Prototype Boards
-
Product
PXI, CPCI Development And Prototyping Board
TE2100
-
Team Solutionsí PXI Development and Prototype board is the fastest road for system integrators to deliver a PXI customized product and provides design engineers with a speedy avenue to release PXI based prototypes and products.
-
Product
HES Prototyping Boards
-
HES™ is a feature-rich family of SoC/ASIC pre-silicon physical prototyping and hardware emulation boards. The family features boards with high-performance devices from either Xilinx (including Virtex-7, Virtex UltraScale, Virtex UltraScale+ and Zynq UltraScale+) or Microchip (PolarFire and SmartFusion2).
-
Product
Boundary Scan Test
-
Boundary Scan is a very useful tool for quick, low-cost, re-usable powered-up test of an assembly for basic functionality. Because a fixture with test probes is not required, it is possible to have a working test available within hours or days, rather than weeks. Designers can receive rapid feedback on their prototype boards with tests that can be used again during production testing, as well as for device programming. Given power, ground and Tap port signals, tests can be written to assess the performance of the boundary scan enabled parts on an assembly and other parts on the boundary scan chain.
-
Product
RF Prototyping Kit
VXI-5501
-
* VXI-5501 has a Bare Copper-clad Prototyping Board for RF and microwave modules.* Includes a VXI-5524 Register Based Interface Board with 48 digital IO lines and a 16-bit VXI data bus.* User configurable model number, manufacturer ID, version and serial numbers identifies the module as from your company.* Includes a blank front panel, side shields, manual, layout aids and VXI-Kit hardware for a single slot wide C-size module.
-
Product
Digital System X
DSX
-
We have developed this technology, not only for our customers, but for our own unique needs in the areas of prototyping and test. We found that many of the standard digital prototyping boards (FPGAs, PLDs, etc…) that are available on the market, did not have the flexibility or the base architecture to provide the prototyping capabilities we need in developing our own solutions.
-
Product
Design for Test
-
Test Coach offers Design for Test (DFT) consulting to assist customers with design review of prototype boards prior to release for production. Design for Test analysis is extremely important in ensuring that an assembly will achieve the highest possible test coverage. For ICT, this DFT will review the board to confirm that the bed-of-nails test fixture can be fabricated to test an assembly without sacrificing test coverage. As with ICT, Flying Probe benefits from DFT analysis by reviewing test point access and mechanical challenges that may affect the potential test coverage. Completing a DFT enables Test Coach to make recommendations to our customers that may be implemented on boards during the design phase which will allow for the most comprehensive coverage at time of test.
-
Product
EIA Based VectorPak
-
VECTOR Electronics and Technology, Inc.
VectorPak™ subracks offer versatility within a 19” rackmount format. All racks are adjustable in both height and depth, offering standard product solutions for standard and custom requirements. All Subrack sizes are compatible with Vector prototyping boards (see Vectorbord® Plugbord™ section), and can accommodate other sizes as well.
-
Product
Prototyping Kit
VXI-5502
-
* VXI-5502 has a Sea-of-holes Prototyping Board with multiple power and ground planes for analog and digital prototyping applications.* Includes a VXI-5524 Register Based Interface Board with 48 digital IO lines and a 16-bit VXI data bus.* User configurable model number, manufacturer ID, version and serial numbers identifies the module as from your company.* Includes a blank front panel, side shields, manual, layout aids and VXI-Kit hardware for a single slot wide C-size module.
-
Product
TySOM Embedded Prototyping Boards
-
TySOM™ is a family of embedded system prototyping boards. Depending on the board, one of three FPGAs will be at its heart: a Xilinx Zynq® UltraScale+™, a Xilinx Xilinx Zynq-7000 or a Microchip PolarFire SoC. The boards are compatible, through industry standard interfaces (FMC or BPX), with Aldec’s wide range daughter cards, making Aldec’s TySOM embedded prototyping boards ideal for the rapid development of applications that include automotive (and ADAS, in particular), artificial intelligence (AI), machine learning (ML), embedded vision, embedded-HPC (including edge-processing), IoT, IIoT and industrial automation.
-
Product
Supported Test Systems
-
TTCI is a leading solutions provider of application development for test systems from Seica, Keysight, Teradyne, Digitaltest, and XJTAG. We offer a wide variety of testers and test solutions to meet your needs. Our Seica Pilot and Digitaltest Condor flying probe systems can handle all of your low- to mid-volume production, prototypes, and PC boards with accessibility issues. The Keysight 3070 and Teradyne TestStation can address your larger production runs and fixture requirements. In addition, we can also address your functional and boundary scan needs.
-
Product
RF/MicrowavePrototyping Boards and Housings
MicroAmp2
-
MicroAmp2 is a new series of RF/microwave prototyping boards and housings that allow for rapid construction of custom circuits in a fraction of the time and cost of traditional solutions. With the MicroAmp2 series of MB boards, a designer can quickly build amplifiers, filters, passive networks, multipliers, prescalers, log detectors, oscillators, and opamps using many popular components. A growing line of MB circuit boards are available to fit many of the industry-standard components, which can be easily assembled and mounted into shielded RF housings to create fully functional modules. Select parts from popular manufacturers such as Analog Devices, Avago, CEL, M/A-COM, Mini Circuits, RFMD, Triquint, and others.
-
Product
Software
HES Proto-AXI
-
The HES Proto-AXI™ software package, when combined with our HES™ prototyping boards, provides an efficient and robust environment for rapid design prototyping and/or algorithm accelerator development and bring-up.
-
Product
DUT Prototype Board
DPB8800
-
The DPB8800 is an 11? x 14? PC board used to interface the tester with the Device Under Test (DUT). This board contains generous area for custom circuitry and extra relays. The DPB8800 is also available with standard solutions to test families of components like Op-Amps, Regulators, ADC?s and DAC?s. +/-15 V and +5 V are available to support circuitry biasing.
-
Product
VXI Prototyping Kits For RF Modules, Analog And Logic Circuits
-
• VXI-5501 has a Bare Copper-clad Prototyping Board for RF and microwave modules.
-
Product
Prototype PCBS Printed Circuit Boards
-
Prototype printed circuit boards are manufactured for a variety of reasons; often it is important to manufacture these circuit boards to perform various tests before going through with a full PCB production run. When it comes to prototype PCB boards it’s important to get them made using high quality standards.
-
Product
PXI Prototyping Module, 1-Slot, 9-Pin D-Type
40-225A-701
Prototyping Module
The 40-225A PXI Prototyping Modules are stripped down versions of the 40-220A PXI Breadboard series. These are very basic, low cost prototype modules. They have no PXI interface but do have access to fused power supplies from the PXI backplane.
-
Product
PXI Prototyping Module, 1-Slot, 20-Pin GMCT
40-225A-801
Prototyping Module
The 40-225A PXI Prototyping Modules are stripped down versions of the 40-220A PXI Breadboard series. These are very basic, low cost prototype modules. They have no PXI interface but do have access to fused power supplies from the PXI backplane.
-
Product
PXI Prototyping Module, 1-Slot, 78-Pin D-Type
40-225A-401
Prototyping Module
The 40-225A PXI Prototyping Modules are stripped down versions of the 40-220A PXI Breadboard series. These are very basic, low cost prototype modules. They have no PXI interface but do have access to fused power supplies from the PXI backplane.
-
Product
PXI Prototyping Module, 2-Slot, 9-Pin D-Type
40-225A-702
Prototyping Module
The 40-225A PXI Prototyping Modules are stripped down versions of the 40-220A PXI Breadboard series. These are very basic, low cost prototype modules. They have no PXI interface but do have access to fused power supplies from the PXI backplane.
-
Product
PXI Prototyping Module, 1-Slot, 96-Pin Micro-D
40-225A-101
Prototyping Module
The 40-225A PXI Prototyping Modules are stripped down versions of the 40-220A PXI Breadboard series. These are very basic, low cost prototype modules. They have no PXI interface but do have access to fused power supplies from the PXI backplane.
-
Product
PXI Prototyping Module, 2-Slot, 37-Pin D-Type
40-225A-202
Prototyping Module
The 40-225A PXI Prototyping Modules are stripped down versions of the 40-220A PXI Breadboard series. These are very basic, low cost prototype modules. They have no PXI interface but do have access to fused power supplies from the PXI backplane.
-
Product
Breadboard to DAQ Converters
0001026-1 / -2
-
VI Control Systems has designed two converter boards that make it easy to connect data acquisition boards to breadboards and allow easy computer control and monitoring of prototyped electronic circuits. The converter boards are 0.8 x 3.5 inches and have silk-screened pin numbers for every pin on the board. The 68-pin SCSI converter can also be used to connect 68-pin SCSI cables to prototype solder boards that have 0.1 inch centers.
-
Product
PXI Prototyping Module, 1-Slot, 37-Pin D-Type
40-225A-201
Prototyping Module
The 40-225A PXI Prototyping Modules are stripped down versions of the 40-220A PXI Breadboard series. These are very basic, low cost prototype modules. They have no PXI interface but do have access to fused power supplies from the PXI backplane.
-
Product
PXI Prototyping Module, 2-Slot, Dual 20-Pin GMCT
40-225A-812
Prototyping Module
The 40-225A PXI Prototyping Modules are stripped down versions of the 40-220A PXI Breadboard series. These are very basic, low cost prototype modules. They have no PXI interface but do have access to fused power supplies from the PXI backplane.
-
Product
Motion Control Terminal Board For Panasonic MINAS A4 Servo Amplifiers
DIN-814-A40
Terminal Board
- Panasonic MINAS A4 super servo- Dimensions: 123 mm x 107 mm x 44 mm (WxLxH)- Available for PCI-8174, PCI-8164, PCI-8154, PCI-8158 and PCI-8134
-
Product
PXI Prototyping Module, 2-Slot, 15-Pin D-Type
40-225A-602
Prototyping Module
The 40-225A PXI Prototyping Modules are stripped down versions of the 40-220A PXI Breadboard series. These are very basic, low cost prototype modules. They have no PXI interface but do have access to fused power supplies from the PXI backplane.
-
Product
Dual LGA3647-P0 Intel® Xeon®Scalable EATX Server Board with 12 DDR4, 5 PCIe x16 + 1 PCIe x8 + 1 PCI, 8 SATA3, 6 USB3.0, Dual 10GbE, IPMI
ASMB-925
Server Board
- EATX Server Board with dual Xeon Scalable processors- DDR4 2933MHz RDIMM up to 1.5TB, support Intel Optane DC Persistent Memory- Five PCIe x16 (Gen3), one PCIe x8 (Gen3), and one PCI slot- Intel® X557-AT2 dual 10GbE ports- Eight SATA3.0 and six USB3.0 ports- 0 ~ 40 °C ambient operation temperature range
-
Product
LGA 4189 Intel® Xeon® Scalable Proprietary Server Board with 16x DDR4, 4 x PCIe x16, 10 x SATA3, 8 x USB 3.2 (Gen 1), Dual 10GbE, and IPMI
ASMB-976
Server Board
- LGA4189 proprietary server board with 3rd Gen Intel® Xeon® scalable processor- DDR4 3200 MHz RDIMM up to 2TB supports Intel® Optane™ Persistent Memory- 4 x PCIe x16 and 7 x PCIe x8- Intel® X550 dual 10GbE ports- Ten SATA3 and two M.2 connectors (SATA/PCIe compatible)- 0 ~ 40 °C ( 32 ~ 104 °F) ambient operating temperature range
-
Product
Carrier Boards
ROM-DB5901
Carrier Board
ROM-DB5901 is an evaluation carrier board designed for the Advantech SMARC v2.0 module. It is compatible with the ROM-5720, ROM-5620 and ROM-5721 SMARC modules and has a multiple I/O interface for evaluation and development. It supports wide range operating temperatures, two power input interfaces, and two MIPI connectors for the camera module. ROM-DB5901 is an ideal development board for mobile applications, such as portable devices, industrial tablets or HMI systems
-
Product
Quad QSFP28/QSFP+ FMC+ Module
FPGA Board
iWave’s QSFP28/QSFP+ 2×1 Stacked FMC+ HSPC Module is designed to meet VITA 57.4 FMC+ Standard. This FMC+ Module is supported by two stacked QSFP28/QSFP+ ports(Upto400G) with 4-Bit Silicon Labs programmable clock synthesizer (default = 156.25Mhz). A flexible reference clock for on the QSFP28/QSFP+ 2×1 Stacked FMC+ Module is fully programmable over the 0.16 to 710 MHz range through I2C. Each QSFP28/QSFP+ ports are directly connected to four multi-gigabit serial transceivers banks of Vita 57.4 compliant carrier Board.
