AC Electronic Loads
Simulate voltage, current and power ranges.
-
product
1μΩ-4kΩ AC Milliohmmeter Low Resistance Tester
TH2521
Shenzhen Chuangxin Instruments Co., Ltd.
TH2521 AC Milliohmmeter is a high-performance and intelligent tester widely used to test contact resistance, internal resistance and battery voltage. The application of constant current source with 1kHz frequency can greatly eliminate the potential error caused by thermoelectricity on DUT. This meter has the function to automatically detect contact failures on test cable. At the range of 30mΩ, basic R resolution can reach 1μΩ. It is applicable for transformer, inductance coil copper resistance, relay contact resistance, switch, connector contact resistance, wire resistance, PCB line and via reistance dan metal defect detection, etc. In the mean time, signals, such as HIGH, LOW, PASS, can be output through HANDLER interface, thus it is very convenient to be used in automatic production line.
-
product
AC Resonant Test System for Cable
HTXZ / 130
Wuhan Huatian Electric Power Automation Co., Ltd.
Portable frequency conversion resonance voltage test device for domestic cables.
-
product
Electronic Inspection Systems
Intego's knowhow even makes it possible to identify challenging defects that may be located under the surface. One system is the inspection of chips by means of lock-in thermography, which visually represents the IR radiation intensity signal of electronics. Special lasers and flash lamps generate a very short heat impulse (10 ms) on the chip, which generates a measurable heat flow. In most cases, a resolution of < 1 μm can be achieved.
-
product
Load Boards
The Hartmann Load Boards were originally designed for in house use to test, setup and qualify standard chassis and custom systems. As demand for these products presented itself, Hartmann answered the call with a lineup of high quality load boards.
-
product
1KVA 3KVA 5KVA Digital AC Power Source
RK5001
Shenzhen Chuangxin Instruments Co., Ltd.
The AC Power Source is widely used in home appliance manufacturing, electrical and electronic manufacturing industry, IT industry and computer equipment etc. manufacturing industries and Laboratories and electronic products testing organization.
-
-
product
Electronics Failure Analysis System
Sentris
Due to the continued decrease in integrated circuit feature size and supply voltages, detecting and locating the miniscule amount of heat generated by failure sites has become increasingly difficult. Sentris pinpoints low-level infrared thermal emissions from IC faults such as short circuits and leakage current.
-
product
Through Hole type AC Current Sensor
CT-6K
MULTI MEASURING INSTRUMENTS Co., Ltd.
For measuring current generally (through hole type)
-
-
product
Load Cell Transmitter
MODEL SST-LV
The SST-LV is a Plug & Play Smart TEDS IEEE 1451.4 compliant Transmitter. Just plug in a TEDS compatible Load Cell or Torque Sensor and the SST-LV will automatically self-calibrate. When used with a non-TEDS Load Cell or Torque Sensor, the SST-LV Transmitter is easily programmed using a PC with an RS232 port and Instrument Setup (IS) software, which provides a graphical user interface. The SST-LV may be powered from 12-30 Vac or 10-48 Vdc. The SST-HV Has an Isolated transducer excitation output that is selectable between 5Vdc or 10Vdc. There are Dual solid state relays and an Isolated 4-20 mA, 0-20 mA or 0-10V analog output. There are three Isolated serial data transmitter output ( RS232 , Half-duplex RS485, full-duplex RS485 ) and three serial protocols that are software selectable (Modbus RTU, Modbus ASCII and Custom ASCII). Isolation to 250V rms is provided for power, signal input, analog output, relay outputs, and communications. Isolation adds safety and avoids possible ground loops. The transducer excitation output is isolated to 50V from signal ground.
-
product
Clamp type AC Current Sensor／for Low Leakage Current Measurements(ZCT Series)
ZCT-80H
MULTI MEASURING INSTRUMENTS Co., Ltd.
*High precision clamp type ZCT sensor*Big CT window,φ80mm*AC 0～10A*Least affection from the external magnetic field and residual current
-
product
ESI(Electronics Systems Integration Unit)
MS 2004
The ESI subsystem provides platform interfaces like Gyro and on board Radar Blanking. This unit receives Analog and Digital GYRO inputs from ship and pre- trigger pulses from on board radars of the ship. This unit measures and provides the ship heading data to VARUNA ESM system. It also provides Heading, Roll and Pitch data to the ECM system. This unit also generates band wise composite ESM Rx. Blanking gates and provides all the required interfaces to ESM receiver, ECM System and System Controller units.
-
product
Through Hole/ Donut Load Cell (3.00 O.D.) Compression Only
THD SERIES
Our THD Series through hole donut load cells offer an outside diameter of 3.00 inches and up to nine different through hole diameter options per capacity range. These load cells are manufactured from heat treated 17-4 ph stainless steel. The sensing element incorporates bonded foil strain gages of the highest quality and are sealed for protection against most industrial Environments.
-
product
Electronic Outside Air Temperature
OAT
The outside air temperature sensor is an electrical component that complements the control of a modern heating system.
-
product
Clamp type AC Current Sensor／for Leakage Current Measurements(ZCT Series)
ZCT-150T
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Easy installation.*For leakage current measurements of bus bar*Unique split and track type ZCT sensor*High sensitive and least affection from external magnetic field
-
product
Unclamped Inductive Load Tester
ITC55100C
The system has been designed around a very powerful micro-controller that gives it a timing resolution of 40ns, twenty times faster than the previous model. Its response time to the peak and zero current is improved ten times. Combined this gives greater accuracy for the charging and avalanche times and for the reported peak drain current.
-
-
product
Precision Gram Load Cell Universal/ Tension or Compression
GSO SERIES
The GS0 Series Load Cells can be utilized in tension or compression or both with excellent compliance. The force sensing end of the anodized aluminum GS0 Series is tapped 6-32 thru for attachment possibilities for almost any application. Bonded foil strain gages at the sensing element provide for excellent stability over the suggested temperature range and ensure long term reliability. Call for application assistance.
-
product
Split Type AC Current Sensor
CTF-10
MULTI MEASURING INSTRUMENTS Co., Ltd.
*For AC current and power measurements.*Wide measuring range (AC 0.1～60A).*Compliant with RoHS drective.
-
product
AC Ground Bond Tester
446
Our 446 model is a 4-in-1 tester with AC Hipot, DC Hipot, Insulation Resistance, and Ground Bond capabilities. This tester features a simple design and easy-to-use interface, reducing setup time and increasing production-line throughput for your application. The 446 is equipped with multiple memories and an optional USB port for remote BUS communication so you can quickly perform tests on a variety of DUTs from the front panel or with a PC. Add to user safety by equipping your tester with Personal Protective Equipment (PPE) via the built-in safety interlock.
-
product
1000 Amp AC Digital Clamp Meter
DL6401
This clamp meter offers many features in addition to basic current testing. The slim design combined with the tear shaped jaw makes it an ideal unit for use in crowded panels and tight spaces.The data hold and peak capture function makes this a versatile and cost effective clamp meter.
-
product
Electronic Circuit Simulator
SimOne
SimOne lets you perform full-featured electronic circuit simulation using state-of-the-art and classic modeling algorithms while taking full advantage of modern computers.SimOne does all the basic circuit analyses common to SPICE modeling systems and as well provides important Stability analysis.
-
product
Automotive Electronics Functional Test System
TS-5020
The Keysight TS-5020 Automotive Functional Test System is a low cost, scalable test system designed with “just-enough-test” concept for medium complexity electronic control modules, such TPMS, RKE and body electronic modules
-
product
Small Engine AC Motoring Dynamometers
SAKOR Technologies developed its new Small Engine AC Motoring Dynamometer specifically to meet the needs of engine manufacturers who must now comply with engine testing procedures required by new emission standards contained in 40 CFR Part 1065. These new requirements apply to almost every kind of small internal engine, including those in handheld power tools and lawn and garden tools.
-
product
Signal, Module, Receiver, QuadraPaddle, 90 Series, 192 Position, Fully Loaded w/ Twin Female Contacts
510150130
Primary mating module 510151105. (May mate with other ITA modules, as well.)
-
product
Mini AC Leakage Current Clamp Tester
M-104+
MULTI MEASURING INSTRUMENTS Co., Ltd.
・33mmφCT window and ultra compact size.・Data-hold function. Especially useful when working in dark or hard to get areas.・Low cost type, Core shielding is not equipped.
-
product
AC+DC Power Sources/Amplifiers
The N4A range of AC+DC Power Sources are available with a variety of output power ratings from 6kVA up to and above 30kVA. They are the perfect solution for general power source applications as well as IEC61000 electromagnetic compatibility standards testing, offering low THD and excellent reliability.
-
product
Mixed-Signal Active Load Pull System
MT1000 And MT2000 Series
The MT1000 and MT2000 mixed-signal active load pull systems are the best commercially proven solutions capable of performing load pull at high speeds of up to 1000 impedance/power states per minute with no limitation on Smith Chart coverage, under the following conditions:Single-tone CW and pulsed-CW RF signalDC and pulsed-DC biasTime-domain NVNA voltage and current waveforms and load linesFrequencies between 1 MHz and 40 GH
-
product
Electronic Calibration Module (ECal), 40 GHz, 2.92 Mm, 2-port
N4692D
The Keysight N4692D microwave electronic calibration (ECal) module makes calibration of Keysight vector network analyzers fast, easy and accurate. The N4692D is a precision 2-port ECal module that supports 2.92 mm connectors up to 40 GHz. Select either female-female, male-male, or female-male connectors. The plastic storage case for the N4692D is included for securing your ECal module and accessories.
-
product
IntegraVision Power Analyzer, 4 Channels, 3-Phase AC
PA2203A
Achieve better power analyzer accuracyAddress multiple test scenarios with the flexibility of wide-ranging, isolated inputsVisualize transients, in-rush currents & state changes with a high-speed digitizerAnalyze voltage, current and power in the time and frequency domains12.1" touchscreen
