Power Test Systems
-
Product
Test System Mainframe
ITC59000
-
The ITC59000 Test Platform is a desktop DynamicParametric Test System mainframe. The ITC59000Test Platform accepts up to four Test MeasurementUnits (TMUs) that perform transient measurements onsemiconductor devices such as power MOSFETs,IGBTs, and diodes.
-
Product
PXI Instrumentation Modules For Automated Test Systems
-
PXI-based test systems often require a variety of general-purpose instrumentation such as digital I/O, waveform generators, voltage & current sources and DUT power supplies.
-
Product
High Voltage Switching Test System
-
The advanced development of new technologies, such as SiC and GaN, have opened the opportunity for more efficient and higher voltage/power performance in switching and power management circuits. Their high cutoff frequencies, low on-state resistance, and very high breakdown voltages can increase power supply power handling densities approaching hundreds of watts/inch. Reliability of these new technologies and techniques is critical for realizing practical applications. While Silicon devices have a rich history of proven reliability, these newer compound semiconductor technologies are too new to have a reliability history and have not been well proven. Further, process variations, even in well-controlled lines, yield widely varying results. This has driven the need for additional testing and to burn-in devices prior to delivery.
-
Product
FADEC/EEC Test Platform
Test Platform
The FADEC/EEC Test Platform provides a hardware in-the-loop (HIL) closed-loop test environment for dynamic and maintenance testing of full-authority digital engine control (FADEC) and electronic engine control (EEC) units of both rotary- and fixed-wing airframes. The system simulates one or more turbofan engines, including its sensors and actuators for use with the most sophisticated FADECs and EECs on the market. The system delivers repeatable, cost-effective testing in a fraction of the time needed with typical in-house simulation test systems.
-
Product
Electrodynamic Vibration Test Systems
PET-series
-
Vibration controller: Enables complicated vibration tests being coupled with the vibration controller.
-
Product
Circuit Breaker Test Systems
-
Crest has over a decade of experience of designing and manufacturing test systems for testing all the different kinds of switchgear and controlgear.
-
Product
Measurement System For Testing & Binning Of Back-End LEDs
TP121-TH
-
The photometric specifications of LEDs must meet very high tolerance requirements regardless of whether they are to be used in general, automotive or other specialist lighting applications. This is often a problem since the manufacturing tolerances of LEDs can be higher than those permitted in the end-use applications. Also, LED binning by LED manufacturers in order to classify LEDs based on their tolerances is performed with flash mode testing using pulsed current flow. However, end-use applications of the LEDs often operate in constant current mode and with significant thermal effects. The sophisticated LED processing industry therefore requires measurement devices that can be used for both manufacturer-compliant pulsed mode, as well as constant current operation mode. When the LEDs are run in constant current mode, the junction temperature has significant influence on the performance and lifetime of the LED. Therefore, test systems should be able to test the LEDs at specific junction temperatures.
-
Product
Complete Power Analysis System
PK3564-PRO+
-
PK3564-PRO+ complete Power Analysis System includes PS3550 Power Analyzer, AC charger, Quick-Start manual, deluxe voltage leads, four eFX6000 flexible current probes, SD memory card, PSM-A Software, Mini Line-to-DC Converter, Bluetooth Adapter, USB Communications Cable, CASW Weather-Resistant Carrying/Operating Case, and 2-year deluxe warranty.
-
Product
Wireless System For Test And Measurement
TM400 Compact
-
The TM400 system was designed to provide the ideal link between calibrated test microphones and measurement equipment such as SIM®, SIA SMAART Live®, TEF® or other systems. By using a radio link, long cables can be eliminated thus saving time and providing opportunities for additional measurements to increase accuracy. The microphone can even be moved around in the venue while the audience is present – something that is impossible with a cabled measurement microphone.
-
Product
Power Supply Series
HMP2000
Power Supply
The R&S®HMP DC Power supplies are primarily designed for industrial use. With two or three output channels and up to 10 A output current, these rugged instruments are ideal for a wide variety of applications. They offer high efficiency with low residual ripple and many protection functions.
-
Product
Lamp Cap Temperature Rise Test System
CX-T1
-
Shenzhen Chuangxin Instruments Co., Ltd.
Lamp Cap Temperature Rise Test System is according to IEC60360-1998 and GB2512-2001(Standard method of measurement of lampcap temperature rise). It is used to test the working and environmental temperature as well as temperature-rise of the burner and lamp. It meets the requirement of IEC and GB Standards
-
Product
ESD & Latch-Up Test System
-
Identify and help correct ESD and latch-up susceptibility issues on sensitive integrated circuit components prior to full-scale production with the Thermo Scientific™ MK.2-SE ESD and Latch-Up Test System. The MK.2-SE test system provides advanced capabilities to test high pin count IC devices to Human Body Model (HBM) and Machine Model (MM) ESD standards. The system’s pulse delivery design addresses wave form hazards such as trailing pulse and pre-discharge voltage rise, and performs Latch-Up testing per the JEDEC EIA/JESD 78 Method.
-
Product
Pneumatic Horizontal Shock Test System
KRD12 series
-
The KRD12 series shock test system is used to measure and determine the horizontal impact resistance of a product or package, and to evaluate the reliability and structural integrity of the test unit in a horizontal impact environment. The system can perform conventional half-sine wave, post-peak sawtooth wave, or trapezoid wave shock test to realize the shock energy that the product is subjected to in the actual environment, thereby improving the product or packaging structure.
-
Product
Test Case Management System
Kiwi TCMS
-
The leading open source test case management system. *Efficiently manage test cases, plans and runs*Improve testing productivity & reporting*Integrates with popular issue trackers*External API interface*GPL 2 licensed
-
Product
Horizontal Vibration Test Systems
G-3 Series
-
This series was used for the special structure of airbearing guide of inspection for Seismic Detectors andcharacterized is large displacement and high-accuracywaveform. In addition, the use of the Windows seismicdetector controller is easy to operate it.
-
Product
Power, Patchcord, Receiver, 72", Micro Power, 12 AWG White, Single Ended ( 22 Amps)
7-252912000-072
Power Patchcord
Power, Patchcord, Receiver, 72", Micro Power, 12 AWG White, Single Ended ( 22 Amps).
-
Product
Environmental Test Systems
-
Manufactured products can be exposed to both thermal and mechanical stresses.These should not be considered separately, as the effects may be linked.IMV can supply vibration-test systems combined with climatic chambers to provide complete vibration, temperature and humidity environmental testing.These systems can be custom-designed to meet your application.
-
Product
16-Station Testing System
-
The ElectroPuls 16-Station testing system performs high cycle fatigue testing on multiple samples simultaneously, with a fatigue-rated load cell included on each station. The fixture uses a carousel designed with high stiffness and low mass to enable high frequency testing and reduce test time.
-
Product
(1000kN) Fatigue Testing Systems
8805
-
The 8805 is a 4-column, 1000 kN servohydraulic fatigue testing machine. It features a high-stiffness and precision-aligned load frame, with hydraulic lifts and locks, and an actuator in the upper crosshead.
-
Product
Power Systems
-
Astronics serves global customers as the aircraft industry’s electrical power experts, offering a breadth of power and motion solutions for commercial transport, business, VIP, rotorcraft, military aircraft, and other airborne platforms. Whatever your program, you’ll find a proven, certified solution with Astronics.
-
Product
Automated Test System
-
Automated Test System is a production-ready solution that combines test software and various hardware for validation test in both manufacturing and R&D. The solution provides a high performance and cost-effective system based on National Instruments technology.
-
Product
Marine Shaft Power Meter Systems
-
Datum’s Marine Shaft Power Meter Systems are developed to provide real time and ongoing power monitoring data on propulsion shafts, thrusters and diesel generators. These devices are commonly used for fuel economy monitoring and equipment maintenance planning programs and can be used in conjunction with our EEXI | ShaPoLi solution to keep vessel owners in line with the latest legislation.
-
Product
Power System Analysis Software
DSATools
-
DSATools™ is a suite of leading-edge power system analysis tools that provides the capabilities for a complete assessment of system security, including all forms of stability. DSATools™ offers a complete toolset for power system planning and operational studies. In addition to rich modeling capabilities and advanced computational methods, the software is packed with useful study tools that enable significant productivity improvements.
-
Product
HVDC Power Filter Characteristic Test Set
FT3000
-
FT3000 Power Filter Characteristic Testing equipment has the functions of automatic sweep harmonic signal output, A-F and P-F characteristic measurement/display etc. It can perform HVDC Power Filter Testing and is mainly used in AC filter of DC convertor station, DC filter tuning characteristics test and parameter test of R, L and C. It is also used in electrified railway HV filter, passive power filter client and conventional AC substation reactive compensation device.
-
Product
ARTES Automatic Relay Test Systems
-
The purpose of power system protection is to use accurate and reliable protection devices to detect faults promptly and without fail and to minimize impairments to the power supply by selectively switching off faulted sections of the system.The use of suitable protection devices can significantly improve the safety and reliability of complex electrical power systems and installations. Regular testing is the only way to ensure that these protection devices function correctly throughout their operational life.More than 20 years of experience in developing and manufacturing automatic relay test systems have gone into creating the third generation of ARTES test instruments. Back in 1996, KoCoS was the first company to present Windowsbased testing software for controlling and operating test equipment and the company continues to play a pioneering role in the design of clearly structured and ergonomic user interfaces today.
-
Product
Computer-controlled Torque Testing System
Torque Testing System,
-
Our top-of-the-range Vortex-i torque testing system gives optimum testing performance and evaluation options, enabling you to get the most from your test measurements.
-
Product
Mobile Testing Power Supply(Microamp)
M8831
-
M8831 Power supply, a new generation of programmable linear power supply, are designed with high speed dynamic programming output(Voltage 0-30V, 1ms rising time), high current accuracy (0.001mA resolution) and low internal resistance, which can satisfy all the test requirements. The combination of bench-top and system features in these power supplies not only make it possible to option into other equipments, but also make it possible for users to edit program by panel keyboard, which will bring much convenience to users. Meanwhile, the voltage level switch works without relay, which will cause the fast switch between high voltage and low voltage. Moreover, M8831 powr supply provides the best solutions for cellphone research, micro-electronics lab,research institue and special users requiring power supply with low current buthigh accuracy .
-
Product
Low Voltage Burn-in and Test System
Max 450
-
For burning-in and testing DUTs such as microprocessors, DSPs and logic devices, which require low voltage. Output monitoring gives functional test results for every device during burn-in
-
Product
Automated Testing Systems
-
Instron’s automated testing systems bring precision, productivity, and safety to materials testing by automating routine tensile, flexural, and compression operations. Available as full turnkey platforms or modular add-ons for existing test frames, these systems — including the AT3 three-axis, AT6 six-axis robotic, AT2 automated XY stages, CT6 cobot integration, and carousel stations — allow labs to boost throughput, reduce operator variability, and free up staff for higher-value activities. The systems are engineered to support a wide spectrum of materials (plastics, metals, films, composites, medical devices) and comply with international ASTM and ISO test standards while enhancing repeatability and workflow efficiency.
-
Product
Hydraulic Pulse Fatigue Testing System
PFT-500
-
Jinan Testing Equipment IE Corporation
PFT-500 hydraulic pulse fatigue testing machine is mainly applicableto large size parts such as bridges, trusses, automotive chassis, front and rear axels, locomotive frames, chassis and various concrete structures for static compression test and dynamic unidirectional pulse fatigue tests. The Fatigue Testing System for Rail has significant characteristics of reliable design, simple operation, energy conservation, and low operation cost etc.
