Circuit
-
product
Small outline PCB with 72 Pin Socket
1091-001
Our small format embedded switching (SIM relay) cards offer a choice of switching configurations using low cost industry standard SIM connectors. They free the designer from the detail of routing complex switching circuits, you may select from a wide range of cards using the built in RS-232 and I2C interfaces. These low-cost embedded switching cards are intended to be mounted on to a simple motherboard. They may be used to construct very high density switching networks. SIM based switching cards also allow for very simple in-field maintenance.
-
product
High Current Transformers
High Current Transformer is designed to elevate and check the temperature of the conductors at high current levels, in order to simulate the current loading conditions found in electrical circuits. High Current Transformer is designed as an open type transformer that uses the test object as its secondary coil or has 1 or 2-turn self secondary winding. The conductors cores' temperature depends on the short-circuit high current caused by the test object. According to the current going through the test object, the test temperature of the conductor will change. The loop temperature is measured by a thermocouple probe which is directly connected to conductor.
-
product
Filter Design Software
QuickFil
QuickFil is a software for designing passive electronic filters. The result is an optimized circuit of inductors (L)and capacitors
-
product
Temperature Monitors
SIM923A
Stanford Research Systems, Inc.
The SIM923A has selectable 10 µA and 1 mA current sources to provide sensor excitation. Sensor resistance is determined ratiometrically with a half-bridge circuit consisting of the sensor and an internal reference resistor.
-
product
High-Standard Bench-Top Laser Source
Shanghai Stone Communication tech Co., Ltd
These bench-top laser source has built-in high-feature Semi-conductor laser device, it is the SM output, with less than 10MHz plus width. Based on the advanced micro-processor control system, this instrument integrated high precision ATC and ACC(APC) to control the electric circuit, in order to realize the high stable output of the laser device, and make the operation easily and directly. We also can provide user required communication port with the software to realize remote control from the PC.
-
product
VME Test Extender 3U/220mm J2
111EXT3122-12XX
The VME extender boards are designed to bring a circuit card completely out of a card cage so that it can be tested or debugged on both sides of the test board. Each signal, power, and ground line can be individually isolated with the DIP switches.
-
product
Wall-Mount Miniaturized Oxygen Analyser
Rapidox 2100-OEM-RSB-WALL
The Rapidox 2100 OEM-RSB-WALL is a wall mount version of our miniaturised 24V OEM oxygen (O2) analyser. The compact (4.5″ x 3.0″) circuit is integrated into a neat IP65 wall mount polycarbonate box, with a clear smoked hinged lid. Behind this is a clear OLED display and menu keypad. The box is completely electrically isolated and meets all UL and IEC standards for these types of enclosures.
-
product
ASA200
The ASA200 Analog Signature Analyser will assist you in testing, diagnosing and troubleshooting printed circuit boards without powering them (known as ‘power-off testing’).Connected via USB to a compatible PC running our own free software the ASA200 you can easily capture, measure and compare known good signatures (from your ‘golden’ board) with signatures from your suspect board. The built-in gate/bias generator (+/-10V, 100ohm source impedance) can be used to help test active components such as SCR’s, opto-couplers, small relays, TRIAC’s etc. An external dual footswitch can be connected to the ASA200 and can be user configured to control various functions.With the ASA200 we set out to bring the incredibly powerful technique of Analog Signature Analysis to engineers and repair shops at an affordable price.
-
product
Microprocessor System Tester
IST-6700
IST Information Scan Technology, Inc.
The IST 6700 is a low cost, stand-alone test instrument that provides a wide range of automatic and manual features for troubleshooting microprocessor-based circuit boards. It employs CPU emulation with low cost CPU personality pods to attach to or replace the resident CPU. With stored "Known Good" test data, the 6700 can provide fully automatic functional tests to check the system RAM, ROM, control signals, address, and data bus plus the measurement of the CPU clock frequency and supply voItage.
-
product
PXI 5W Programmable Resistor Module, 2-Channel, 1Ω to 239Ω
40-252-113
The 40-252-113 is a programmable resistor module with 2 channels which can be set between 1Ω and 239Ω with 1Ω resolution The 40-252 range provides a simple solution for applications requiring up to 5W of power handling per channel. The 40-252 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. Each channel is able to simulate short or open circuit conditions that can be experienced in a system caused by faulty wiring or sensors.
-
product
Standard Mechanical Calibration Kit, DC To 9 GHz, Type-N, 50 Ohm
85032F
The Keysight 85032F calibration kit contains precision 50 ohm type-N standards used to calibrate Keysight network analyzers. Standards include fixed terminations, open circuits, and short circuits in both genders. This kit is specified from dc to 9 GHz.
-
product
TestCentre
ARC has experience with complex, commercially available test executives that are available for high volume production needs. Often times, when you don’t need the horsepower of a full featured executive, you are left with creating a specifically defined test program or crafting your own test sequencer. Rather than go down this path and spending your time on architecture, TestCentre brings a simple, yet elegant solution to this all-common problem. Used in many of ARC’s standard test stations, the robust, sequence based architecture of TestCentre, allows you to focus on the testing task at hand. While having some of the more advanced features found in high-end test executives, TestCentre, when mixed with RF analyzers and PXI based test solutions are a great, low cost solution to help solve your everyday testing requirements. Along with TestCentre and an ARC supplied rack-based test platform, your test challenges can be solved in doing circuit card testing, assembly/module level testing, or depot repair troubleshooting tasks.
-
product
PXI 1A Fault Insertion Switch 22-Channel
40-195-001
The 40-195 is a 22 Channel Fault Insertion Switch, primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers. It is designed to be able to insert different fault conditions on pairs of signals between the test fixture and the equipment under test: Open-Circuit, Short-Circuit between signal pairs, Short-Circuit between signal pairs and user applied fault conditions e.g. Power or GND. Relays in-line with the signal paths allow open circuit conditions to be simulated on either side or both sides of a signal pair. Relays between each channel pair enable adjacent signals to be shorted, and relays between signal paths and the "Fault" connection allow the application of external user applied fault conditions.
-
product
PXIe-5668, Up to 26.5 GHz PXI Vector Signal Analyzer
783124-01
Up to 26.5 GHz PXI Vector Signal Analyzer - The PXIe‑5668 offers wide bandwidth with high-performance measurement performance and speed. It meets the challenging requirements of applications such as wireless communications, radio frequency integrated circuit characterization, RADAR test, and spectrum monitoring and signal intelligence. With its implementation as a PXI instrument, the PXIe‑5668 also features the fast measurement speed required for high-volume manufacturing test, and multi-instrument synchronization capabilities for phase-coherent MIMO test. You can use the optionally included PXIe-5698 preamplifier to improve dynamic range and sensitivity near the instrument noise floor.
-
product
SIMRC - 16 x Uncommitted Reed Relay, SPST
1010-R-16-1-5/1D
Our small format embedded switching (SIM relay) cards offer a choice of switching configurations using low cost industry standard SIM connectors. They free the designer from the detail of routing complex switching circuits, you may select from a wide range of cards using the built in RS-232 and I2C interfaces. These low-cost embedded switching cards are intended to be mounted on to a simple motherboard. They may be used to construct very high density switching networks. SIM based switching cards also allow for very simple in-field maintenance.
-
product
Standalone Sporadic Event Recorder For Circuit Breakers
OTM-XB
The OTM-XB is the only standalone recorder to use the vibro-acoustic method that detects intermittent and sporadic operational faults on working circuit breakers.
-
product
HV AC Test Set
SERIES S400 TYPE RX I O/ I OACP
K&S Engineering and Scientific Ltd
The output is continuously variable from zero to 10 kV by means of the panel mounted regulator. An output trip is fitted which operates when the output exceeds 25 mA switches off the test set and operates a neon overload indicator. Primary protection is provided by two panel mounted fuses. The output is protected by the output trip and a magnetic/hydraulic circuit breaker.
-
product
10-amp AC and DC Variable Power Supply
ACDC-10
The ETI Model ACDC-10 is a small, lightweight, and portable AC and DC power supply. The unit is intended for resetting circuit breaker charging motors and other general-purpose applications. It will provide DC voltage in three nominal ranges from 0-120V, 240V, and 480V at 1 kVA, as well as AC voltage in three nominal ranges from 0-140V, 280V, and 560V at 1.4 kVA. The ACDC-10 is housed in a rugged plastic enclosure approximately 20” x 11” x 18” and weighs less than 65 lbs
-
product
PWB Interconnect Stress Test
PWB Interconnect Solutions Inc.
Services to test the reliability of Printed Circuit Boards. PCBs).Coupon Inspection and Electrical Prescreen. Coupon Testing. Failure Location via I/R Photo Imagery. Failure Analysis.
-
product
Fungus Testing
Fungus can cause products to malfunction during operation and can grow on just about anything if the conditions are right. It will break down certain plastics, rubbers, paints and gaskets if it attaches itself and is left to grow. Fungus is known to short out electronic circuits.
-
product
Ground-Fault Location Products for Ungrounded Systems
When combined with Bender's ground-fault detectors and current transformers, EDS series modules provide fast, automatic ground-fault location in ungrounded systems. Fault location takes place while the system remains online without the need to open branch circuit breakers or disconnect equipment. Bender's fault location system works on both AC and DC systems, as well as systems with variable frequency drives. A standalone, portable fault location system is also available.
-
product
Yellow Industrial VOM
260-8Xi
The 260-8Xi offers all of the advantages of the Simpson 260-8, plus several new safety features. The bright yellow ABS housing is easy to see and also provides increased drop protection. The 260-8XPi includes a resettable overload protection circuit and audible continuity check. Both versions come with batteries, manual and test leads with alligator clips.
-
product
Air Core Test Lab Reactors
Test Laboratory Reactors are designed for high voltage and high power test laboratories. They are designed to withstand the most extreme electrical service conditions during test periods. Design techniques are implemented in accordance with the most demanding service conditions. These reactors are used for various purposes in test laboratories such as current limiting and synthetic testing of circuit breakers, capacitor testing, artificial line simulation etc.
-
product
PXI 10GBase-T1 Ethernet MEMS Fault Insertion Switch, 8 Channel
40-205-008
The 40-205-008 (PXI) is a 8-channel fault insertion switches designed to simulate common faults on high speed two wire communication interfaces such as xBaseT1 Ethernet. They available with 4 or 8 channels of two wire serial connections and can be used for simulating faults on 10BaseT1, 100BaseT1, 1000BaseT1 and 10GBaseT1 Ethernet interfaces. Any wire can be set as open circuit and shorts can be applied across wire pairs. Fault connections can be made to one of four external signals via two fault buses, typically simulating connections to supply voltage or ground.
-
product
PHOTOMASK INSPECTION MACHINE
NEGATIVE FILM
Negative film and photomask inspection originated from the extensive use of printed circuit boards. Negative films and photomasks are used in large quantities. The early detection method is to use the "inspection light table" for inspection, which requires too much manpower and material resources, and manual testing may be due to eye fatigue and negligence.
-
product
Multimeter Network Tester
VA16
Shanghai Yi Hua V&A Instrument Co., Ltd. CO.,LTD
Network Cable test (RJ45): Tests for open circuits, shorts, miswires, reversals, and split pairs SHIELD detection tests a cabl
-
product
1X Series Supervision Relays
The 1X series is comprised of an electromechanical voltage operated relay which is wired across the circuit being monitored. The relay may be ordered to operate in one of four (4) different application modes as described in the Technical Bulletin.
-
product
Ohmmeters
GAOTek provides state of the art, professional grade Ohmmeters for sale to the United States, Canada and Globally. GAOTek Ohmmeters are portable instruments that accurately measure electrical resistance between two points on a circuit. The Ohmmeters have their own power supply through their own battery, and are needed when the two probes (red: positive side of circuit, black: negative side of circuit) are connected to the two points in the circuit where the desired measurement is to take place. The circuit is turned off, which is when the ohmmeter sends its own current through the circuit. Units of Ohms, symbolized by the Greek letter Ω (Omega), are used as a unit of measure when measuring electrical resistance. In accordance with Ohm’s law, when the current is passing through a circuit is at its maximum, the resistance is said to be the smallest.
-
product
Digital (1kV below) Insulation Tester
1161 IN
Standard Electric Works Co., Ltd
● Microprocessor-controlled.● Measures insulation (MΩ), Continuity (Ω) and AC voltage.● Three insulation test voltages(DC V) : 250V, 500V, 1000V.● 3½ digital LCD (2000 counts).● 68 × 34mm (2.677” × 1.338” ) large LCD display.● Waterproof design, protection class : IP54.● Automatic circuit discharge.● Test insulation at rated voltage into a 1mA load.● 200mA short circuit testing current for continuity.● Auto ranging.● Fuse protection.● Data hold function● BS 16 edition.
-
product
6.8 GHz Wideband Synthesizer with Integrated VCO
ADF4356
The ADF4356 allows implementation of fractional-N or integer-N phase-locked loop (PLL) frequency synthesizers when used with an external loop filter and an external reference frequency. A series of frequency dividers at another frequency output permits operation from 53.125 MHz to 6800 MHz. The ADF4356 has an integrated VCO with a fundamental output frequency ranging from 3400 MHz to 6800 MHz. In addition, the VCO frequency is connected to divide by 1, 2, 4, 8, 16, 32, or 64 circuits that allow the user to generate RF output frequencies as low as 53.125 MHz. For applications that require isolation, the RF output stage can be muted. The mute function is both pin- and software-controllable.
