Controllers
direct and or manage action.
-
product
PCI Direct Digital Synthesizers
SYNTH300-TRIG-HS
These devices provide two synchronized DDS-based RF channels on a single PCI card. With fine frequency and phase control, triggered operation, and the ability to accept an external clock, the Synth300 products enable a number of advanced applications at a fraction of the cost of conventional equipment. In addition to two analog outputs, the product can be ordered with one (or two) LVDS outputs for programmable digital clock applications, and can be configured for control by externally supplied TTL signals for low-latency triggered operation such as PSK, FSK, and triggered sweep operation.
-
product
Power Phase Converter Single phase 220VAC to 3 phase 380VAC Converter
SDT-40KW
Zhejiang Sandi Electric Co., Ltd
SANDI SDT series single-phase to three-phase converter, adopted SVPWM modulation control technology, which can convert ordinary single-phase power to industrial three-phase power. After through SDT series single-phase to three phase converter power conversion, the three-phase power output is standard pure sine wave, the harmonic distortion rate (THD) is less than 2%, totally meet the national standards of three-phase power quality, applicable to all types of load.
-
product
Scalar Mixer / Converter Measurements
S95082B
The S95082B scalar mixer / converter measurements software provides an intuitive and easy-to-use user interface for setting up mixer and converter measurements with single or dual conversion stages. It controls the analyzer’s built-in source(s) and external signal generators for use as LO signals.
-
product
Vibration Meters
Companies must comply with the Control of Vibration at Work Regulations 2005 – this requires them to minimise and monitor exposure to hand-arm vibration and make sure that it does not exceed set levels and cause Hand Arm Vibration Syndrome. The best way to do this is by using a hand-arm vibration meter.
-
product
C+L Band Broadband Light Source
S-103
ASE broadband source slot module of FOTS system can offer special function that is able to change optical output spectral feature variously, which is change optical output spectral feature variously, which is followed by user’s driving embedded pump LD freely. The output power of each pump LD is controlled separately by the program that is set up by user. In the case optimum ASE source output features such as wide broadband (> 80 nm @ -10 dBm/nm) and stable output power (< 0.02 dB) is needed, it is made up so that the provided Default mode along with User mode can be chosen and set up. More stable application of ASE source is possible through the combination of monitoring of ASE output power, alarm status and pump LD status with real-time optimal feedback. The embedded FPGA processor makes high speed control possible and enables monitoring and feedback routine operated stably.
-
product
Rotational Rheometer
ARES-G2
The ARES-G2 is the most advanced rotational rheometer for research and material development. It remains the only commercially available rheometer with a dedicated actuator for deformation control, Torque Rebalance Transducer (TRT), and Force Rebalance Transducer (FRT) for independent shear stress and normal stress measurements. It is recognized by the rheological community as the industry standard to which all other rheometer measurements are compared for accuracy.
-
product
Differential Scanning Calorimeters
Differential Scanning Calorimeters (DSC) measure temperatures and heat flows associated with thermal transitions in a material. Common usage includes investigation, selection, comparison and end-use performance evaluation of materials in research, quality control and production applications. Properties measured by TA Instruments’ DSC techniques include glass transitions, “cold” crystallization, phase changes, melting, crystallization, product stability, cure / cure kinetics, and oxidative stability.
-
product
Assembly & Test Services
Once piece parts have been manufactured, skilled operators can kit or assemble them to the desired level. Our wiring technicians are trained to IPC standards of workmanship and operate within ESD controlled areas. We carry out both solder and crimp wire terminations along with integration of electronic components such as fans, PCBs and power supplies.
-
product
Digital IO
PA32IX
The PA32IX represents a new level of performance and capabilities for PXI-based digital instrumentation. Each card can function as a stand-alone digital subsystem or if required, multiple cards can be interconnected, supporting up to 512 bi-directional pins (16 boards). The PA32IX also supports deep pattern memory by offering 64 M of on-board vector memory with static per pin direction control and with test rates up to 50 MHz.
-
product
Universal Military Craft Systems Controller
3U VPX
The system is 3U VPX based. It consists of two CPU modules, a power supply module [SMART.PSU] Technology explained <- Click here, two PMC/XMC carrier modules and two MILBUS modules. Optional: WLAN module for controlling the system externally without hanger access (Aircraft on runway - pre-takeoff)
-
product
Panel Mount Calibrators
Practical Instrument Electronics, Inc.
Now you can panel mount PIE 820 & 830 Multifunction calibrators. As part of a calibration bench, the PIE 820PM or 830PM provide an accurate multifunction calibrator that is easy to use and may be removed for annual calibration. Panel mounting a multifunction calibrator is useful whether you are putting a calibration bench in your instrument shop, require a manual loading station in a control panel or for use as a built-in process simulator.
-
product
48-Ch SPDT 1A-100VAC 24VDC Switching
YAV91074
The YAV90074 module contents 48 SPDT Relays independent. Each relays PCB contact track is shielded individually in order to handle very low voltage signals and audio signals with extremely low crosstalk. The build-in power supply includes two extra filters to reduce the DC voltage ripple to the relay coils; the control tracks have been drawn in quadrature with signal ones, reducing the inductive coupling produced by the transient current.
-
product
Low Noise Differential Preamplifiers
Provide a high gain amplification to 1MHz with an AC output derived from a very low noise FET instrumentation amplifier. Each model has fixed gain settings of x1 (0dB), x10 (20dB), x100 (40dB) and x1000 (60dB) over a selectable bandwidths of 100Hz, 1kHz (HP), 3kHz, 30kHz, 100kHz and 1MHz (7000 model only). Noise referred to input is 7nV√Hz and common mode rejection is >100dB at 1kHz. Momentary pushbutton switches are provided that control coupling, bandwidth, gain and channel on/off selections. BNC connectors are provided for single-ended and differential input, ac output, and dc output (optional) connections.
-
product
Automated Shock Test Systems
AutoShock-II Test System
The AutoShock-II is a fully automated series of shock test systems used to measure and identify product fragility levels and evaluate protective packaging. With the simulation of real world shock pulses and impact energy levels, manufacturers can systematically test and optimize product design and packaging. L.A.B. Equipment, Inc.''s fully automated computer controlled shock and data analysis test systems are the critical path in accomplishing this optimization.
-
product
Magnetic Level Gauge Switches
ABB's magnetic level gauge switches for point level alarm and/or control can mount to a KM26 magnetic level gauge or an LS Series cage level switch.These switches are completely isolated from the process fluid as they are magnetically activated by a magnet equipped float (KM26) or attraction sleeve (LS Series). The unique magnetic coupling action eliminates seals, diaphragms, springs, and torque tubes common to other level switching alternatives since there is no physical contact with the process fluid. The magnetic coupling also eliminates process connections to the switch; therefore, no isolation valves are required to block off the switch for maintenance. The switch "set point" is easily adjustable without changing any process piping and the result is a more reliable and easier way to maintain level system.
-
product
PXI/PXIe Fault Insertion Switch, 32-Chan 2A, N/C Through Relays, Fault Buses on M & U
42-190C-212
The 40-190C-212 (PXI) and 42-190C-212 (PXIe) are fault insertion switches with 32 channels. They are part of a range of modules available with 74, 64 or 32 channels and are primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers.
-
product
Analog
Create complete systems while streamlining your development process and reducing your design risk. We design our mixed-signal, linear, interface and power products for seamless integration with our extensive portfolio of microcontrollers, digital signal controllers, microprocessors and FPGAs. Well-known for our thorough documentation, we provide parts that work on the bench the same way they’re described on paper. We also provide evaluation boards to demonstrate functionality, an intuitive Integrated Development Environment (IDE), simulation software and other design resources to create a rapid design, prototype and test environment for all aspects of your system design.
-
product
Remote I/O
Schweitzer Engineering Laboratories, Inc.
Remote I/O modules transfer data from remote locations over fiber and expand the I/O of SEL relays, automation controllers, and other devices without modification to the control panel face.
-
product
Front End Processor
SoftFEP
Process telemetry and command data streams in satellite control centersConnect satellite control centers with networked antenna sites.Fully software-defined and customer-configurable.
-
product
Rheometers
The MCR rheometer series from the market leader offers you one thing first and foremost: an open range of possibilities. Whatever your rheological requirements are and will be in the future – based on its modular setup, your MCR rheometer is efficiently and comfortably adapted and extended to meet your needs, from routine quality control to high-end R&D applications. An investment in an MCR rheometer is always a safe investment in longstanding technology: The air-bearing-supported EC motor, for example, was developed by Anton Paar and has been used in all MCR models for over 25 years to ensure accuracy across a vast viscosity range. It makes it possible to measure liquids with a viscosity even lower than water and also characterize stiff materials like polymer composites or steel by DMA – and everything in-between.
-
product
Combustion Flue Gas Analyzers
Combustion analysis in high definition is more than just a brilliant display. It's a combination of proven measurement standards, contractor-rugged design, and Testo's innovation. The result - Testo's series of combustion analyzer - makes combustion analysis easier to perform, easier to control, and easier to understand.
-
product
WAVEFORM GENERATOR
WFG 600
The multichannel, high voltage, computer controlled Waveform Generator WFG600 is an exceptional instrument designed primarily for experiments on addressing liquid crystal devices and is most suitable for all applications where synchronized trains of pulses with variable width and amplitude are required.
-
product
PXIe-8842 2.6 GHz 6-Core Processor PXI Controller
790657-33
The PXIe8842 is an embedded controller for PXI systems that you can use for processor-intensive modular instrumentation and data acquisition applications. The PXIe8842 includes two 10/100/1000/2500BASET (Gigabit) Ethernet ports, one Thunderbolt 4 port, two USB 3.0 ports, four USB 2.0 ports, as well as an integrated hard drive, serial port, and other peripheral I/O. Thunderbolt is a trademark of Intel Corporation or its subsidiaries in the US and/or other countries.
-
product
Analog Output Module, 16-bit
IP235A
IP235A modules have a 16-bit D/A converter (DAC) to provide highly-accurate analog voltage outputs. An internal RAM buffer enhances control over the transfer of data to the DAC.
-
product
Bench Power Supply, Single, Adjustable, 1 Output, 0 V, 40 V, 0 A, 5 A
72-7295
The 72-7295 is a 40VDC Laboratory Grade Switching DC Power Supply with precision coarse and fine output voltage and current limiting controls. The output Overvoltage protection protects voltage sensitive load by instantly shutting down the supply when the output voltage goes beyond the set voltage due o line surge or otherwise. Current limiting control with automatic cross over of constant voltage and constant current modes makes this unit ideal for R&D work in laboratory situations.
-
product
FMC Expansion I/O Module.
SI-MOD32xx
The SI-MOD32xx is a family of high resolution, FMC form factor, high channel count multi function data acquisition and control modules that plug into any SI-DSP or FPGA carrier card.
-
product
Laboratory Ozone Test Chamber
CX-150
Shenzhen Chuangxin Instruments Co., Ltd.
Laboratory Ozone Test chamber is widely used to control products quality in measuring quality control; Rubber & Plastics; automobile production; wire and cable; packing materials; instruments and meters; medical equipment; civilian nuclear energy; civil aviation; colleges and universities; research laboratories; inspection arbitration, and technical supervision departments and other rubber products.
-
product
Bench DC Power Supply, Linear Regulation - Single, Dual Or Triple Outputs, Analogue Control, 30 To 130 Watts, Silent Cooling
EL-R Series
Single outputs, 30V/1A, 18V/3.3A, 56V/1.1A, 15V/5A, 30V/3ASingle, dual or triple outputs, 30V/2AIndependent digital voltage and current meters for each output with 4 digit resolutionSwitchable local or remote sensingConstant voltage or constant current operationVariable 1.5 - 5.0V auxiliary output at 2A (EL302RT)Compact design uses less bench spaceSilent fan-free coolingDC output switches, automatic mode indicationRS232 or USB controlled models available (30V/2A single)
-
product
Resistance Temperature Sensors
Watlow Electric Manufacturing Company
These sensors are suited for applications where accuracy and stability are essential for proper control in applications that operate at or below 1200°F (650C).
-
product
Rubidium Oscillator
Rubidium oscillators are a type of atomic clock and are the most accurate time standards known and are used as time distribution services to control things such as telecommunications infrastructure, TV broadcasts and global navigation satellite systems (GPS).
