Filter Results By:
Products
Applications
Manufacturers
Low Pass Filters
Refine signal, allowing the transmission of signal below a specific corner frequency, while attenuating the frequencies above.
See Also: Filters, Filter / Amplifiers, EMI Filters, Programmable Filters
-
product
2- to 8-Channel Anti-Alias Low-Pass Filter and Instrumentation Amplifier Card
AAF-3PCI
The AAF-3PCI is a 2- to 8-channel anti-alias low-pass filter and instrumentation amplifier PCI bus plug-in board for front-end signal conditioning in PC-based data acquisition systems.
-
product
Precision Low-Loss Multiplexers
Maury’s line of diplexers (DP-series) and triplexers (TP-series) are designed for applications which require combining/ splitting signals at or around harmonic frequencies (nFo) and are connectorized for design-in and test and measurement applications.DP-series diplexers are designed using low-pass and high-pass filters and pass bias between the low-frequency (or Fo) port and the common (or DUT) port.TP-series triplexers are designed using low-pass, bandpass and high-pass filters and pass bias between the low-frequency (or Fo) port and the common (or DUT) port.Power handling is rated at 100W CW (average) and typical insertion loss is better than 0.5dB between the low-pass (Fo) and common ports.DP- and TP-series multiplexers are ideal accessories for passive, active and hybrid-active multi-harmonic load pull systems.
-
product
Programmable Anti-Alias Low-Pass Filter and Instrumentation Amplifier
USBPGF-S1
Single Channel USB Programmable Anti-Alias Low-Pass Filter and Instrumentation Amplifier for Signal Conditioning in Data Acquisition Systems. Differential or single ended input. 10Vmax Signal Input and Output with input protection up to 40V. Software-programmable instrumentation amplifier gains of 1 to 1000.
-
product
Dual 10th Order Lowpass Filter
64-VBF
The 64-VBF 10th order Lowpass Filter is a dual channel filter with independent switch settable Cutoff Frequency (Fc). The filter has a linear phase DC accurate root raised cosine response. The unit’s differential inputs are built to withstand high DC over-voltages up to ±50 VDC and greater than ±100 V transients. Gain of the unit is 1 allowing for minimal insertion issues. The output can drive a high speed DAQ multiplexer with its fast settle and capacitive drive capability.
-
product
PXI I/O Module for Sound and Vibration
JSV-4498-PXI
16-channel ICP analog voltage input Maximum sample rate: 204.8KS/s; simultaneous acquisition Analog-to-digital converter: delta-sigma, 24 bits Phase accuracy < 0.02deg@10KHz Maximum analysis bandwidth：96KHz Input range from ± 10 V to ± 316mV Coupled mode：AC Signal conditioning: anti-aliasing filter Digital filter: user-defined low pass, high pass, band pass, band stop Dynamic range：114 dB ICP Current：0-4 mA, optional Overload indication: software displa
-
product
Dual Voltage Buffer with Current Drive
BUF-01
The BUF-01 Voltage Buffer is a dual channel buffer capable of driving up to 50 mA of current on each channel at up to ±10 V output. The buffer has a 2nd order low pass filter with 3 dB point of 119 kHz to remove high frequency noise. The unit’s differential inputs are built to withstand high DC over-voltages up to ±50 VDC and greater than ±100 V transients. Gain of the unit is 1 allowing for minimal insertion issues.
-
product
Spectrum Marker Generator
NSG-2
National RF, Inc. is pleased to announce the production of a new device, the Type NSG-2 Spectrum Marker Generator. The generator is intended to be used with either spectrum analyzers or communications receivers to mark specific frequency intervals in the RF spectrum. When used with receivers, it is essentially a frequency calibrator, thus making it attractive for use with vintage receivers with analog dials. The NSG-2 provides a leveled amplitude output over nearly 100 MHz of RF spectrum, thus making it ideal to mark frequencies and signal levels on spectrum analyzers. In addition, it may be used with a spectrum analyzer, in lieu of a sweeping type generator, to align lowpass, highpass, and bandpass filters with passbands greater than 20 KHz.
-
product
EMI/EMP Connectors
Filter connector series includes EMI/ EMP/ESD circular, ARINC, D-subminiature and micro-D connector styles. They can be combined with high energy TVS diode technology to achieve lightning and EMP transient protection. Smiths Interconnect's EMI filter connectors use multi-layer ceramic capacitor arrays together with inductive materials to realize robust, high performance low pass filter networks. Where required, transient protection can be combined with EMI /RFI filtering to provide maximum protection. The diodes as well as the EMI filter are packaged separately so the construction of the connector remains modular.
-
product
Low Voltage DC / Battery Powered HV Amplifiers
WMA-02 And WMA-02LF
The Falco Systems WMA-02 is a high voltage amplifier that runs from an 24 - 30V DC power supply and can be battery powered if required, e.g. for use in a Faraday cage. Its internal high voltage generator is inductor-free and hence does not spread magnetic interference in sensitive experimental setups. The output noise is impressively low at 4mVrms. For extremely low noise applications where bandwidth is not an issue, a dedicated WMA-02LF version is available that contains an output low pass filter capacitor which reduces the bandwidth to 50Hz, but makes the noise drop to below 0.2mVrms. This bandwidth-limited amplifier is ideal for MEMS or piezo positioning with manual voltage adjustment.
-
product
16-Channel Anti-Alias Low-Pass Filter Card
AAF-16
The AAF-16 is a 16-channel anti-alias low-pass filter card series for front-end signal conditioning in PC-based data acquisition systems.
-
product
ACDC
EA Series
The EA Series of line operated power supplies features near constant efficiency over theentire rated input voltage range. These electrically identical families employ a highly efficient, closed loop ripple regulation circuit, which contains a low pass filter. Each stage, transformer, filter and regulator is engineered for maximum efficiency.
-
product
1.3GHz Frequency Counter
Model 1122 / 1122X
- Wide Frequency Range 0.2Hz to 1.3GHz- 2 Separate Channels, for LOW & HIGH Frequencies- High Sensitivity- 8 Digit Green LED Display- Microcontroller based Advance Technology- Optional RS232 Interface- Reciprocal Counting Technique for High Resolution at Low Frequency- Period Measurement- Low Pass Filter for Noisy Low Frequency (<100KHz)- 4 Selectable Gates (10ms, 100ms, 1sec, 10sec)
-
product
Handheld Digital Multimeter, 4.5 digit, up to 800 hours battery life
U1282A
60,000 counts resolution on dual display0.025% basic DC voltage accuracy Longer battery life up to 800 hours Certified to IP 67 for dust and water protection Tested to withstand a 3-meter (10-ft) drop Programmable via USB (Download Programming Guide here)CAT III 1000 V/ CAT IV 600 V overvoltage protection Vsense for non-contact voltage detection Square wave output for generating pulse width modulation (PWM) signal Frequency counter Low pass filter
-
product
Low Pass and Bandpass SMA Coaxial Filters
Fairview Microwave’s bandpass filters were developed for use in various applications including GPS, ISM, RFID and Wi-Fi systems and operate in several bands, some as low as 824 MHz and some as high as 5.875 GHz. Fairview’s low pass filters allow for tailoring of a test setup for a specific application and support upper band edges of 100, 225, 400, 1000, 2000 and 3000 MHz. All of these bandpass filters and low pass filters feature female SMA connectors.
-
product
"Standard" RF Low Pass Filters
Coaxial Dynamics "Standard" line of RF Low Pass Filters offers several models to choose from at CW power ratings of 100 watts and 200 watts. These filters cover operating frequencies from 88 MHz to 400 MHz with less than 0.5 dB insertion loss and attenuation levels of 40, 50 and 60 dB.
-
product
ACDC
EC Series
The EC Series of line operated power supplies features near constant efficiency over theentire rated input voltage range. These electrically identical families employ a highly efficient, closed loop ripple regulation circuit, which contains a low pass filter. Each stage, transformer, filter and regulator is engineered for maximum efficiency.
-
product
Industrial Clamp Meters
*Measures AC+DC current*AC and AC+DC voltage measurements with digital low pass filter for accurate readings on variable frequency drives*Also measures DC voltage, resistance, capacitance and frequency*Tests continuity and diodes*Flashlight inside clamp jaw for easier work in dark locations*Backlight & relative mode for added versatility*Peak-RMS measures motor inrush current*AmpTip™ increases accuracy on small wires and low current*Two voltage detection modes - non-contact or using a single test lead*Data hold*Recording of Maximum, Minimum, and Average readings*Crest (peak hold) feature captures current or voltage peaks as short as 5 milliseconds
-
product
Low Voltage DC / Battery Powered High Voltage Amplifiers
WMA-005 And WMA-005LF
The Falco Systems WMA-005 is a high voltage amplifier that runs from an 24 - 30V DC power supply and can be battery powered if required, e.g. for use in a Faraday cage. Its internal high voltage generator is inductor-free and hence does not spread magnetic interference in sensitive experimental setups. The output noise is impressively low at 3mVrms. For extremely low noise applications where bandwidth is not an issue, a dedicated WMA-005LF version is available that contains an output low pass filter capacitor which reduces the bandwidth to 50Hz, but makes the noise drop to below 0.1mVrms. This bandwidth-limited amplifier is ideal for MEMS or piezo positioning with manual voltage adjustment.
-
product
Loggers/PQA
Kyoritsu Electrical Instruments Works, Ltd.
Large capacity for storing 60,000 data points Lowpass Filter will filter out the harmonics LED flickers when the preset current/voltage value is exceeded CALL:Confirmation of recorded data Selection of One-time mode or Endless mode Non Volatile Memory Battery power indicator The userfriendly PC software "KEW LOG Soft 2" is supplied Continuous measuring time:Approx. 10 days (Alkaline Battery)
-
product
High-speed USB DAQ System
Model DI-4208
USB Data Acquisition (DAQ) System. Eight armored analog differential inputs*. Programmable range per channel: ±2, 5, 10, 20, 50 100 V full scale. Up to 120 V rms without damage. 50 dB common mode rejection. Supports ChannelStretch™ multi-unit synchronization*. Adaptable low-pass filter per channel. Corner frequency set as a function of sampling rate. 16-bit analog-to-digital resolution. 160 kHz analog sample throughput rate. Seven digital ports*. Programmable per port as input or switch. Support for rate measurements to 50 kHz. Support for 16-bit counter.
-
product
Filter Building Blocks
Analog Devices offers an extensive line of continuous time and clock tunable (switched capacitor) filter building blocks. These devices were designed to simplify the implementation of band-pass, high-pass, low-pass, notch, or all-pass filters using classical filter realizations (such as Butterworth, Cauer, Bessel, and Chebyshev).
-
product
Lowpass Filters
Frequency range of this lowpass filter is DC to 100 MHz and the passband is 100 MHz. PE8719 lowpass filter is one of over 40,000 RF, microwave and millimeter wave components supplied by Pasternack. Our 5 section low pass filter can be bought and shipped worldwide the same-day as with our other in-stock RF parts.
-
product
0.1Hz-3.7GHz Frequency Counter
FC-3000
Features:*Frequency measuring range: 0.1Hz to 100MHz in A input, 80 MHz to 3.0GHz in C input.*Period,Total and RPM measurement for input A*9 Digit display with 0.01mHz resolution in 1 Sec (By Ext.Reference signal).*RS-232C serial interface function for communication with computer.*High sensitivity Extemal reference input function(>=1.5Vrms).*Peciprocal technique for high resolution at low counting frequencies .*Self check function executed to perform a automatic self diagnosis of various counter function.*Push-scanning for selecting Function and Gate time.*Low-pass filter(100KHz,-3dB)installed for removing noise signsl in low frequency measuring.*AC/DC coupling function(Selectable AC/CD Coupling)*10:1 Input Attenuation(Selectable×1/×10 Attenuator)*Data hold function
-
product
Multi-channel low-pass filter board
AAF-2
The AAF-2 is a multi-channel low-pass filter board designed for use in front of A/D converters with resolution up to 16-bits. It is ideal for filtering applications in sound and vibration testing, ultrasonics, acoustics, structural analysis, industrial, test, scientific and laboratory data collection and applied mechanical applications in electronics, aerospace, field research, automotive, and process control industries.
-
product
Dual Channel 180 MS/s Digitizer PXI / PXIe Card
GX2482
The GX2482 series are a high performance, dual differential channel, 16-bit digitizer offering high dynamic range and excellent SFDR. The module’s differential inputs, coupled with its low distortion makes it an ideal instrument for analyzing high performance or low level analog signals. Each channel offers 3 selectable low pass filters, a 16 bit, 180 MS/s ADC, and 64 M words of memory for each channel.
-
product
Low Voltage DC / Battery Powered HV Amplifiers
WMA-01 And WMA-01LF
The Falco Systems WMA-01 is a high voltage amplifier that runs from an 24 - 30V DC power supply and can be battery powered if required, e.g. for use in a Faraday cage. Its internal high voltage generator is inductor-free and hence does not spread magnetic interference in sensitive experimental setups. The output noise is impressively low at 3mVrms. For extremely low noise applications where bandwidth is not an issue, a dedicated WMA-01LF version is available that contains an output low pass filter capacitor which reduces the bandwidth to 50Hz, but makes the noise drop to below 0.1mVrms. This bandwidth-limited amplifier is ideal for MEMS or piezo positioning with manual voltage adjustment.
-
product
Programmable, 2-Channel Low-Pass Filter Module
AAF-3F
Programmable, 2-Channel Low-Pass Filter Module. The AAF-3F is designed for use with the AAF-3M and AAF-3PCI filter boards.
-
product
Dual Channel Multi-Band FM Tracking/Data Receiver In Modular Style Housing
LS-27-B
The Lumistar LS-27-B Modular Dual Channel Tri-Band Tracking and Data Receiver is Lumistar’s third generation of modular high performance FM Receivers. This wideband designs supports one or two independent channels of PCM with data rates up to 20Mbps. The unit includes both an optional FM demodulated output for PCM data, and standard programmable AM/linear AGC outputs for auto-tracking receivers. The design offers 8 IF Bandwidths and 8 Video Filters per channel for each receiver.AC coupling with a low pass filter is employed to ensure a high quality data link with long strings of NRZ-L ones or zeroes. The unit provides a software selectable 10 MHz reference I/O port forlocking local oscillators to a high precision external source or to arrange multiple units in a master/slave arrangement. The receiver’s control and status is achieved via Ethernet, USB or auto-switched RS-232 (or “4-wire” RS-485 in place of 232). When utilizing the RS-422 interface, multi-drop configurations can be accommodated.
-
product
Filtered Analog Input Expansion Board
MSXB 048
The MSXB 048 Filtered Analog Input Expansion Board has a four-pole low-pass Butterworth filter on each of its 16 single-ended channels. For DAP applications that require analog filters to take out all above-Nyquist frequencies before signal conversion, it simply replaces the MSXB 037 Analog Input Expansion board. Signal inputs normally connect to the MSXB 048 through a panel-mount DB-37 connector.
-
product
2 to 8 Channel Anti-Alias Low-Pass Filter Card
AAF-1
The AAF-1 is a multi-channel anti-alias low-pass filter board designed for front-end signal conditioning in PC-based or stand-alone 12-bit A/D conversion systems.
