VxWorks
-
Product
Shared Memory Network PCI Express Interface
PCIe-SMN
-
Avionics Interface Technologies
2.125 Gbps Optical loop network - Single-mode and Multi-mode optical interfaces supported - Up to 256 Shared Memory Network nodes supported - Up to 200 MByte/sec sustained data rates - Maximum 500 nS latency between nodesNetwork interrupts supported - PCIe 2.0 (x4) CompliantSoftware Drivers available for Windows, Linux, LabVIEW Real-Time, and VxWorks
-
Product
HS1760/MIL-STD-1760E XMC Network Interface Controller
XMC-1760-NIC-FP
-
Avionics Interface Technologies
Configuration Variants available: XMC-HS1760-NCNT: One NC Node and One NT Node, XMC-HS1760-NCNC: Two NC Nodes, XMC-HS1760-NTNT: Two NT Nodes - SAE AS5653-Compliant Network Controller/Network Terminal NIC - Unsolicited data path for handling Fibre Channel link service or non‐FC-AE‐1553 traffic - Supports DMA for high speed streaming of data75 Ohm single‐ended or 150 Ohm Differential coax interface – TNC connectors - Each port supports 1.0625 Gbps speed - ANSI C API interface for both NC and NT - Device driver support: Windows, Linux, & VxWorks - Quad (4) port board available on request
-
Product
Extreme Rugged PC/104 Single Board Computer with Intel® Atom™ Processor System-on-Chip
CM1-BT1
-
The CMx-BTx is a PC/104-based, Single Board Computer (SBC), fully compliant with the PCI-104 Specification, Version 1.1 and partially compliant with the PC/104 Specification, Version 2.6. PC/104 SBCs are very compact and highly integrated computers. This SBC features the 22nm, Intel® Bay Trail SoC. The board provides a DDR3L SO-DIMM socket, a PC/104 connector, a PCI-104 connector, two USB 2.0 ports, one USB 3.0 port, up to two Gigabit Ethernet ports, up to two SATA 3 Gb/s ports, one dedicated HD-Audio panel connector, one VGA port, one LVDS port, up to four COM ports, one mini-PCIe slot (with one USB 2.0 port included). The CMx-BTx can be run with only 5 volts and is capable of running operating systems like DOS, Windows XP/7/8 in either 32-bit or 64-bit configuration, Linux, VxWorks, and others. Another feature included on the board is a fail safe BIOS that enables the user to start the module even if the original BIOS is corrupted.
-
Product
MIL-STD-1553 PMC Interface Module
PMC-1553
-
Avionics Interface Technologies
Dual redundant, single, dual, or quad stream configurationsTransformer & Direct Bus Coupling - Concurrent Bus Controller, 31 Remote Terminals, & Bus Monitor operation - Full error injection and detection - Multi-level trigger for capture and filtering - IRIG-B time code encoder/decoder - Ten high voltage (up to 30V) programmable DIO lines - Real-Time recording and physical bus replay - ANSI Application interface supporting C, C++, C#, and .NET development - Device driver support: Windows, Linux, VxWorks, & LabVIEW Real-Time (others on request) - Conduction-cooling and/or conformal coating available - Designed for extended temperature operations - 3.3v PMC (with 5V Tolerant I/O), 64-bit 33/66MHz - Rear (P14) and Front Panel Input/Output - Compatible with AIT’s Flight Simulyzer GUI Bus Analyzer Software
-
Product
ARINC 429 PMC Interface Module
PMC-429
-
Avionics Interface Technologies
4, 8, 16, or 32 Software Programmable Tx/Rx ChannelsProgrammable High/Low Speed Operation - Concurrent operation of all Tx/Rx Channels at high data rates - Conduction-cooling and/or conformal coating available - Designed for extended temperature operations - Rate-oriented Label Transmission - Label Selective Trigger for Capture/Filtering - IRIG-B Time Code Encoder/Decoder for Data Correlation - ANSI Application Interface supporting C++, C#, and .net DevelopmentDevice Driver Support: Windows, Linux, VxWorks, and other operating system - Compatible with AIT’s Flight Simulyzer GUI Bus Analyzer Software
-
Product
Architecture T2080 Processor
VME-196
-
Curtiss-Wright Defense Solutions
Our VME-196 combines the performance and the advanced I/O capabilities of the NXP quad-core AltiVec enabled T2080 processor. The VME-196 is supported by Curtiss-Wright’s U-Boot, Green Hills INTEGRITY, Lynx Software Technologies LynxOS, Yocto NXP SDK-based Linux and Wind River VxWorks 6.9 and 7 Board Support Packages (BSPs) and driver suite.
-
Product
Commercial and Open Source Implementation of the Object Management Group Data Distribution Standard
Vortex OpenSplice
-
Vortex OpenSplice enables data to be shared and integrated across a wide spectrum of operating systems and platforms. It provides a full implementation of both the OMG DDS latest rev1.4 (DCPS profiles) and the OMG-DDSI / RTPS v2.3 interoperable wire-protocol standards. It is targeted for use with server-class (desktops, racks etc.) platforms as well as more specialized real-time embedded environments and operating systems (e.g. single board computer running VxWorks). Vortex Opensplice is fully interoperable with Cyclone DDS, Vortex Link and and Vortex Insight .
-
Product
Extreme Rugged PC/104-Plus Single Board Computer with Intel® Atom™ Processor System-on-Chip
CM2-BT2
-
The CMx-BTx is a PC/104-based, Single Board Computer (SBC), fully compliant with the PCI-104 Specification, Version 1.1 and partially compliant with the PC/104 Specification, Version 2.6. PC/104 SBCs are very compact and highly integrated computers. This SBC features the 22nm, Intel® Bay Trail SoC. The board provides a DDR3L SO-DIMM socket, a PC/104 connector, a PCI-104 connector, two USB 2.0 ports, one USB 3.0 port, up to two Gigabit Ethernet ports, up to two SATA 3 Gb/s ports, one dedicated HD-Audio panel connector, one VGA port, one LVDS port, up to four COM ports, one mini-PCIe slot (with one USB 2.0 port included). The CMx-BTx can be run with only 5 volts and is capable of running operating systems like DOS, Windows XP/7/8 in either 32-bit or 64-bit configuration, Linux, VxWorks, and others. Another feature included on the board is a fail safe BIOS that enables the user to start the module even if the original BIOS is corrupted.
-
Product
TTEDevelopment System A664 For VxWorks 653
-
The TTEDevelopment System A664 supporting the ARINC 653 interface is an out-of-the box starter kit for integrating TTEthernet’s deterministic network technology with the time and space partitioned real-time operating system VxWorks 653. The easy-to-use and ready-to-run solution includes hardware and software as well as a Distributed IMA demo application showing deterministic communication among the different real-time operation system partitions. The system supports up to 1 Gbit/s speed, enables event-driven Ethernet (IEEE 802.3) as well as rate-constrained (ARINC 664 part 7) and hard real-time (Time-Triggered Ethernet SAE AS6802) communication on the same network with the option to synchronize IMA modules using the fault-tolerant TTEthernet network time base.
-
Product
AFDX ® / ARINC 664 Test And Simulation PCI Module
PC104p-429
-
*4 or 8 software programmable TX / RX channels*Programmable high / low speed operation*Simultaneous operation of all TX / RX channels*128 MB RAM*Label selective triggering for recording / filtering*Real-time recording and later analysis of multiple channels*Sorting according to SDI field*VXI Plug & Play driver including soft front panel*Supports: C, C ++, C # and .net*Driver support: Windows, Linux, VxWorks and other systems
-
Product
Extreme Rugged PCI-104 Single Board Computer with Intel® Atom™ Processor E3800 Series SOC
CM3-BT1
-
The CMx-BTx is a PC/104-based, Single Board Computer (SBC), fully compliant with the PCI-104 Specification, Version 1.1 and partially compliant with the PC/104 Specification, Version 2.6. PC/104 SBCs are very compact and highly integrated computers. This SBC features the 22nm, Intel® Bay Trail SoC. The board provides a DDR3L SO-DIMM socket, a PC/104 connector, a PCI-104 connector, two USB 2.0 ports, one USB 3.0 port, up to two Gigabit Ethernet ports, up to two SATA 3 Gb/s ports, one dedicated HD-Audio panel connector, one VGA port, one LVDS port, up to four COM ports, one mini-PCIe slot (with one USB 2.0 port included). The CMx-BTx can be run with only 5 volts and is capable of running operating systems like DOS, Windows XP/7/8 in either 32-bit or 64-bit configuration, Linux, VxWorks, and others. Another feature included on the board is a fail safe BIOS that enables the user to start the module even if the original BIOS is corrupted.
-
Product
HS1760/MIL-STD-1760E Network Interface Controller for PCI Express
PCIe-1760-NIC-FP
-
Avionics Interface Technologies
Configuration Variants available: PCIe-HS1760-NCNT: One NC Node and One NT Node, PCIe-HS1760-NCNC: Two NC Nodes, PCIe-HS1760-NTNT: Two NT Nodes - SAE AS5653-Compliant Network Controller/Network Terminal NIC - Unsolicited data path for handling Fibre Channel link service or non‐FC-AE‐1553 traffic - Supports DMA for high speed streaming of data - 75 Ohm single‐ended or 150 Ohm Differential coax interface – TNC connectors - Each port supports 1.0625 Gbps speed - ANSI C API interface for both NC and NT - Device driver support: Windows, Linux, & VxWorks - Quad (4) port board available on request
-
Product
6U CPCI Processor Board
CP62101
-
LinkedHope Intelligent Technologies Co.,Ltd.
CP62101, a product designed by LinkedHopeTM, is a 6U CPCI processor board based on Intel QM67/HM65 platforms supporting 2nd generation Intel i series CPU, up to 2.5GHz frequency, HD3000/2000 integrated core graphics and dual-channel SO-DIMM memory (800 /1066 /1333) with up to 16GB DDR3 ECC (optional) and up to 64GB on-board SSD storage.CP62101 provides VGA and HDMI display and supports different display terminal output. CRT displays up to 2048 × 1536. Besides, CP62101 provides a wealth of software drivers (BSP) support, including Windows7, Windows Vista, Windows XP, WES 7, VxWorks, Linux, etc., as can reduce system integration workloads and end application development efforts, so to shorten time to market.
-
Product
Shared Memory Network PCI & PCIx Interface
PCI-SMN
-
Avionics Interface Technologies
2.125 Gbps Optical loop network - Single-mode and Multi-mode optical interfaces supported - Up to 256 Shared Memory Network nodes supported - Up to 200 MByte/sec sustained data rates - Maximum 500 nS latency between nodes - Network interrupts supported - Compatible with PCI & PCIx Host System Slots - Software Drivers available for Windows, Linux, LabVIEW Real-Time, and VxWorks
-
Product
Fibre Channel Software Development Kit
Fibre Channel SDK
-
Avionics Interface Technologies
Software Drivers for Windows, Linux, VxWorks, and other Operating Systems (on request) - Compatible with all Fibre Channel Interface Modules - Includes documented APIs with source code examples for ANSI C, C++, and LabVIEW - Support provided by AITs industry leading applications engineering team
-
Product
6U Compact PCI® Single Board Computer
CP62001
-
LinkedHope Intelligent Technologies Co.,Ltd.
CP62001 is a 6U CompactPCI® single board computer designed based on Intel® GM45 chipset, compliant with PICMG®CompactPCI® specifications. There are SATAII, USB2.0, 10/100/1000Mb Ethernet, and Keyboard/Mouse interfaces on board. The display controller integrated in CP62001supports VGA and DVI dual output independently, with up to 2048×1536 resolution on CRT. Up to 4GB soldered memory on CP62001, leaves no worry about the board stability under harsh shock and vibration environment for end users. Besides, LinkedHope™ provides variant drivers BSP) support, such as VxWorks, Linux and Windows, as reduces the workload of system integration and the development of final solutions and shorten the Time-to-Market.The CP62001 with high performance/power ratio, works stably in extended temperature range, and is an ideal selection for high reliability and high availability required applications, like harsh environment communication, network security, video/image processing and can also be an ideal control unit in variant devices and equipment.CP62001 has a ruggedized version (called CP62002)with conduction cooling and wedge-lock technology. CP62002 is designed for extremely harsh environment.
-
Product
Interface
RAR15X
-
Featuring high-level API for Microsoft® Windows® 7, 8, 8.1, 10, Server 2008 and Server 2012 R1/R2 (32 and 64 bit), Linux®, Integrity, and VxWorks® that reduces application development time, standard features of the RAR15X include 8 Mbytes of RAM and 64-bit message time tagging.
-
Product
3U VPX Single Board Computer
VP32002
-
LinkedHope Intelligent Technologies Co.,Ltd.
VP32002 is a high-performance 3U VPX single-board computer, compatible with PC architecture, especially it is a China Local-design, Local-assembling product. VP32002 is an all-in-one design, supporting the 3rd generation of Intel core processors and QM77 chipset; also supports up to 16 GB onboard DDR3 memory and up to 32GB Disk-On-Modules, these features ensure its stable operation in strong shock and vibration environments. VP32002 supports a XMC interface and various I/O interface such as two SATA600 channels, two Base-BX/T GbE, two UARTs and two USB interface.The board provides a flexible PCI-Express bus interface to the backplane. The interface can be configured as follows: 1 Port x8 PCIe, 2 Ports x4 PCIe, 4 Ports x2 PCIe. This feature makes it suitable for either distributed switching system or centralized switching system.For the user to quickly form application solutions, LinkedHope provide VP32002 a complete driver package including Windows, VxWorks, Linux and QNX.
-
Product
Board Drivers
9450-DRV
-
IOWorks board drivers are Abaco Systems' IOWorks data acquisition and control (DAQC) software driver. It is a hardware and operating system-independent driver designed to support the widest variety of I/O in the industry. The driver operates with many operating systems such as Windows NT/Windows 2000, QNX, VxWorks, and Linux, and delivers high performance and flexibility across multiple platforms such as CompactPCI, VME and PCI.
