENOB of 7.2 bits and 10-bit analog-to-digital converter (ADC)Gain increased usability with the multi-touch supported 15" capacitive touch screen and solid state drive for fast boot and reliability Improve your testing with a wide range of protocol, compliance, and analysis software
-
Product
Infiniium UXR-Series Oscilloscope: 25 GHz, 4 Channels, 1mm Inputs
UXR0254AP
Oscilloscope
The UXR0254AP is the 25 GHz, 4 channel, 1mm input, Infiniium UXR-Series real-time oscilloscope.
-
Product
Mixed Signal Oscilloscope 200 MHz, 2 Analog Plus 16 Digital Channels
MSOX3022G
Oscilloscope
The MSOX3022G 200 MHz oscilloscope provides 2 analog plus 16 digital channels, 4 Mpts memory, 1,000,000 waveforms/sec update rate, zone touch trigger with an 8.5-in capacitive touch screen, and standard embedded software with waveform and measurement histograms.
-
Product
WaveSurfer Oscilloscope, 200 MHz Bandwidth, 4 Input Channels, 12.5 Mpts/ch, 5 GS/s
WaveSurfer 4024HD
Oscilloscope
200 MHz, 5 GS/s, 4 Ch, 12.5 Mpts/ch DSO with 12.1" Capacitive Touch Screen Display.
-
Product
Analog & Digital I/O Modules
-
USB analog and digital I/O modules are a complete family of data acquisition modules for use in process control systems. The analog input modules can measure process signals such as DC voltage, thermocouples, 4-20mA current loops, discrete contact closures.
