Surface Insulation Resistance Testing
testing check's PCB for shorts or current leakage between conductors.
-
Product
Transformer Insulating Oil Dielectric Tester
CXYJ-501
-
Shenzhen Chuangxin Instruments Co., Ltd.
Insulating Oil Tester is designed according to of GB-86 and IEC60156 standards.
-
Product
Digital (1kV below) Insulation Tester
1160 IN
-
Standard Electric Works Co., Ltd
● Measures insulation (MΩ), Continuity (Ω) and AC voltage.● Three insulation test voltages(DC V) : 250V, 500V, 1000V.● 3½ digital LCD (2000 counts).● 68 × 34mm ( 2.677” × 1.338” ) large LCD display.● LCD backlight display.● Automatic circuit discharge.● Test insulation at rated voltage into a 1mA load.● 200mA short circuit testing current for continuity.● Auto ranging.● Fuse protection.● Data hold function.● BS 16 edition.
-
Product
High Voltage Insulating Diagnosis Systems
DAC-6017
-
It can measure and diagnose the insulating characteristic of winding coils of high voltage electric motor, generator, and etc.It also makes possible to build in-vehicle type or stationary type in accordance with the application.
-
Product
Surface Display Unit
Multigauge 3100
-
Used with the Multigauge 3000 to provide displayed measurements on the surface. Two way communication to the Multigauge 3000. Ideal for class surveys or when visibility is poor.
-
Product
Surface Mount Temperature Sensor
SCS
-
The Series SCS Low Cost Current Switches are ideal for monitoring whether fans, pumps, or motors are operating. The current flowing through the core of the device powers the circuit without an external power supply. All models have a built in solid state output and are easy to install. Optional LED's and 10 Amp relay modules are available. The Series SCS is available in both Split and Solid Core configurations
-
Product
Hardness & Scratch Resistance
-
Hardness can be defined as a material’s resistance to permanent deformation. In the coatings industry, hardness measurement can be used to determine the resistance of the coating to scratching from general wear and tear and also if a coating is fully cured.
-
Product
Insulation & Multifunction Tester (LCD Display)
1153 AI
-
Standard Electric Works Co., Ltd
● Microprocessor-controlled.● Automatic voltmeter AC/DC at Start/Reset.● Auto range● Auto off.● Battery test.● Battery test at switch ON/Reset.● Safety voltmeter before each test.● Auto discharge on all test and all ranges.● Leads Auto-Null key.● Test Auto-Stop.● Smart hold & stop on voltmeter ac/dc.● Ener-Save feature to extend battery life.● Continuity short circuit current > 220mA.● Continuity open circuit voltage of 5Vdc.● Nominal voltage @ 1mA on all insulation ranges.● Accept 8 rechargeable batteries or Alkaline of normal.● BS 16 edition.
-
Product
Insulation Meter
HT7051
-
HT7051 has been developed to measure insulation resistance with test voltage programmable up to 5kVDC and measuring range up to 10TΩ which makes it very useful in any industrial application (tests on electric machines, power transformers, electric cables, electric boards, generic devices, etc.) within BT.
-
Product
Low Voltage Insulation Tester
AD-801
-
3 Measurement voltage ranges: 4 V, 10 V, 100 V, LCD display 3,5 digits, Autoranging, Insulation measurement up to 20 G W, LED indicator for units k W , M W and G W, Switch of choice measuring voltage 10 V and 100 V,
-
Product
Insulation Tester
-
Nippen Electrical Instruments Co.
DIGITAL METERS NIPPEN electronic energy meters are panel mounting type innovative energy monitoring devices ,having state of the art electronic microcontroller circuitry for reliability and accuracy. They can be used for 1Ø / 3Ø balanced and unbalanced loads.
-
Product
DC Air Based Resistance
-
DC Air Based Resistance Standards are designed for high accuracy resistance calibration in air.
-
Product
In-Line Test System
-
With an Averna in-line test system, clients boost production/yields, catch defects invisible to the human eye, reduce equipment downtime, and ensure repeatable results.
-
Product
Contact Resistance Meter
-
The Motwane Manufacturing Company
High contact resistance values are a definite cause of the failure or less than optimal performance in a wide variety of electrical devices. Contact resistance testing is therefore most critical to measure the resistance of electrical connections in switching devices, circuit breakers, isolators, busbars, relays, joints, connectors, cables, and cable joints. The device helps to find destructive or corroded contacts and hence protects substation devices from damage.
-
Product
4 Wire Earth Resistance & Resistivity Tester
4235 ER
-
Standard Electric Works Co., Ltd
● Microprocessor-controlled.● Earth resistivity (ρ) test.● Earth testing at 20Ω, 200Ω, 2kΩ.● Earth voltage measuring : 0-300V AC.● Automatic C spike check.● Automatic P spike check.● 2-Wire test, 3-Wire test, 4-Wire test.● LCM display.● Auto ranging.● Auto power OFF.● Data hold.● 200 measurement results can be saved in the memory and recalled on the display.● Interval between auxiliary earth spikes is 1.0~50.0m.
-
Product
Analogue (1kV below) Insulation Tester
8052 IN
-
Standard Electric Works Co., Ltd
● High quality Taut Band movement.● Three insulation test voltages(DC) : 250V, 500V, 1000V.● Two continuity test on “low ohms” : 3Ω & 500Ω.● AC voltmeter with linear scale up to 600 Vac.● 200mA short circuit current for continuity.● 1mA test current on insulation test at nominal voltage.● Automatic discharge of capacitive and inductive circuit with charge stored in the circuit under test.● Live warning and display of external voltage presence.● Fuse, air gap, crowbar and overload protected.● On line battery monitoring shows if battery is ok.● Manual zero ohm adjustment.● Low battery consumption.● Mirror scale.● Push and turn locking switch for continuous and hand free testing.● Supplied with high quality test leads.
-
Product
Digital Surface Resistance Meter
-
NEW Enclosure with Rubber Grip EdgesThinner and narrower design is easier to hold and provides protection from drops.NEW Quick Check ButtonBypasses the 15 second electrification period to allow quick spot checks.NEW Battery Compartment
-
Product
Low Resistance Test System
9100-2
-
Palico Instrument Laboratories
The Model 9100-2 measures the resistance of single or multiple battery separators quickly and accurately when used with our Model 9000-9100 Electrolyte Test Bath. This system uses a 4-terminal measurement technique which cancels the effects of electrode/electrolyte potentials.
-
Product
Meters For Contact Angle And Surface Tension
SURFTENS HL
-
Optik Elektronik Gerätetechnik GmbH
Measuring instrument for contact angle and surface free energy, special solution for semiconductor technology for wafers up to 300 mm.
-
-
Product
High Resolution Thickness & Surface Profiler for as-sawn Wafers
MX 70x
-
The MX 70x series measure Thickness, Warp, Waviness, Roughness and are usable for nanotopography.
-
Product
Non-Trip Earth Resistance Measurement
M73
-
M73 has been developed for operators who mainly work on private installations. M73 is very easy to use, it is very small in size and it carries out all necessary tests to establish COMPLIANCE (and hence ensure SAFETY) of an electric system.
-
Product
Surface Cleanliness
-
Surface cleanliness: Soluble salts & ion specific contamination (sulphates, chlorides, nitrates etc.) which are often invisible to the eye, together with amine blush (for amine cured epoxy coatings) can result in premature coating failure, resulting in high re-coating and maintenance costs. Elcometer has a range of test equipment for assessing surface cleanliness prior to applying a coating.
-
Product
Surface Analysis
Dimension AFP
-
The Dimension AFP is the world's only fab-based metrology tool specifically designed for both CMP profiling and etch depth metrology for current and advanced technology nodes. The system combines the superb resolution of an AFM with the long-scan capability of an atomic force profiler tomonitor etch depth and dishing and erosion on submicron features with unsurpassed repeatability.
-
Product
PID Insulation Tester
TOS7210S
-
The PID insulation tester (TOS7210S) is designed based on the insulation resistance tester (TOS7200) to carry out the evaluation of the PID (Potential Induced Degradation) effect of the PV module precisely and efficiently. Being equipped with the output ability of 2000 V and the ammeter with nA resolution as well as a polarity switching function, the TOS7210S is also applicable not only to the PID evaluation but also the evaluation of the insulators that requires a high sensitivity of measurement. The tester is equipped with the panel memory that is externally accessible and RS232C interface as standard; it can be flexibly compatible with the automated system.
-
Product
Resistivity Meter of Powder Composites
RM-200
-
The resistivity meter is fully automated and does not required any adjustments. The measurement is made by using the four-point contact probe on the ring (ø60 x ø50 x 5mm) and rectangular prisms samples (6 x 6 x 60÷80mm). The measurement results are automatically saved in meter memory, what allows user to manage of data. The RM-200 contain series connection which allow the data transmission to PC.
-
Product
Optical Tactile Surface Finish
1000Z
-
The Adcole Model 1000-Z features both optical and tactile measuring heads to deliver high precision surface measurements of camshafts, crankshafts and turned parts. The non-contact interferometric probe greatly expands on the measurement capabilities from the diamond tipped contact probe of the standard Adcole 1000 gage, as the optical accessory can precisely measure surface finish of cam track groove sidewalls, cam track bottom grooves and more. Profilometers such as the 1000-Z quantify surface roughness and are relied on to maintain quality and identify potential problems in the manufacturing and coating process.
-
Product
IEC60529 IPX1/2 Rain Resistance Tester
IPX12A-600
-
Shenzhen Chuangxin Instruments Co., Ltd.
The IEC60529 IPX1/2 Rain Resistance Tester is designed according to the <> of IEC60529 standard, GB7000.1 and GB4208-2008. IEC60529 IPX1/2 Rain Resistance Tester is mainly used to simulate the product under the condition of the rain climate to test the products’ physical properties.
-
Product
Automated Temperature Resistance Standard
-
Measurements International Ltd.
Exceptional Stability, Cost-effectiveness, Performance-based Results, 10 Ω, 25 Ω, 100 Ω, 200 Ω, 400 Ω and 1000 Ω Internal Standards, Built-in Temperature Chamber for Optimal Performance.
-
Product
Ground Resistance Inspection Box
-
AllWin Instrument Science and Technology Co., Ltd.
Check the ground resistance tester each time prior to start work everyday morning and do some relevant records.
-
Product
Digital Surface Profile Gauge
224
-
Measurement capability to ±5%Can be used in accordance with National and International StandardsTemperature stable measurementsStatistics are calculated and displayed in real timeLive and batch readings graph format for instant analysis
