Controllers
direct and or manage action.
-
Product
Interface
RCNIC-A2PAU4
Interface
Abaco Systems' RCNIC-A2PAU4 is a high performance 4-lane PCI Express interface for monitoring, generating or analyzing full-bandwidth AFDX/ARINC 664 protocol traffic. Our exclusive pipeline architecture maximizes packet throughput using parallel controllers and efficient DMA transfers, thereby avoiding the bottlenecks of CPU-based interface solutions.
-
Product
Motion Control Board, PCI
APCI-8001
-
*Axis control for 3 servo or stepper motors*Onboard processor*Optical isolation*16-bit analog output channels*Direct connection of commercially available incremental encoders or SSI absolute encoders*Possibility of extension to a total of 8 axes*Menu-driven test application
-
Product
PCI Resistor Card 2-Channel 1.5 Ohm To 4.09k Ohm With SPDT
50-293-123
Programmable Resistor Modules
The 50-293 is a Programmable Resistor card with either two channels of 16-bit or four channels of 8-bit resistor chains in a single PCI card. The card is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Fanless Embedded System With I.MX 8M Processor, COM, LAN, USB, DIO (2-in/2-out), 2 PCIe Mini Card Slots, Optional CANBus, Power Design With ACC Ignition And E-Mark Certification For Vehicle Box PC
Agent336
-
The Agent336 is a RISC-based fanless embedded box PC certified with E-Mark for a variety of in-vehicle applications. The Agent336 measures only 164 x 118 x 44 mm and weight about 1.0kg. The cost-efficient embedded computer can withstand harsh operating environments with a wide operating temperature range of -40°C to +70°C and power input of 9 to 36V DC. This low power yet high-quality In-vehicle box computer is powered by the NXP i.MX 8M processor with the ARM® Cortex™-A53 microarchitecture and has a 3GB onboard LPDDR4 memory. Concerning the reliability and durability, the Agent336 comes with intelligent power management for ACC on/off delay, shutdown delay and over/under voltage protection. It runs on Linux (Yocto) and Android 8.1 operating systems. This IP40-rated RISC-based embedded gateway with strict certification is definitely the top choice for in-vehicle solutions, such as devices controller, fleet management, surveillance, and gateway. The newest RISC-based Agent336 supports two RS-232/422/485 ports, one isolated DIO, one HDMI port, two USB 3.0 A-type ports, one console port, one Gigabit LAN port, one RTC battery, one reset button, and five antenna openings. One onboard 8GB eMMC and one Micro SD card socket are available for extensive storage needs. Additionally, the rugged embedded computer has high integration ability with two full-size PCI Express Mini Card slots and one SIM card, which makes it a professional embedded system for transportation applications.
-
Product
1 / 2 / 3 MHz Multi-Waveform Signal Generator
MSG1M / MSG2M / MSG3M
-
- Wide frequency range- Sine, triangle, square, ramp, pulse, TTL (Sync) & DC outputs- Low distortion high resolution on low frequency output attenuation up to 80dB- Variable DC offset control- Four digit digital display with frequency indication in Hz, KHz, MHz/Amplitude display
-
Product
Simultaneous Wavelength Dispersive X-ray Fluorescence Spectrometer
Simultix 15
-
Multi-channel simultaneous wavelength dispersive X-ray fluorescence (WDXRF) spectrometer system, the Simultix 15 high-throughput WDXRF spectrometer. Analyze beryllium (Be) through uranium (U) in almost any sample matrix. The most important metrics for automated process control are precision, accuracy and sample throughput. With up to 30 (and optionally 40) discrete and optimized elemental channels and 4 kW (or optionally 3 kW) of X-ray tube power, Simultix 15 delivers unparalleled analytical speed and sensitivity.
-
Product
Ultrasound Detector
D240X
-
Very popular heterodyne and time expansion detector with backlit, large digit, accurate digital display, showing the tuned frequency in the heterodyne mode. The frequency and volume controls are on the side of the case, making it easy to adjust. Using stereo headphones, the heterodyne signal is heard on the left channel and the time expansion signal on the right channel. When the built-in speaker is used, a switch is used to select the heterodyne or time expansion signal.
-
Product
Panel Mount Calibrators
-
Practical Instrument Electronics, Inc.
Now you can panel mount PIE 820 & 830 Multifunction calibrators. As part of a calibration bench, the PIE 820PM or 830PM provide an accurate multifunction calibrator that is easy to use and may be removed for annual calibration. Panel mounting a multifunction calibrator is useful whether you are putting a calibration bench in your instrument shop, require a manual loading station in a control panel or for use as a built-in process simulator.
-
Product
Vision System With LGA1151 Socket 7th/6th Gen Intel® Core™ I7/i5/i3 & Celeron®, Intel® Q170, 4 PoE, 4 USB 3.0, And Real-time Vision I/O
IPS962-512-PoE
-
The IPC962-512-PoE meets the increasing requirements for maximum quality and flexibility in modern production plants. It features flexible expansion capacity, camera communication interfaces, real-time vision-specific I/O with microsecond-scale and LED lighting control. This machine vision controller is powered by the LGA1151 socket 7th/6th generation Intel® Core™ (codename: Kaby Lake/Skylake) and Celeron® processors (up to 65W) with the Intel® Q170 chipset. The IPS962-512-PoE comes with a full range of isolated I/O interfaces and real-time controls essential to machine vision applications, including trigger input, LED lighting controller, camera trigger, as well as an encoder input for conveyor tracking. The real-time vision system PS962-512-PoE enables a fast and high accurate inspection to ensure that the desired quality is achieved with no manufacturing defects. It supports four IEEE802.3at PoE LAN ports and four USB 3.0 ports for connection with industrial cameras. Operating over a wide temperature range from -10°C to +55°C, the IPS962-512-PoE provides reliable and stable performance within severe environments. Its easy setup and compact design are ideal for space constrained environments. Moreover, one PCIe x16 and one PCIe x4 expansion slots allow quick installation of I/O cards and graphics cards. Two easy-swappable 2.5" HDDs are available for extensive storage needs.
-
Product
Transmitters for Humidity Measurement
-
Our humidity and temperature measurement transmitters with either an interchangeable probe input, or a fixed / integrated probe provide high precision measurements with analogue or digital outputs for process monitoring and control.
-
Product
Vivarium Rooms
-
Darwin Chambers Company ALAAC, OLAW, USDA, and NIH-compliant Vivarium Rooms are designed for maximum value, sustainability, and conformance with applicable standards. We have over a decade of experience in working with researchers to provide humane and often precise conditions to meet their unique and specific needs. Vivariums are commonly defined as a place, such as a in laboratory, where live animals and/or plants are kept under conditions simulating a natural environment. Often, these contain both plants and animals, within a micro-ecosystem, often with controlled stability or controlled change of environmental variables. We offer various surface finishes, including all stainless steel, which are easy to maintain and may be sterilized to cleanroom standards. Compartmentalized enlosures are offered, which are modular and reconfigurable. Our rooms will accommodate plants as needed (we also provide plant growth chambers), and we offer control of humidification in conformance with current ALAAC mandates, sufficient air exchanges, available HEPA filtration of intake and/or exhaust air, standard screened equipment hous- ings, and other such considerations.
-
Product
PDS Singlebeam Survey & Processing/Charting
-
Teledyne PDS Singlebeam provides all necessary functionality to perform a survey accurately and quickly. This turnkey solution offers the surveyor and helmsman a strong tool to carry out the survey efficiently. Survey planning, data acquisition, data processing, editing, volume calculations, and chart production are all part of the software, making it easy to use.During data collection, the sailed part displays real time in top, profile, and 3D views using a color-coded digital terrain model (DTM). Quality control displays reassure the operators that the data is of the desired quality. The line base editing modules offers operators the right tools for data editing and cleaning.
-
Product
Digital Ior Leakage Current Clamp Tester
MCL-400IR+
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
・About Ior Leakage CurrentRecently, the leakage current clamp meter is widely used for insulation control of low voltage circuit as the supplementary method of the insulation resistance measurement. The control of leakage current has the advantages to enable the prediction of insulation condition in the electrical power line without having to shut off the power. The leakage current (Io) includes the capacitive leakage current (Ioc)originated in the capacitance and the resistive leakage current (Ior) originated in the insulation resistance each related to the ground. It is considered that the measurement of resistive leakage current (Ior) is the very useful and effective method for the insulation control of low voltage circuit. However, it was difficult to measure the resistive leakage current (Ior)with traditional leakage current clamp meter. MCL-400IR new digital clamp tester enabled the measurements of the resistive leakage current (Ior)without voltage input(phase detection).
-
Product
21 Slot, 3U PXIe Chassis
GX7200 Series
Chassis
The GX7200 Series mainframes are 21-slot PXI chassis that can accommodate up to 20 instruments as well as a PXI Express controller (an embedded CPU or a PXI bus expander interface such as the MXI). The backplane architecture supports Gen 2 PCI Express bus signaling and the use of both x1 or x4 system controllers. By offering a combination of PXI-1, Hybrid, and Express slots, the GX7200 offers users the ultimate in flexibility for general purpose as well as high bandwidth test needs.
-
Product
Oxygen/Nitrogen/Hydrogen Analyzer
EMGA-930
-
This is a simultaneous oxygen, nitrogen & hydrogen elemental analyzer with high accuracy and repeatability suiting to cutting-edge technology's R&D as well as quality control in the market of steel, new materials, catalyst and so on. This is a new generation model optimized to fit to user's requests.The oxygen is measured as carbon monoxide and carbon dioxide by two non-dispersive infrared detectors, the nitrogen by a thermal conductivity detector and the hydrogen with non dispersive Infra Red detector as H2O.
-
Product
Fluid Power Actuators
LP/LH
-
Rotork linear actuators offer the advantages of compact size, high performance and a simple but highly reliable design. They are ideal for operating on/off and control functions of both globe and wedge gate valves. Both spring-return and double-acting configurations are available with either pneumatic or hydraulic cylinders.
-
Product
Controllers
-
Sensors gather measured values in a vessel and forward them to the controller. Through an adjustment in the controller, the measured values can be adapted to the specific conditions at the measuring point.
-
Product
PCIe-6353 , PCI Express, 32 AI, (16-Bit, 1.25 MS/s), 4 AO (2.86 MS/s), 48 DIO Multifunction I/O Device
81049-01
Multifunction I/O
PCI Express, 32 AI, (16-Bit, 1.25 MS/s), 4 AO (2.86 MS/s), 48 DIO Multifunction I/O Device - The PCIe‑6353 offers analog I/O, digital I/O, and four 32‑bit counters/timers for PWM, encoder, frequency, event counting, and more. The device delivers high-performance functionality … leveraging the high-throughput PCI Express bus and multicore-optimized driver and application software. Onboard NI‑STC3 timing and synchronization technology delivers advanced timing functionality, including independent analog and digital timing engines and retriggerable measurement tasks. The PCIe‑6353 is well suited for a broad range of applications, from basic data logging to control and test automation. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
-
Product
Module for VME & VXI Systems
EXC-4000VME/xx / EXC-4000VXI/xx
-
The EXC-4000VME/xx and EXC-4000VXI/xx cards for VME & VXI systems supports up to eight dual redundant MIL-STD-1760 channels using the M4K1553Px(S)-1760 module and is compatible with all common variations of MIL-STD-1760 (A, B). Each channel can operate simultaneously as a Bus Controller and up to 32 Remote Terminals and as a Triggerable Monitor. In addition, Checksum, SRQ bit and Header Words are supported on each channel.
-
Product
Wire Crimp Testers
-
Imada offers manual and motorized wire crimp test systems in either vertical or horizontal configurations.Lever-operated systems offer basic functionality and rapid destructive testing up to 220 lbf.Motorized systems have speed control and are capable of destructive or force-controlled non-destructive testing up to 1100 lbf.Choose from manual or automatic wire-gripping fixtures.Digital gauges offer data output for analysis with data acquisition software.Create your own custom configuration or consult our application specialists.
-
Product
PXI Chassis, 19-Slot
40-923A-001
Chassis
The 40-923A includes all the features and performance required by the PXI standard and supports a control interface or embedded controller and up to 18 additional 3U peripheral modules.
-
Product
USB-6343, 32 AI (16-Bit, 500 kS/s), 4 AO (900 kS/s), 48 DIO USB Multifunction I/O Device
782253-01
Multifunction I/O
32 AI (16-Bit, 500 kS/s), 4 AO (900 kS/s), 48 DIO USB Multifunction I/O Device - The USB‑6343 offers analog I/O, digital I/O, and four 32‑bit counters/timers for PWM, encoder, frequency, event counting, and more. Onboard NI‑STC3 timing and synchronization technology delivers advanced timing functionality, including independent analog and digital timing engines and retriggerable measurement tasks. The USB‑6343 is well suited for a broad range of applications, from basic data logging to control and test automation. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
-
Product
Economic DSP-Based 8-Axis Motion Control Universal PCI Card
PCI-1285E
-
Encoder input is 10 MHz for 4xAB mode, 2.5 MHz for CW/CCW modePulse output up to 5 MppsMemory buffer for trajectory planning (circular trajectory and auto blending are not supported)Supports E-Gear (only for PCI-1245E)Hardware emergency inputWatchdog timerPosition latch via ORG & index signalProgrammable interruptRDY/LTC-dedicated input channels & SVON/CMP/CAM-DO/ERC-dedicated output channels are switchable for general input and output purposes
-
Product
DMX Tester
DMXter 2U
-
Here's the DMXter 2U, a Lil'DMXter2 for bolted down applications. All the hardware and software features of the standard Lil'DMXter2 in a 2U 19" rack box, plus many new features.The user controls, the XLR connectors, and the LED illuminated LCD display are on the front panel. The 2U is equally at home as the back up controller in a theatre or TV studio, running a trade show booth, the background lighting for themed entertainment or as the built in test controller in a touring show DMX distribution rack. Its increased I/O capabilities will make it a useful addition to your test bench.
-
Product
PXIe8862, 2.6 GHz 8-Core PXI Controller
790622-01
Embedded Controller
The PXIe8862 is an Intel Core i7 8Core embedded controller for PXI Express systems. You use the PXIe8862 for processor-intensive RF, modular instrumentation, and data acquisition applications. The PXIe8862 includes two 10/100/1000/2500BASET (Gigabit) Ethernet ports, two USB 3.0 ports, four USB 2.0 ports, as well as an integrated hard drive, serial port, two Thunderbolt 4 ports, and other peripheral I/O.
-
Product
Lock-in Amplifier
UHFLI
-
The Zurich Instruments UHFLI is a digital lock-in amplifier covering the frequency range from DC to 600 MHz. In addition of providing the highest operation frequency amongst all commercial lock-in amplifiers, the UHFLI also offers the lowest time constant of 30 ns for demodulation, resulting in a demodulation bandwidth of more than 5 MHz. The exquisite analog front end offers a spectacular noise performance of 4 nV/Hz which helps in many applications to keep the signal-to-noise ratios high while speeding up the measurement. In combination with the most innovative instrument control software LabOne, the UHFLI is the flagship of all Zurich Instruments products and represents the state of the art of today''s scientific instrumentation.
-
Product
PXI-6236, 4 AI (16-Bit, 250 kS/s), 4 AO, 6 DI, 4 DO, Bank-Isolated, PXI Multifunction I/O Module
779622-01
Multifunction I/O
4 AI (16-Bit, 250 kS/s), 4 AO, 6 DI, 4 DO, Bank-Isolated, PXI Multifunction I/O Module—The PXI‑6236 is a bank-isolated DAQ device designed for current I/O. It offers analog I/O, digital input, digital output, two 32‑bit counters, and digital triggering. The digital input and outputs are compatible with 5 V TTL/CMOS signals. It combines the safety and performance benefits of isolation with high-performance timing, amplification, and calibration technologies to offer accurate measurements and precise control. The PXI‑6236 is ideal for test, measurement, control, and design applications in environments with high voltages and electrical noise. You can use the PXI‑6236 to read from encoders, flow meters, and proximity sensors as well as control valves, pumps, and relays.
-
Product
Air, Soil, Liquid, And Gas
-
Omega's Environmental products include Water Quality Sensors, Transmitters and Controllers. Air Quality devices include indoor air quality Transmitters and Industrial Carbon Monoxide Transmitters.
-
Product
Connect Broadband Access Controller
CBAC
Controller
Evolve your fiber network with an open software solution that facilitates faster product innovation cycles, increased automation, and deeper network visibility.
-
Product
Bay Control
-
Schweitzer Engineering Laboratories, Inc.
Integrated bay control systems combine complete bay control with high-speed breaker protection, allowing you to deploy a full substation protection, control, and monitoring solution that is flexible for your application.
