-
product
Attitude Heading Reference System
(AHRS) TRAX2
Using its unrivaled magnetic sensor expertise , PNI fuses its proprietary magnetic sensors and sensor fusion algorithms, delivering accurate AHRS heading without the need for GPS.
-
product
Redundant Reference Frequency Shaper
CH7-317
Redundant reference frequency shaper Ch7-317 is designed to generate and reproduce frequency and time signals protected from frequency and phase failures based on the results of signal processing from a group of frequency and time keepers.
-
product
Reference Measuring System
SMG-R
Reference peak voltage meter SMG-R for precise measurement of high voltage. This PEAK voltmeter has higher accuracy and the measuring divider has a very high stability.
-
product
Reference Radiators / Comb Generators
The Spectrum Generator is a family member of the Schwarzbeck pulse generators, which are used as pulsestandard world wide. Whilst the latter one uses a bounce free relay contact to discharge a coaxial lineto the load resistor, it uses a special avalanche transistor instead of the relay contact.
-
-
-
product
20 Bit Dual-Channel Reference Source
DRS20
The DRS20 is a dual-channel reference source offering ultra high precision and stability and provides a +/-10 V output. The output current can be up to 10 mA and the 4 wire connection provides a 1 µV/mA load regulation. The high precision and stability is achieved by using a temperature controlled voltage reference.
-
product
Shunt Voltage References
Analog Devices offers a broad line of shunt precision voltage references that combine excellent accuracy and temperature stability with low noise and small packages. These devices operate in a manner that is functionally equivalent to a Zener diode. The bias current must be set higher than the sum of the maximum quiescent current of the voltage reference and the maximum expected load current. Since shunt voltage references are typically biased with a resistor, the voltage reference can operate on a wide range of input voltages.
-
product
Wireless Device Functional Test Reference Solution
The Keysight S8890A Wireless Device Functional Test Reference Solution provides an automation environment which is both simple to use, yet comprehensive and powerful. Based on the Test Automation Platform www.keysight.com/find/TAP, S8890A provides optional instrument driver/plug-ins offering simplified logically grouped control steps. These steps can be sequenced, looped and swept to provide powerful individual test cases or comprehensive sequences. Each driver/plug-in is provided with extensive starter sample test cases which can be modified by Keysight or the end user the UE to be tested. Plug-in options:
-
product
Intelligent Reference
TM-4D
The Intelligent Reference/TM-4D™ breaks new ground for time and frequency references. For the first time, it is possible to generate and distribute both analog and digital signals to multiple instruments and locations with just one product that fits in a single rack space. The TM-4D is three instruments in one: an Intelligent Reference/TM-4™ precise time and frequency reference, a digital signal distribution amplifier and an analog distribution amplifier. And it eliminates the need for multiple boxes.
-
product
DIP Jumpers
Series 100 thru 111
DIP Jumpers. Aries offers a wide array of DIP jumper configurations and wiring possibilities for all your programming needs. Protective covers are ultrasonically welded on and provide strain relief for cables. 10-color cable allows for easy identification and tracing.
-
product
Reference Sources
A physical or digital document that you would refer to for more information about a topic.
-
product
RF Reference Sources
The 27 GHz 96270A and 4 GHz 96040A Low Phase Noise Reference Sources are designed specifically for RF calibration, featuring a calibration-oriented interface, precision signal level and attenuation, high signal purity and precision low distortion modulation. Both instruments simplify the process of RF calibration by reducing the amount of equipment and simplifying the calculations required.
-
product
ETX® Reference Carrier Board in ATX Form Factor
ETX-Proto
The ETX-Proto is an ETX Reference Carrier Board in standard ATX form factor. Together with the ETX module of your choice and off-the-shelf add-on cards, you can quickly emulate the functionality of your desired end product for software development and hardware verification. The ETX concept has a great many advantages over full custom designs. It reduces engineering complexity, lowers the threshold for total project quantity and last but not least brings your product to the market in no time.
-
product
LTE/LTE-Advanced Multi-Channel, Reference Solution
Gain greater insight faster with a compact, multi-channel LTE-A PXI signal generator and signal analyzer reference solution.This Reference Solution uses world-class Signal Studio software to create complex LTE-A waveforms and the 89600 VSA/WLA software to connect to multiple analyzers. The VSA software allows engineers to quickly view multiple antenna elements simultaneously and analyze the RF performance and modulation domains for timing and signal quality issues in complex carrier aggregation and MIMO/beamforming designs.
-
product
Jumper Cables For Multiport Configuration Of M937xA PXI VNA
Y1242A
Use Keysight Y1242A Jumper Cables for multiport configuration of the M937xA PXI Vector Network Analyzer (VNA).
-
-
product
802.11ad Testbed, Reference Solution
Generate and analyze 802.11ad fully coded PHY waveforms for complete component, subsystem, and system performance at baseband, IF, and millimeter-wave. This Reference Solution combines Keysight Technologies software and hardware to provide a flexible testbed for 802.11ad waveform generation and analysis. Software provides the flexibility to generate and analyze 802.11ad waveforms with a wide range of different attributes. Hardware provides the flexibility to support baseband, IF, and millimeter-wave test planes. Create waveform sequences with unique 802.11ad packet structures including Modulation Coding Scheme (MCS), packet length, payload data type, and interpacket gap length, etc.
-
product
COM Express® Type 7 Reference Carrier Board in ATX Form Factor
Express-BASE7
The Express-BASE7 is an ATX size COM Express Type 7 reference carrier board. Together with the COM Express Type 7 module of your choice and off the shelf add-on cards, you can quickly emulate the functionality of your desired end product for software development and hardware verification.
-
product
Remote Radio Head Test, Reference Solution
The Remote Radio Head Test, Reference Solution provides the physical interfaces together with the vector signal analysis and vector signal generation you need to carry out comprehensive functional and performance testing of your RRH). Fully characterize the uplink and downlink, RF air-interface to and from the digital "front-haul".
-
product
Reference Cells
Reference cell is used for measuring and setting the intensity of solar simulators for one sun (or other user desired) intensity condition. They are also used to calibrate the IV Measurement system photo-detector intensity to match the measured ISC to calibrated ISC.
-
product
Heavy Duty Circuit Tester / Jumper
32900
Heavy-duty circuit tester for checking low voltage up to 12 volts. By depressing the red button the tester becomes a jumper for powering electrical components or a ground. The probe, handle, cord and clamp are reinforced for durability. Comes with a strain relief spring on the cord.
-
product
SMARC 2.1 Reference Carrier Board with M.2 Extension
I-Pi SMARC Plus
The I-Pi SMARC Plus is small (110mm x 110mm) SMARC reference carrier board based on SGeT SMARC (Smart Mobility ARChitecture) 2.1 hardware specification. Together with the SMARC short size module of your choice and off the shelf add-on cards, you can quickly emulate the functionality of your desired end product for software development and hardware verification.
-
product
COM Express® Type 6 Reference Carrier Board in ATX Form Factor
Express-BASE6
The Express-BASE6 is an ATX size COM Express Type 6 reference carrier board. Together with the COM Express Type 6 module of your choice and off the shelf add-on cards, you can quickly emulate the functionality of your desired end product for software development and hardware verification.
-
product
Shaper Of The Reference Frequency
MFC
The mezzanine module (mezzanine) of the MFC is designed to reproduce on six output lines high-precision frequency values obtained by dividing the frequency from the built-in reference frequency generator.
-
product
Deci-Center™ Jumpers
Series 112, 113 & 114
Deci Center Jumpers. Reliable, electronically tested solder connections. Pitch bars help maintain .100 [2.54] conductor spacing. 10-color cable allows for easy identification and tracing.
-
product
SR Series AC Reference Supplies
Computer Conversions Corporation
The SR Series are miniature, low cost AC reference generators designed to supply 26 or 115 Volt excitation to Synchros or resolvers in military and industrial control applications. They accept +/- 15V DC and provide up to 5VA of transformer isolated output power. These converters are packaged in PC card mounting modules 2.6" x 3.1" x 1"H.
-
product
Reference Electrode Kit
SC-4
The Model SC-4 Sliver-Silver/Chloride kit come complete with everything necessary to conduct field tests both ON SHORE and OFF SHORE.
-
product
Attitude Heading Reference System
M&M Modules
PNI’s M&M modules will self adapt and learn its system and its environment automatically to provide accurate quaternions, heading, pitch and roll. All while using 100 times less power than traditional AHRS modules.
-
product
Reference Transmitter
81492A
Keysight's 81492A Reference Transmitter is designed to offer excellent eye quality for NRZ and PAM4 signals at baud-rates up to 56 Gbaud and can serve as universal single-mode E/O converter. In addition to the internal lasers at 1310 & 1550 nm, an external optical input for usage with tunable laser sources is available. It is fully integrated into Keysight’s Optical Receiver Stress Test solutions to address test requirements of IEEE 802.3 10,40,100 and 400GBASE optical standards.
