Impulse
-
Product
Impulse Sledge Hammer
-
Impact hammers are designed to measure the frequency of mechanical structures, such as mechanical movement, mechanical damping and impedance.
-
Product
Lightning Impulse Simulation Tester
KT-6030iG
-
Most of all electric systems and equipments are weak against the lightings(direct, inductive lightning). In fact, those electric equipments are broken mainly by lightning.This Lightning Impulse Simulation Tester is certificated to IEC 61000-4-5, and generates the similar impulse with huge rush currents and tests the safety of the power systems and equipments.
-
Product
Impulse Spark Tester
IT-25B
-
While most military standards now favor high frequency spark testing over impulse spark testing, the IT-25B Impulse Spark Tester is available for use in some aeronautic applications that still specify the impulse method. The IT-25B meets the test requirements of military specifications MIL-C-13777E, MIL-W-16878, and NEMA standards for hook-up wire used in high temperature wire applications. This method is favored as an alternate to a wet dielectric test.
-
Product
Impulse Current Measuring Shunts
ICMS
-
The Impulse Current Measuring Shunts ICMS are new designed tubular shunt types with best response behavior to match the high performance of the TR-AS digital recorder for comparative current measurements. A 1st partial response time less than 10ns and a settling times less than 20ns show the advantage of these shunts. They show no initial overshoot peak, no oscillations and do not need compensation box to optimize the transient behavior as known from e.g. cage shunts.
-
Product
Impulse Generators
-
Provides pulse widths (measured at the 20% rise timepoint) in the range of 130 ps to 2 ns, amplitudes as high as 100 Volts, with pulse repetition frequencies to 1 MHz.
-
Product
Surge Tester (Impulse Winding Tester)
SS6815 / SS6815F
-
Surge testers (impulse winding tester) is used for testing and check the insulation grade of turns between turns, insulation grade of layers between layers, insulation grade of windings between turns. It is used widely for transformer, current sensor, voltage sensor, relay, contactor, inductor, motor, generator, valve coil, voice coil, etc.
-
Product
Coupler And Decoupler Used With Lightning Impulse Simulation Tester
-
All electric equipments & systems is required Impulse Simulation Test to the to be tested under the condition where the power source is applied to the product-under-test.At this test condition, the decoupler is needed to reduce the impulse flowing through the power line while testing. And the coupler which is inserted between tester and product, to simulate the actual condition, so the electric circuit of decoupler is prescribet by IEC rules.
-
Product
Impulse Generators
-
HYPERLABS triggerable impulse generators create precise high-speed pulses with 50 to 100 ps rise time. They can be triggered by input from antennas and other signal generator systems.
-
Product
Impulse Noise Simulators
INS Series
-
A simulator to reproduce fast rise-up noises which are generated when switching ON / OFF electric current on the inductive load. It can be used for performance evaluation of electronic equipment upon reproduction of line noises which are intruded to the power supply lines or induced noises onto the telecommunication lines.
-
Product
Power Inductor - Impulse Winding Tester
19301A
-
Chroma Systems Solutions, Inc.
The Chroma 19300 Impulse Winding Tester with high/low inductance test technology has 1000V of impulse voltage and a 200MHz high speed sampling rate that satisfies most power inductor test requirements for a wide range of inductance products from 0.1uH to 100uH. The built-in Area Size Comparison, Differential Area Comparison, FLUTTER value, and LAPLACIAN value functions are able to effectively inspect coils for insulation abnormalities.
-
Product
Impulse Semiconductor High Current Integrated
Transmission Line Pulse Test System
-
The Impulse Semiconductor High Current Transmission Line Pulse (TLP) test system is the tool of choice for extracting ESD parameters for transient protection devices in a package, or at wafer level. With accuracy better than 100 milliohms at 40 amps peak current, the Impulse high current TLP is specially tailored to the needs of today's ESD device designers who must accurately measure low values dynamic resistance irrespective of breakdown voltage.
-
Product
Impulse Response Measurements
Dirac
-
Dirac is a sophisticated tool to calculate a very wide range of acoustical parameters from impulse response measurements of an enclosure. Through many years of development and customer feedback, Dirac has grown to support many different applications. Due to its user friendly interface it is suitable for field measurements, but it also contains many advanced features that make it useful in a laboratory or research setting.
-
Product
Impulse Voltage Generator
GDCY
-
The impulse voltage generator is mainly used to the field of impulse voltage tests by lightning impulse voltage full wave, lightning impulse voltage chipped wave and operate impulse voltage wave for such test products as electrical instrument.
-
Product
.13u ESD diode
Impulse TSMC
-
The Impulse TSMC .13u ESD diode was made to provide ESD discharge paths when integrating third party IP in an integrated circuit design for total ESD protection. The Impulse ESD diode has been successfully used with Dolphin Technologies, Artisan/ARM, TriCN/Synopsis I/O libraries, as well as popular IP blocks from RAMBUS, Chip Idea and other quality IP vendors. A 5.5 volt reverse bias anode to cathode operational specification enables the Impulse TSMC .13u ESD diode to be the device of choice for 5 volt tolerant designs.
-
Product
Impulse Tester
MIG2412SPD
-
The MIG2412SPD is a impulse tester for testing SPD (Surge Protection Devices) in accordance with IEC 61643-1 and VDE 0675. Up to maximum 24kV/12kA making it suitable for testing Class I to III or in accordance with VDE Class A,C, D. The MIG2412SPD is a hybrid generator with a voltage wave shape 1,2/50 ìs at "no load" and a current wave form 8/20 ìs at short circuit for testing Class III (D) SPD connected to power line.
-
Product
Sound Level Meter & Real-time Analyzer
824
-
The Larson Davis System 824 combines advanced sound level meter and real-time analyzer capabilities into a rugged, user-friendly, ergonomic package. The base unit is an Integrating Sound Level Meter (ISM) that meets Type 1 Standards and offers simultaneous measurement of sound pressure levels using fast, slow, and impulse detectors, for A, C, and flat frequency weightings. This feature, termed ANY LEVEL™ measures 48 sound pressure parameters at once with a linear, 105 dB range. With firmware enhancements, the base unit expands as needed to accommodate multiple data processing requirements
-
Product
Current Probes
-
Teledyne LeCroy current probes do not require the breaking of a circuit or the insertion of a shunt to make accurate and reliable current measurements. Based on a combination of Hall effect and transformer technology, Teledyne LeCroy current probes are ideal for making accurate AC, DC, and impulse current measurements.
-
Product
Noise Analysis Software
noiseLAB
-
noiseLAB is a professional software recording and analysis package for making Type 1 Precision measurements to international standards. Precision Recorder: noiseLAB makes high quality recordings of up to 8 channels of sound. Precision Analysis of: Sound Level (Fast, Slow, Impulse, Taktmak. Custom Time Constant, Leq). Statistical Values (L1, L5, L10, L50, L90, L95, L99). Octave Spectra (1/1, 1/3, 1/6, 1/12, and 1/24th octave).....
-
Product
Audio Test Tone Generator
ToneGenerator
-
Tone Generator is a sine wave generator, frequency generator and signal generator that lets you create audio test tones, sweeps or noise waveforms using your computer or a PDA handheld. Generate sine wave, square wave, triangular waveform, saw tooth waveform, impulse, white noise and pink noise.
-
Product
Impulse Test Generator
SUG-CCITT-A
-
Impulse Test Generator SUG-CCITT-A (1a. 10/700us, 6KV, figure is according to N.1 in IEC60950-1:2005 Annex N). N.1 ITU-T impulse test generators.
-
Product
FPGA Impulse Response (FIR) Filter Fo Gage Digitizers
eXpert / Finite Impuls Response (FIR)
-
The onboard FIR Filtering eXpert FPGA DSP feature is a powerful method for removing unwanted signal features (like noise) and emphasizing signal features of interest.
-
Product
Magnetizing Power Supply
-
This is a magnetizing power supply which can be used even in areas (countries) with an unstable electricity supply.The accuracy of the repeating magnetizing voltage enhances our reputation for top-class quality in the industry.We confirm the peak value, the time of electrification, and the electrical current area by using an impulse meter (a highly accurate magnetizing ammeter) before we ship out the products.
-
Product
Pre- Locator
CFL PL4
-
CFL PL4 Power Cable Fault Locator is a portable, easy to use cable fault pre-location instrument. It uses the Time Domain Reflection (TDR), Secondary Impulse Method / Multiple Impulse method (MIM) and Impulse Current Method (ICM) on low, medium and high voltage cables. Its measuring ranges enable pre-location on cable lengths from 500 m to 64km.
-
Product
Pulse Signal Amplifier
VCH-606
-
The pulse signal amplifier VCH-606 is designed to multiply a single pulse or a sequence of pulses to 16 independent outputs. The impulse signal amplifier includes 16 independent channels with unity gain each for connecting consumers of impulse signals with an input impedance of 50 Ohm.
-
Product
True Dual-Channel Analysis on iOS
IOScope
-
With IOScope, measure loudspeaker impedance, frequency response, and sensitivity. Measure a room impulse response. Tune a large sound reinforcement system, time-align a set of surround sound speakers, or optimize your home stereo. Determine the actual cutoff frequencies of your latest speaker crossover circuit, or teach your students the fundamentals of Fourier analysis of dynamic systems.
-
Product
AC Insulation Testing
-
Weshine Electric Manufacturing Co., Ltd
High-voltage Dividers (High Potential Divider) are used to measure voltages and decouple partial discharges in high-voltage test systems. Depending on the specific type, they are used to measure alternating voltage (AC), direct voltage (DC), lightning impulse voltage (LI), and switching impulse voltage (SI) systems. High-voltage dividers by HIGHVOLT comply with the relevant IEC standards. The systems are available for both indoor and outdoor use.
-
Product
Impulse-Calibration-System
KAL1000 Series
-
The impulse calibration system KAL1000 is a modular system to perform tests on complete impulse voltage measuring systems and on digital recorders for the measurement of high impulse voltages and impulse currents. The modular design allows an optimal KAL-configuration depending on the actual application.Additional, this modularity allows to up-grade or modify and existing KAL1000 system in case of changing or additional requirements
-
Product
4-Channel, Sigma-Delta ADC Function Card
ProDAQ 3430
-
The ProDAQ 3430 is a 4-channel, sigma-delta ADC function card. Every channel contains front-end conditioning circuitry followed by a sigma-delta ADC. The bit stream from every ADC is then directed to finite impulse response (FIR) decimation filters. Users can activate up to 10 stages of the FIR filters. The filtered data from the selected stages is then stored in the FIFO. The data from the FIFO easily can be moved on-the-fly to the motherboard or to the host.
-
Product
Discharge Tester
-
It is a new impulse winding tester that incorporates high precision, a wide range of functions, various expandability, improved operability, and a full range of external communication interfaces.
-
Product
Qualification and Quality Control Tests
Techsquare
-
New IEC standards, IEC 60034-18-41 and IEC 60034-18-42, have been issued to define the procedures for testing partial discharge inception voltage and the long-term performance (endurance) of Type I and Type II insulation systems used in rotating machines fed from voltage converters. Voltage impulse generators are required at least to test turn insulation, but they would be recommended for any testing under power electronics supply because of their capability to simulate the real electrical stress conditions. More generally, any type of electrical insulation system when subject to impulsive voltage waveform during life should be carefully evaluated in terms of partial discharge and endurance behaviour. This is why voltage impulse generators able to provide impulses with controlled amplitude and frequency are needed to face this new testing challenge.
