Battery Cycle
-
product
HEV/EV Battery Equipment
Our line of HEV / EV Battery Equipment combines sophisticated electronics, advanced technology, and user-friendly operation. The EVc Battery Reconditioner processes all types of nickel metal hydride HEV batteries. Worldwide, the EVc has proven to be a neccesary workhorse for any hybrid auto shop or garage. The EVd Power Tester monitors individual module voltages during high power battery discharge. The EVd also features a "smart" charger that performs complex CCCV charging. We are currently developing technology to process and rebalance the Li-ion batteries for electric vehicles.
-
product
Battery Test device
ATGB 1200
The ATGB 1200 is a battery tester for all standard battery technologies aimed at quality assurance, production and product development. Advantages of the ATGB: Creation of customized test sequences. Generation of load curves and peaks. Temperature measurement at the battery
-
product
PXI Battery Simulator Module
41-750-001
The 41-750 is a battery simulator module that can be used to simulate the power supplies of cellular phones and other portable battery devices. It features fully floating output terminals than can deliver voltages up to 6 Volts. The fast responding remote sense connections allow the module to regulate the supply voltage at the device under test.
-
product
Battery Gauges
Global Digital Instruments, LLC
Our battery fuel gauges and LED volt meters are designed to monitor the charge capacity of DC powered equipment and monitor information about the equipment's electrical system.
-
product
Battery Temperature Test Chamber
Sanwood Environmental Chambers Co ., Ltd.
Sanwood climatic chambers for battery can be tested under controlled temperature and humidity conditions, similar to the conditions under which batteries operate during their lifetime.
-
product
0-10V Battery Voltage Sorter Tester
TOB-0918
Xiamen Tob New Energy Technology Co., Ltd
0-10V Battery Voltage Sorter Tester With Battery Low/High Voltage Alarm For All Kinds Of Batteries. TOB-0918 Battery voltage tester is a Voltage sorter with single-chip control of portable test instrument, This voltage tester is with a voltage limit set and automatic judging function, we can set the voltage in the range or out the range alarm function.
-
product
Motorcycle Battery Testers
ELAK Motor-Cycle Battery Testers are designed for testing batteries used in motor-cycles, scooters, ATV''s, etc. These testers check the voltage drop of the battery under a fixed load and confirm the status of the battery full, weak or dead. The new generation motor-cycle and scooters are fitted with an electrical start. It is therefore very essential to test these batteries under load, to ensure that the batteries are capable of starting the vehicle.
-
product
Automatic Battery with Filters with Standard Contactors
BATLVF600
Lifasa - International Capacitors, SA
LIFASA automatic capacitor banks are used for centralized compensationof power factor in low voltage instalations.
-
product
Battery Charge and Discharge Tester
HTCFD / 790
Wuhan Huatian Electric Power Automation Co., Ltd.
The voltage monitoring information of single battery is simple, safe and accurate with wireless relay access.
-
product
Battery Pack Power HIL Testbed
8610
Chroma ATE launches the 8610 Battery Pack Power HIL Testbed for testing battery systems and components of new energy vehicles, incl. the battery module, battery management system, and cooling/heating system. Various hardware options are available for integration, such as a DC power supply, battery charge/discharge system, digital meter, Hi-Pot tester, and short-circuit and overvoltage protection devices.
-
product
Wireless Battery System Tester
EECS550
Snap-on Tools has launched the new Snap-on EECS550 Wireless Battery System Tester that eliminates the need for a second technician. “The EECS550 maximizes manpower and gets the critical job of battery system testing done with just one set of hands,” says Dave Brekke, product manager for Snap-on. “Snap-on has listened to techs in shops where this work is a daily task. The tester will change the way techs are able to service cars, trucks, motorcycles, golf carts, ATVs and more. From the strong, built-in magnets that hold the tester in place to the easy-to-see, back-lit screen that displays in eight languages and reports battery, starting and charging system conditions, this tester takes productivity to the next level.”
-
product
Lead-acid Storage Battery Analyzer
From the beginning of 2006 the verification of measurements of the analyzer of lead-acid chemical sources developed by Company "Megaron" is spent in Test laboratory "Neva-Reglament". The analyzer is intended for the express-estimation of a condition of lead-acid batteries: before the first use of new battery (an estimation of the electric characteristics declared by the manufacturer); during the battery operation (an estimation of a condition and working capacity at real application).
-
product
Battery (EV) Automatic Test System
Landrex Technologies Co., Ltd.
Battery (EV) Automatic Test System
-
product
Battery Test Systems
Low current model32 channel battery cycler (expandable up to 128 channels)No. of minimum channel : 16 channelsmax. voltage range : ±5Vmax. current range : ±10
-
product
System Controllers & Battery Monitors
UNIPOWER System Controllers & Battery Monitors provide battery management functionality for the Aspiro, Guardian and Sageon DC Power Systems. The proprietary PowCom software enbles the user to monitor multiple Aspiro or Guardian systems at different locations using a highly intuitive GUI. SageView software provides similar fucntionality for Sageon systems and also works with the standalone Sageon Shield battery monitor.
-
product
Multiple Cell Battery Chargers
Renesas' highly versatile battery charger ICs support devices with rechargeable 2, 3 or 4-cell batteries and include configurations such as a hybrid power boost (HPB), narrow output voltage DC (NVDC), buck-boost NVDC, and SMBus Level 2.
-
product
Shock Test System, Battery Test
Guangdong Bell Experiment Equipment Co.,Ltd
DGBell's shock test system used to measure and determine the impact resistance of a product or package. It is mainly used to evaluate the reliability of the function and the integrity of the structure of the test product under impact environment. Suitable for impact testing of aerospace, aerospace, marine, military, consumer electronics, automotive, household appliances and display equipment.
-
product
Battery Tester
CS-3001
The CS-3001 test system records all block voltages, total voltage and current during a discharge test. The modular design makes it easy to connect most of all battery installations, starting from a single block and ending up with 960 block voltages. Up to four parallel strings can be tested. All measuring modules are electrically isolated (600VDC CAT III, 5000VAC test voltage).
-
product
Battery Discharge Test Unit
125V DC 100A
KV Hipot Power Test Equipment Co.,Ltd
Battery Discharge Capacity Tester is used to perform discharge testing which is the verifiable method to determine actual capacity of battery systems.
-
product
EIS Battery Analyzer
BA8100
The BA8100 is designed to accurately measure the internal impedance of a single cell or battery stack with voltages as high as 80 V. In addition to impedance, auxiliary measurements include voltage, current, phase, capacitance, inductance, quality factor and more. With the provided software, the BA8100 can perform Electrochemical Impedance Spectroscopy (EIS) across a frequency range of 50 mHz to 10 kHz. The impedance spectrum can be evaluated through the Nyquist and Bode plot tools to determine effective series resistance (ESR) and track battery health. Included with the BA8100 is a self-test fixture to verify the instrument’s performance or compensate for resistance introduced by the test leads.
-
product
Battery Cell Simulator
BCS-LABCAR
The ETAS Battery Cell Simulator (BCS-LABCAR) is a Hardware-in-the-Loop system which specifically targets the signal-level test, validation, and calibration of battery management systems (BMSs). The BCS-LABCAR is a high-precision Battery Cell Simulator that emulates the behavior of individual battery cells and packs across a wide range of challenging operating conditions, e.g. cell balancing over-charging, deep discharging, or pulse operation. The system is highly modular and thus scalable to emulate battery packs from a single cell all the way up to 200 cells.
-
product
Battery Service
Wireless battery and electrical system analysis tablet using Adaptive Conductance, an advanced battery analysis method that produces a more accurate examination of the battery’s cold cranking ability and reserve capacity, vital to determining a battery’s true health. The 7-inch Android touchscreen tablet can display a quick health status of the existing battery, register a new battery and perform advanced battery and electrical system diagnostics.
-
product
Battery Management Systems Testing
A Battery Management System (BMS) is an embedded unit performing critical battery functions, including cell monitoring and balancing, pack charge and discharge control, safety, and communications. The BMS must be tested early in development to optimize control algorithms, as well as during manufacturing to ensure reliable functionality. Bloomy’s family of BMS test systems provides a consistent platform for engineers to bring a BMS to market faster, and more reliably.
-
product
Temperature Cycling Test Chamber
Guangdong Bell Experiment Equipment Co.,Ltd
DGBELL Temperature cycling test chamber is suitable for testing various performance indexes of aerospace products, electronic instruments, materials, electronic products and various electronic components under the condition of rapid temperature change.
-
product
Battery Crush Nail Penetration Tester
Guangdong Bell Experiment Equipment Co.,Ltd
DGBell's Battery Crush Nail Penetration Tester is used to simulate the battery penetration test of a sharp object during packaging, transportation, storage, use and disposal.
-
product
Fully Filtered and Stabilized Battery Eliminators
Series TBC
Kepco's TBC are designed as battery chargers, for float-equalize service to maintain battery arrays such as are found in many telecommunication installations. The TBC are fully filtered and stabilized battery eliminators that also find application as burn-in power supplies. Nine models are available.
-
product
Material Research Battery Tester
BTS9000
Shenzen Neware Electronic Co LTD
BTS9000 is the most advanced battery testing instrument from Neware, it's the best choice for material research, but some customers think BTS9000 is a little expensive. Thus, we developed BTS9000-2CH for people who want to get high accuracy and high speed with low price.
-
product
Battery Voltage Supervisor
BVS
DV Power battery voltage supervisor – BVS, is an accurate battery voltage monitoring system that monitors the state of health of battery systems. It records important battery parameters such as battery voltage, inter-cell connection voltage, and ambient temperature. Because of that, it can be a support tool for capacity testing.The BVS voltage supervisor is an integrated system consisting of:BVS Control Unit (BVS-CU)Cell Voltage Modules (CVM)String Voltage Module (SVM) (optional)String Current Module (SCM) (optional)It is an ideal testing tool for maintenance, troubleshooting and performance tests on individual stationary batteries and battery packs in critical backup energy solutions.BVS-CU provides ambient temperature measurements on multiple locations (4 temperature channels). Overall string voltage and string current monitoring can be achieved by using an optional string voltage module (SVM) and string current module (SCM).There are two types of DV Power battery voltage supervisors:BVS – One cell voltage module measures 1 cellBVS-4 – One cell voltage module measures 4 cellsCVM modules detect cells that fail a discharge test based on monitored voltage values. As a result of that, these cells can be safely removed from the battery string.Data acquisition and analysis of data collected from the modules are available in the DV-B Win application software suite. They provide data viewing, tracking, and generation of comprehensive reports.
-
product
Dual channel battery charger and analyser
TS25 MKII
Rugged and reliable designed for busy maintenance workshops, the TS25 MKII charger is suitable for every industry where batteries are used. It features a software controlled self-calibration facility which amounts to zero downtime for calibration.
-
product
Traction Battery Short Circuit Test Machine
Guangdong Bell Experiment Equipment Co.,Ltd
Traction Battery Short Circuit Test Machine Relevant standards requirement:Single Storage Cell Safety Test6.2.4 Short circuitCharge the single storage cellaccording to 6.1.3 standardThe cellis to be short-circuited by connecting the positive and negative terminal with a external resistance of less than 5mΩ for 10 minObserve for 1HBattery module safety test6.3.4 Short circuitCharge the battery module according to standard 6.1.4The battery module is to be short-circuited by connecting the positive and negative terminal with a external resistance of less than 5mΩfor 10 minObserve for 1H





























