VXI Backplanes
A VXI compliant electronic circuit board containing circuitry and sockets into which additional electronic devices or other circuit boards or cards can be plugged. (www.dothill.com)
See Also: VXI Chassis
-
-
Product
3U OpenVPX 2-Slot Backplane With 1 VPX Power And Ground Plus 1 VITA 62 Power Supply Slot
101VPX302-xxxx
-
This 3U Open VPX backplane offers one VITA 46 Power and Ground slot and one VITA 62 power supply slot to support the development and deployment of systems requiring a VITA 62 power supply. The rear power studs can be used to connect to an adjacent backplane to feed it power.
-
Product
VXI 12-Channel, 3-Wire LVDT/RVDT Simulation
65DL2
-
NAI’s 65DL2 is a 12-channel, 3-wire, LVDT/RVDT Simulation Instrument on a VXI board. This single-slot, message-based board features up to 12 stimulus channels of 3-wire LVDT/RVDT, wraparound self-test, and onboard programmable excitation supply. The board is uniquely versatile, as each excitation input and output voltage is programmable. In addition, each channel can be programmed to be controlled by an external DC voltage. A replacement for the 5410C-83, the 65DL2 is ideally suited for defense, commercial aerospace, and industrial applications.
-
Product
Multi-channel USB and Power Distribution Backplane
USBDR-8
-
Power worldwide with universal AC adapterDC power from 12V to 50V sourceInstall from 1 up to 8 channels per USBDR-8Daisy chain USBDR-8 to control up to 112 channels using just one USB portUSB 2.0 compatible communication Synchronize all USBPxx-S1 operation in tracking or dynamic control applications Operate on table top, wall mount, rack mount or DIN rail mount Optional DIN rail connection kit for mounting the USBDR-8 to DIN rail available Optional 19" aluminum rack mount plate available
-
Product
VXI Mainframes & Controllers
-
The Keysight VXI mainframes provide rugged enclosures with innovative air distribution systems for extremely quiet and efficient cooling. With power supply capacities up to 1000 watts, you can easily configure the system that truly meets your needs.
-
Product
VME / VME64x Backplanes
-
All Elma Electronic VME backplanes are designed to maximize performance, minimize noise, and to give the customer the most reliable, cost-effective product possible. The Elma Electronic VME64x backplane series is designed to fully comply with the ANSI/VITA VME extension standard.
-
Product
3U – 6U SOSA™ Aligned VPX Backplanes
-
Using a modular concept based on open standards it is common practice in the civil sector to integrate subsystems components from different manufacturers into a single modular system. The SOSA™ Technical Standard aims at such an interoperability in embedded computing for military applications.
-
Product
AdvancedTCA Backplanes
-
Mesh, Dual Star (5U), and 7U Pluggable Dual Star. Versions for both 19" rackmount and 23" ETSI racks are available. All Elma Electronic AdvancedTCA backplanes are compliant to the PICMG 3.0 Rev. 1.0 specifications.
-
Product
ITA, 9050, 50 Module, VXI and Discrete Wiring, Double Tier
410104538
-
The 50 module ITA can be used in a number of applications to accomplish the required connection to the Unit Under Test (UUT). You can mount a VPC front or rear mount enclosure or customize your own fixture to be attached on the frame. A wide range of ITA modules are available separately for user configuration.
-
Product
VXI Synchro/Resolver Simulation & Measurement
65CS4
-
NAI’s 65CS4 is a Synchro/Resolver Simulation & Measurement Instrument on a single-slot VXI board. The board incorporates up to four Synchro/Resolver measurement channels and up to four instrument-grade Synchro/Resolver simulation channels, or up to eight embedded grade Synchro/Resolver simulation channels that can be used independently and/or simultaneously.
-
Product
3U VPX 1 Slot P&G backplane with aperture for VITA 66.4
101V301P06-9X13
-
Power for 3.3V, 5V and 12V per VITA 46, with all rear connectors fully loaded. Use with Elma’s slot-to-slot or slot-to-I/O bulkhead cable products for system development.
-
Product
5-Slot 64-Bit 6U CompactPCI H.110 Bus Backplane
cBP-6405R
-
- PICMG:2.0 R3.0, 2.1 R2.0, 2.5 R1.0- Dimension (mm, WxH):120.9 x 262.05 (mm, WxH, vertical insertion view)- Segment:One- cPCI Bus:Up to 64-bit/66MHz- System Slot:Right-hand side (upper side for board's horizontal insertion)
-
Product
20-slot ATX-supported Bridged PICMG Bus Active Backplane
ATX6022/20GP18
-
*1 PICMG, 18 PCI and 1 ISA*Compatible with AX61492 chassis*Supports both AT and ATX power supply
-
Product
MIL-STD-1553 & ARINC PMC Interface Card. Supports cPCI/PXI Backplanes
CPCIC3/6-MA4
-
Alta Data Technologies’ CPCIC3/6-MA4 (PXI Compatible) interface module is a multi-channel, multi-protocol 1553 and ARINC PMC on 3U (PXI Compatible) or 6U carrier card supported by the latest software technologies. This hardware and software package provides increased system performance and reduces integration time.
-
Product
11-slot ATX-supported PICMG 1.3 Bus Passive Backplane
FAB121
-
*Designed for PICMG 1.3 SBC*Compatible with AX61410, AX6145, AX6156 chassis*Supports one PICMG 1.3 CPU card slot, seven PCIe x4 slots, one PCIe x8 slot, and two 32bit/33MHz PCI slots
-
Product
5-slot ATX-supported PICMG 1.3 Bus Passive Backplane
FAB105
-
The FAB105 features a PICMG 1.3 CPU card slot, one PCI Express x16 slot, three 32bit/33MHz PCI slots, and built in a 24-pin ATX power connector and 8-pin connector for thermal detected board. The FAB105 is perfect fit for AXIOMTEK's SHB100 and SHB110, which are built around the PICMG 1.3 form factor. The FAB105 is compatible with the AX60501 chassis.
-
Product
cPCI Serial Backplanes
-
CompactPCI Serial is an industrial standard for modular computer systems. It is based on the established PICMG 2.0 CompactPCI standard, which uses the parallel PCI bus for communication among a system's card components. In contrast to this, CompactPCI Serial uses only serial point-to-point connections.
-
Product
Backplane
P47
-
VECTOR Electronics and Technology, Inc.
Power supply backplane provide a modular approach for the addition of plug-in, hot-swap power supplies. As a result there is no need to modify expensive backplanes to incorporate redundant power supplies or N+1 configurations. Multiple power supply backplanes may be bridged together for additional power supply requirements.
-
Product
VXI Analog Instruments
Ai-762
-
Ai-762—the newest member of the Ai-760 Series in the Core Systems Instruments (CSi) family—is a standards-based integrated test and measurement tool that consolidates traditional instruments into a single-slot VXI package.
-
Product
1 PICMG® CPU, 1 PCI-E® x16,1 PCI-X™, 2 PCI™ Slots Backplane
EBP-5E1
-
- Segment: 1- Slots:1 PICMG® CPU, 1 PCI-E® x16, 1 PCI-X™, 2 PCI™- Support ATX power supplies- Dimension: 153 mm x 330 mm
-
Product
PCIe 6.0 Protocol Test Backplane
P5563B
-
The Keysight P5563B PCIe 6.0 Protocol Test Backplane provides a convenient means for testing PCIe 6.0 add-in cards with a self-contained portable and powered passive backplane. The P5563B provides power required for all combination of exerciser and analyzer with device under test.
-
Product
Digital Backplane Interface Board
MSXB 033
-
The Microstar Laboratories Digital Backplane Interface Board, part number MSXB 033, interfaces the Digital Backplane with a Data Acquisition Processor. The Digital Backplane Interface Board must be installed in the Digital Backplane to connect the backplane to a Data Acquisition Processor.
-
Product
5-slot ATX-supported PICMG 1.3 Bus Half-size Backplane
HAB206
-
The HAB206 has a PICMG 1.3 CPU card slot, a PCIe x 16 slot and a total of three 32bit/33MHz PCI slots. The onboard 24-pin ATX power connector and 8-pin connector for thermal detected board are featured. Furthermore, the backplane supports two onboard SATA ports (optional function). The HAB206 is perfect fit for AXIOMTEK's half-size CPU cards, the SHB210 and SHB211, which are built around the PICMG 1.3 form factor. We have an enclosure, the AX60501 and AX60530, to house the backplane.
-
Product
5U 6 slot ATCA backplane
109ATCA506-3013R
-
The 5U 6 slot ATCA backplane is a 6 slot replicated Mesh with radial IPMB, designed to meet 40Gbps (4 x 10G ports) data rates. Elma Bustronic’s ATCA backplanes have been simulated and characterized by our signal integrity lab to optimize performance.
-
Product
VXI 16-Channel, 2-Wire LVDT/RVDT Simulation
65DL1
-
NAI’s 65DL1 is a 16-channel, 2-wire, LVDT/RVDT Simulation Instrument on a VXI board. This single-slot, message-based board provides 16 independent, transformer-isolated, LVDT/RVDT, programmable 2-wire outputs (up to 34 V), wrap-around self-test, and an onboard programmable excitation supply.
-
Product
Analog Backplanes
MSXB 030
-
Analog Backplanes provide expansion slots to accommodate compatible analog external boards. Analog Backplanes are passive, and connect all signals in each of the expansion slots in parallel. All expansion slots are identical
-
Product
1-Slot Power & Ground only 7U VPX backplane with aperture for VITA 67 in J3
1900002558-9001R
-
Power for 3.3V, 5V and 12V, rear connectors fully loaded. Use with Elma’s slot-to-slot or slot-to-I/O bulkhead cable products for system development.
-
Product
5-slot ATX-supported PICMG 1.3 Bus Passive Backplane
FAB110
-
The FAB110 offers one PCIe x16 slot, one PCIe x4 slots and two 32bit/33MHz PCI slots as well as the PICMG 1.3 slot for the SHB (system host board). The onboard 24-pi ATX power connector and 8-pin connector for thermal detected board are featured. Furthermore, the backplane supports two high speed USB 2.0 ports. The FAB110 is designed for the 6-slot industrial chassis, such as Axiomtek's AX60501 and AX6052.
-
Product
OpenVPX Backplanes - 3U, 6U
-
OpenVPX provides a versatile, high-speed architecture utilizing the rugged Eurocard form factor. There are backwards-compatibility options with VME/64x with hybrid backplanes.
-
Product
ITA, 9050, 50 Module, VXI And Discrete Wiring, VDATS
410104721
-
Customized VDATS 9050 VXI ITA frame with 3 bearings per side.
