Smoke
-
Product
Smoke Detection Sensor - UL Approved
ENVIROMUX-SDS
-
For warning of smoke. Photoelectric smoke detector. Smoke sensitivity: 0.98-2.4%/ft. Built-in 135° F (57° C) thermal heat sensor. Includes mounting hardware. Connect to RJ45 or digital input sensor ports. Supports CAT5/5e/6 UTP or STP cables. Screw terminal. To connect to the RJ45 inputs use CAT5/5e/6 cable terminated at one end with RJ45 connector. Connect the un-terminated end to the sensor screw terminal. Operating temperature: 14 to 122°F (-10 to 50°C). Maximum cable length: 1,000 ft (305 m). Powered by ENVIROMUX-2D/5D/16D. Regulatory approvals: UL, RoHS.
-
Product
Diesel-engine Vehicle Smoke Meters
-
Foshan Analytical Instrument Co, Ltd.
Digital display, clear and direct-visual.Small in size and light in weight. Easy operation and quick in measurement.It meets the technical requirement of the National standard GB3847-2005.It is suitable for the measurement of exhaust smoke,under the state of free acceleration,from the diesel-engine vehicles.
-
Product
Chassis Dynamometer Smoke Testers
-
A chassis dynamometer smoke tester (CDST) is used to test diesel emissions when the engine is under load. This is of course a much more realistic test than the commonly used free acceleration test. It is also better for the diesel engine.During a CDST test an automatic test cycle is performed, whereby the emission is measured at different engine loads. The monitor shows checks and actions to perform before the test, shows real-time measuring data and instructions for the driver during the test, and the end results after the test.
-
Product
TURBO AIR SYSTEM TEST KIT WITH SMOKE ADAPTER
TPT69700A
-
*Helps locate air leaks in turbo system components by plugging the output side of the turbo and the intake inlet*Air is applied through one adapter to show the presence of leaks within the system*Six pairs of stepped adapters to fit most turbo systems on cars and light trucks
-
Product
VLT Chassis Dynamometers for Diesel Smoke Testing under Road Conditions (CDST)
-
Diesel Smoke Testing by Free Acceleration Test is one! But how accurate is this Test? We all know that it is a not valuable test, but still better as none testing of Vehicle Diesel Engines. The results are not realistic in many cases. And not as good for the Engine we know.
-
Product
Smoke Detector Testing
-
Requirements for testing of smoke detectors vary by country, the common need is for a functional test where smoke, or simulated smoke, is introduced through the vents of the detector to the sensor.
-
Product
Fuse Saver Master Kit
#8016
-
Innovative Products of America
The Fuse Saver provides a fast and safe solution to the old methods of "smoke testing" a short. This all inclusive kit includes a durable custom blow molded case. With the Fuse Saver you can move about your vehicle while checking for shorts in the electrical system.
-
Product
Multispectral PTZ Thermal Camera
Saros DM-Series
-
The FLIR Saros DM-Series introduces eight new VGA and QVGA resolution options to FLIR’s multi-sensor security lineup. Capable of capturing video in complete darkness, bright sunlight, and through smoke, dust, or light fog, the DM-Series provides superior perimeter protection in the toughest lighting and environmental conditions. A built-in 4K visible light camera operates alongside the thermal sensor to capture minute details in low light conditions. The DM-Series also integrates with the FLIR United Video Management System (UVMS), as well as other ONVIF-compliant video management systems. This gives users complete control over the all new dual-sensor viewing mode, alarm functions, and fully programmable preset tour.
-
Product
Opacimeter on CONNECT Trolley for Measurement of Diesel Vehicles
MO CT | VP 135045
-
Maschinenbau Haldenwang GmbH & Co. KG.
The MAHA Opacimeter on CONNECT trolley is used for the measurement of diesel vehicles. The smoke opacity is tested and diagnosed in a time-saving and trouble-free manner in a partial flow procedure during free acceleration or under load of the engine. Rapid readiness for measurement and precise measurement results are the distinguishing features of the MAHA Opacimeter. Type-tested according to PTB requirements 18.09.
-
Product
Diesel Smoke Analyser
VLT-E9200
-
The VLT-E9200 diesel smoke analyser measures the opacity of the exhaust gases of vehicles with diesel engines. It can measure if an engine comkplies with the EURO 6 standards. An oil temperature sensor and an rpm counter can be connected.
-
Product
SparkFun Photodetector Breakout
MAX30101 (Qwiic)
-
The SparkFun Photodetector Breakout is an updated version of the SparkFun Particle Sensor Breakout includes the MAX30101, a highly sensitive optical sensor and successor to the MAX30105 and MAX30102. The MAX30101 Breakout utilizes a photon detector to measure the amount of returning light that is reflected back from the LEDs. This is useful for various applications like particle (i.e. smoke) detection, proximity measurements, and even photoplethysmography. To make it even easier to use this breakout, all communication is enacted exclusively via I2C, utilizing our handy Qwiic system. However, we still have broken out 0.1" spaced pins in case you prefer to use a breadboard.
-
Product
Emission Measurement Technology
-
Maschinenbau Haldenwang GmbH & Co. KG.
When measuring exhaust gas, the CO concentration or - in diesel vehicles - the smoke gas opacity is measured. In this way it can be determined whether the exhaust system meets the legal requirements and is in perfect condition.
-
Product
Air Quality Measurement
-
Air pollution measurement is the process of collecting and measuring the components of air pollution, notably gases and particulates. The earliest devices used to measure pollution include rain gauges, Ringelmann charts for measuring smoke, and simple soot and dust collectors known as deposit gauges.
-
Product
Smoke Detection Sensor - CE Approved
ENVIROMUX-SDS-CE
-
For warning of smoke. Photoelectric smoke detector. Smoke sensitivity: 0.08-0.14 dB/m. Built-in 135° F (57° C) thermal heat sensor. Includes mounting hardware. Connect to RJ45 or digital input sensor ports. Supports CAT5/5e/6 UTP or STP cables. Screw terminal. To connect to the RJ45 inputs use CAT5/5e/6 cable terminated at one end with RJ45 connector. Connect the un-terminated end to the sensor screw terminal. Operating temperature: 14 to 122°F (-10 to 50°C). Maximum cable length: 1,000 ft (305 m). Powered by ENVIROMUX-2D/5D/16D. Regulatory approvals: CE, RoHS.
-
Product
Particle Counter
-
TES Electrical Electronic Corp.
Monitoring air pollutant souce from dust, pertochemical industry, steel-making plant, thermal power plant, restaurant, smoke, burning plnats, driving automobiles.The meter is a real time air quality monitor instrument used to monitor the concentration of PM2.5 humidity and temperature in the indoor environment.
-
Product
Digital Dust Monitor
3443
-
The Kanomax Digital Dust Monitor – Model 3443 measures aerosol concentrations corresponding to PM10. The intake isolates the aerosol sample so that the optics chamber is kept sterile for improved reliability and low maintenance. The unit measures 0.1 to 10µm particle size aerosol contaminants such as fumes, dust, smoke and mists. It is battery-operated, data-logging, light-scattering laser photometer that gives you real time aerosol mass readings. It is also suitable for clean office settings well as harsh industrial workplaces, construction and environmental sites, and outdoor applications.
-
Product
UNIVERSAL FILLER NECK CONNECTOR
SMOKE30
-
*Creates an air-tight seal with any vehicles EVAP system, eliminating the need for searching for the EVAP service port*Capless fuel system adapter works with your smoke machine to test EasyFuel™
-
Product
EVS for Experimental and Homebuilt Aircraft
-
Give your aircraft a safety boost with a Max-Viz enhanced vision system (EVS) from Astronics. These systems help you see through smoke, fog, and night to help you avoid runway obstructions, severe weather, and more.
-
Product
Thermal Imaging Camera
IRT301
-
Wuhan JOHO Technology Co., Ltd
IRT301 Thermal Imaging CameraIRT301, a fixed-site thermal security camera lets you aware of intruders and other threats to your facility clearly in total darkness, smoke, mist and other harsh situation. It is compatible with a wide variety of third-party accessories, permit them easy to integrate. It enable to control and operation over digital and analog networks. With 384x288 pixel detector, it delivers high quality thermal image in any harsh environmental conditions, IRT301 is ideal for both indoor and outdoor surveillance, applications covered from industrial monitoring to city or boundary security monitoring. ApplicationBorder security and surveillanceRoad, channel, warehouse monitoringBuilding and industrial safety monitoringKey FeaturesRugged, waterproof and dustproof designHigh resolution, high frame rateAdvanced image processing technologyStandard interfaceVarious lenses and pan-tilt optionsTechnical specificationDetectorDetector MaterialUFPA microbolometer, AsiResolution384x288, 25mSpectral range8m~14mNETD80mK@30LensFocus
-
Product
Zero Emission Cabinets
-
A zero emission cabinet is connected to the exhaust extration system of the building and prevents exhaust gases from escaping into the building.VLT offers several different zero-emission cabinets for use with emission and diesel smoke analysers. They can be connected to your exhaust extraction system. Mandatory in some countries.
-
Product
Opacimeter for the Measurement of Diesel Vehicles
MO / MAHA OPAZIMETER | VP 135043
-
Maschinenbau Haldenwang GmbH & Co. KG.
The MAHA Opacimeter is used for the measurement of diesel vehicles. The smoke opacity is tested and diagnosed in a time-saving and trouble-free manner in a partial flow procedure during free acceleration or under load of the engine. Rapid readiness for measurement and precise measurement results are the distinguishing features of the MAHA Opacimeter. Type-tested according to PTB requirements 18.09.
-
Product
Air Amplifiers
-
Nex Flow® Air amplifiers are compact, low cost air flow “movers” that are virtually maintenance free. Applications include the venting of fumes and smoke, conveying of low weight materials, and entraining a high volume of air to cool, blow off, and dry. Air Amplfiiers use the “Coanda effect” to draw in the surrounding atmosphereic air while consuming only aminimal amount of compressed air. These products can amplify airflow up to 17 times (depending on the size) resulting in dramatcally reduced levels of noise. Air Amplifiers (also called Air Movers) draw in atmospheric air from the back of the unit as well as having downstream entrainment further amplifying the flow. They are used for cooling and venting. While the force produced for blow off decreases as the amplifier outlet diameter increases, these Air Movers are ideal for cooling because of the high velocity outlet fow and and are much more effective for cooling compaed to air nozzles.
-
Product
IP Surveillance Camera
ENVIROMUX-IPCAM
-
View and control the camera from the ENVIROMUX web interface, the camera web interface, included software, or with a compatible cell phone. With the ENVIROMUX-2D/5D/16D, a triggered snapshot can be forwarded in alert e-mails. A snapshot can be triggered by any programmed event (motion detection, door open/close, glass break, smoke, liquid detection, etc.). Image sensor: 1/4" progressive scan CMOS sensor. Video Streaming: simultaneous Motion JPEG and MPEG-4. Frame rate: 30fps at 640x480 (VGA) resolution. Lens: F2.0, 4.0 mm (0.16 in). RJ45 connector. Wireless models: wireless IEEE 802.11 b/g up to 54 Mbps. Regulatory approvals: CE, FCC, RoHS.
-
Product
Carbon Monoxide Detector Tester
Solo C3
-
Many multi-sensor fire detectors detect carbon monoxide (CO) as well as smoke and / or heat. Under international codes and standards the CO cell needs to be functionally tested with a CO stimulus from the protected area through the detector vents to the sensor.
-
Product
Dust and Opacity Compliance Monitors
-
LAND has a range of opacity, dust, smoke and particulates monitors which are the most advanced available, using patented measurement technology to give high accuracy. The analysers (which comprise a transmitter and a reflector) are mounted across the stack, the optical measurement technique uses no moving parts, giving the highest possible reliability with very low maintenance.
-
Product
AID Box Camera
TrafiBot HD
-
FLIR TrafiBot HD combines field-proven video detection algorithms with advanced camera optics and powerful processing technology in a single box camera. TrafiBot HD (with 1920 × 1080 resolution) provides superior image quality, embedded AID analytics, as well as multi-stream encoding. TrafiBot HD’s advanced processing unit generates traffic data and incident detection information and thus supports traffic operators with alerts on stopped vehicles, wrong-way drivers, pedestrians, lost cargo, smoke, and traffic flow data.
-
Product
Flow Monitor
Deltaflow 180
-
The DeltaFlow® 180, measures volumetric flow from smoke stacks or pipes for process and compliance applications; it is a complete flow monitoring solution with easy installation in all applications including those with elevated temperature, particulate loading and corrosive gas concentration.
-
Product
Smoke Density Tester
TF350
-
TESTEX Testing Equipment Systems Ltd.
Smoke Density Tester , is widely used for density determination of smoke from the burning or decomposition of plastics and building material, designed according to ASTM D2843 and GB/T 8627. Equipped with high accuracy PLC and colorful touch panel.
-
Product
Ultrasonic Sensors
-
Ultrasonic sensors present the ideal solution for non-contact position and distance measurement in all industrial areas where environmental conditions such as dust, smoke or steam may affect the sensors. Objects consisting of a variety of materials can be detected to within millimeters regardless of color or shape.
-
Product
CO Detector Testing
-
Many multi-sensor fire detectors detect carbon monoxide (CO) as well as smoke and / or heat. Under international codes and standards the CO cell needs to be functionally tested with a CO stimulus from the protected area through the detector vents to the sensor.
