Filter Results By:
Products
Applications
Manufacturers
Band-pass Filters
Refine signal, allowing transmission of only frequencies within a specified, continuous frequency band, while predictably attenuating frequencies above and below the continuous band.
-
product
Waveguides
Waveguides from Fairview Microwave consist of coaxial adapters, bandpass filters, bends, flexible waveguide cables, waveguide gain horns, sections and terminations. Fairview waveguides are available in standard sizes from WR-430 through WR-15 depending on type of waveguide product, which encompasses frequencies from 1.7 GHz to 75 GHz.
-
product
Miller 400D
44550
No need to select ranges or adjust dials – the Miller 400D provides a direct read-out of resistance with the push of a button• Bluetooth interface allows optional data-logging via a Bluetooth-enabled PC (or PDA)**• Rugged, hard plastic case - safe to use on wet ground – IP67 rating for dust and water intrusion• Resistance measurement range from 0.01Ω to 10MΩ (auto-ranging) • High resolution digital display• Resistance measurements are unaffected by any stray interference signals that may be present in the earth during readings, due to the use of narrow band-pass filters centered at 82.2Hz (the unit’s operating frequency)• Runs on a set of replaceable D-cell alkaline batteries...no need to periodically recharge the unit or to plug it into a power source• Performs 10,000 single readings on a fresh set of batteries• Integrates with Universal Rectifiers’ Soil Depth Selector/Multi-Pin Cable Harness System (please see Integration with Universal Rectifiers’ Cable Harness)
-
product
High-Power Tunable Filter
CB503
The need for tunable filter technology originates from the fact that high power communication systems and IED Jammer transmitters severely limit the use of tactical radio communication systems on the battlefield.This clash within the radio’s spectrum during tactical missions is often de-conflicted using fixed high Q, high power RF bandpass and bandstop filters installed prior to mission. This can limit operational effectiveness due to the potentially large number of fixed filters required within the allocated radio communication channels, which need be transported, stored in the field, and fitted by trained personnel. Many of these fixed filters centred within the octave wide tuning range could be replaced by a single high-Q tunable filter.
-
product
Spectrum Marker Generator
NSG-2
National RF, Inc. is pleased to announce the production of a new device, the Type NSG-2 Spectrum Marker Generator. The generator is intended to be used with either spectrum analyzers or communications receivers to mark specific frequency intervals in the RF spectrum. When used with receivers, it is essentially a frequency calibrator, thus making it attractive for use with vintage receivers with analog dials. The NSG-2 provides a leveled amplitude output over nearly 100 MHz of RF spectrum, thus making it ideal to mark frequencies and signal levels on spectrum analyzers. In addition, it may be used with a spectrum analyzer, in lieu of a sweeping type generator, to align lowpass, highpass, and bandpass filters with passbands greater than 20 KHz.
-
product
Precision Low-Loss Multiplexers
Maury’s line of diplexers (DP-series) and triplexers (TP-series) are designed for applications which require combining/ splitting signals at or around harmonic frequencies (nFo) and are connectorized for design-in and test and measurement applications.DP-series diplexers are designed using low-pass and high-pass filters and pass bias between the low-frequency (or Fo) port and the common (or DUT) port.TP-series triplexers are designed using low-pass, bandpass and high-pass filters and pass bias between the low-frequency (or Fo) port and the common (or DUT) port.Power handling is rated at 100W CW (average) and typical insertion loss is better than 0.5dB between the low-pass (Fo) and common ports.DP- and TP-series multiplexers are ideal accessories for passive, active and hybrid-active multi-harmonic load pull systems.
-
product
Low-PIM, High-Power Filter Solutions for Monitoring Broadband Emissions
Enables monitoring of PIM to 13 GHz; 100W CW and 1KW peakNear-end monitoring: Carriers rejected -90dB by the notchtravel through the bandpass filter to the low PIM termination.Far-end monitoring: Carriers rejected -90dB by the highpass,IM products passed are monitored by the spectrum analyzer.
-
product
1 MHz Bandwidth Voltage Preamplifier with Bandpass Filter
EC6081 mk2 - preamplifier
The EC6081 mk2 (VP2000) is a 1MHz bandwidth voltage preamplifier with bandpass filter that is designed for uses in conjunction with piezoelectric hydrophones. VP2000 offers excellent low-noise performance over the entire frequency range; and adjustable gain selection. A range of 12 high-pass and 12 low-pass filters are available, these allow ideal band pass filter settings.
-
product
Wide Band Filters (multi-octave)
GEN3-ERF®
The 3rd Generation Mini-ERF is a Reduced SWaP-C, 30 to 520 MHz tunable bandpass filter that features 50mW (typ.) power consumption, 1 Watt CW continuous power handling (7% BW), +40 dBm IIp3 (typ.), low insertion loss, and 4 dB typ. selectivity @ +/-10%, (7% filter). The GEN3-ERF’s are fully tuned and tested by Pole/Zero® for convenience and ease of use.
-
product
Seismic Signal Conditioners
Seismic signal conditioners are designed to accept an input from (and provide power to) a seismic sensor. They convert the signal to a proportional 4-20mA DC signal that can be used as an input to process control instrumentation such as a PLC or DCS. They provide additional convenience features such as optional displays, BNC connectors for access to the dynamic sensor signal, and bandpass filtering. Metrix offers seismic signal conditioners that can accept either acceleration or velocity sensors, and are available with or without an integral display.
-
product
Tunable Edge Filters
Tunable edge filter is a customized product. It usually belongs to 2-port optical tunable filter product platform. Instead of using narrow bandpass filter in the 2-port tunable optical filter, the tunable edge filter utilizes a low-pass or long-pass interference filter. By changing the incident angle of the light beam, the cut-off wavelength will be tuned. Standard Tunable edge filters support C-band or L-band wavelength range.
-
product
Broadcast Filters VHF TV
RFS bandpass filters are primarily used as part of multi-channel combiner facilities but can also be used to eliminate spurious emissions and increase isolation between co-sited services.
-
product
Band Pass Filters
*High power handling 200W with a wide range of bands available*Excellent Isolation with Low Intermodulation*High reliability of >500K Hours MTBF and multi-strike lightning protection*Support for 7-16 or 4.3-10 connectors and optional 19 inch rack mount kit*Designed and produced to ISO 9001:2008 certification standards for reliability and quality
-
product
Diplexers
ISM and RFID bandpass filter PE8700 from Pasternack is part of our extensive in-stock RF components for sale. Our ISM and RFID band pass filter is manufactured with SMA connectors that are female and in a 4 section design. This 4 section SMA bandpass filter for ISM and RFID has an insertion loss of 1.500 dB and a maximum power of 5 Watts.
-
product
Low Pass and Bandpass SMA Coaxial Filters
Fairview Microwave’s bandpass filters were developed for use in various applications including GPS, ISM, RFID and Wi-Fi systems and operate in several bands, some as low as 824 MHz and some as high as 5.875 GHz. Fairview’s low pass filters allow for tailoring of a test setup for a specific application and support upper band edges of 100, 225, 400, 1000, 2000 and 3000 MHz. All of these bandpass filters and low pass filters feature female SMA connectors.
-
product
Tunable Filters - Digitally Controlled
K&L Microwave offers a variety of Tunable Filter Products to satisfy a broad range of filtering applications. Tunable Bandpass and Bandreject filters provide the best solution for pre-tuning the desired signals while rejecting the interfering signals. The method of tuning can be either mechanical via a tuning knob mounted on the front of the filter, or electro-mechanical via an optional remote digital interface such as GPIB, RS-232, RS-422, BCD, ARC171, ARC234, Ethernet, USB or "Thumbwheel" panel mount.
-
product
MEGA-POLE® Series
MEGA-POLE™
The MEGA-POLE filter series covers the standard frequency bands within the 30 to 450 MHz range. This new filter series provides excellent selectivity while maintaining very low insertion loss. The product line also has exceptional RF power handling capability with a high third order intercept point. The MEGA-POLE filter series can be used for transmitter applications to reduce power amplifier noise, harmonics and intermodulation products, to provide bi-directional filtering directly at a transceiver’s antenna port, or other applications requiring extremely linear, high power RF bandpass filtering. It has been designed for rugged military environments per MIL-STD-810.
-
product
High Frequency Tunable Bandpass Filters
CTB Series
Tunable Ranges Up To 8 GHz. Bandwidths 1% to 5% of Tuned Center Frequency. Digital Control Offered in Various Inputs, including GPIB (standard), RS-232, RS-422, and USB. Custom Interfaces Available.
-
product
Tunable Filters
K&L Microwave offers a variety of Tunable Filter Products to satisfy a broad range of filtering applications. Tunable Bandpass and Bandreject filters provide the best solution for pre-tuning the desired signals while rejecting the interfering signals. The method of tuning can be either mechanical via a tuning knob mounted on the front of the filter, or electro-mechanical via an optional remote digital interface such as GPIB, RS-232, RS-422 or BCD.
-
product
Waveguide Bandpass Filters
More details on PE-W28F001 WR-28 band pass wave guide filter can be found on the the waveguide bandpass filter design datasheet specifications up above. WR-28 waveguide bandpass filter from Pasternack is in stock now at our Irvine, CA facility. Our waveguide bandpass filter with WR-28 flanges is part of over 40,000 components for RF, microwave and millimeter wave applications in-stock which are available to ship same day worldwide.
-
product
Bandpass Filters
These bandpass filters utilize a suspended stripline design to obtain a very compact configuration. Applications include wideband receiver input preselection and output filtering of frequency multiplied RF power sources.
-
product
Optical Filter Sets
Our filter sets support a great range of fluorophores for microscopes and imaging systems. Patented design techniques drive some of the most spectrally sophisticated optical filters on the market. High transmission, steep edges, precise spectral edge placement, and optimized blocking combine for more reliable measurements. A wide selection of individual bandpass filters and dichroic beam-splitters support unique applications, and world-class manufacturing and cutting-edge metrology ensure consistent performance that always meets specifications.
-
product
Bandpass Filters
ISM and RFID bandpass filter PE8700 from Pasternack is part of our extensive in-stock RF components for sale. Our ISM and RFID band pass filter is manufactured with SMA connectors that are female and in a 4 section design. This 4 section SMA bandpass filter for ISM and RFID has an insertion loss of 1.500 dB and a maximum power of 5 Watts.
-
product
Bandpass
BSC Filters QuEST tool allows you to start designing your own custom Bandpass Filter, download s2p files of performance and send that design to the factory for manufacture.
-
product
2-Port Optical Tunable Filter
Optoplex's Tunable Optical Filter, also known as Optical Tunable Filter or Tunable Bandpass Filter, is an integrated module, consisting of micro optics and electronics. When receiving a stream of optical signals of a plurality of wavelengths from the Input-Port (IN), the 2-port tunable optical filter directs a selected channel to the Output-Port (OUT). The selected channel can be varied (tuned) within the operating wavelength (frequency) range by a remote command sent through the built-in control PCB and firmware.
-
product
Passive Component Integration
Integrate passive optical components of your choice such as WDM couplers, splitters, band-pass filters, PM beamsplitters and circulators. PXIe and benchtop models support SMF, MMF and PMF.
-
product
Bandpass Filters
K&L Microwave provides bandpass filters in multiple topologies built to customers' electrical, mechanical, and environmental specifications. The list below contains part numbers meeting existing industry and customer specifications, as well as product families. Use the quote cart to request a quote on a specific design.
-
product
SWITCHABLE FILTER BANKS
FLT-1 WB
Matrix Test Equipment Incorporated
The Model FLT-1-WB is our Wide Bandpass filters for measuringthe Video Carrier and the Composite Second Order Beatdistortion on both sides of the carrier.
-
product
LTE/WiFi Test Box - Adjustable Bandwidth Tunable (700MHz - 6000MHz)
K&L has developed and is now shipping an LTE/WiFi testing solution digitally-controlled filtering system that can tune a bandpass filter anywhere in the 700 MHz to 6000 MHz range with continuously adjustable bandwidth. View latest video to see in operation.
-
product
Wavelength Meter
S-107
Wavelength meter slot module of FOTS system offers two main functions of an accurate wavelength meter and a precise tunable band-pass filter. This accurate instrument, which is based on an internal tunable filter, acts as an optical spectrum analyzer or a wavelength meter as well as a low insertion loss tunable filter. The built-in tunable filter of the module is precisely tuned in C-band and L-band optical communication window by using both electronic and optical controlling methods. User can choose the function of this module depending on his or her applications.
-
product
Bandpass Filter Components
Is a device that passes frequencies within a certain range and rejects (attenuates) frequencies outside that range.
