Response
-
product
DH Series QuickLink Adapter, 8 GHz BW
DH-QL
Teledyne LeCroy’s DH series 8 to 30 GHz differential probes offer the combination of bandwidth, input range and offset capability to address any high-speed probing requirement from debugging serial data interfaces to validating DDR memory systems. DH series probes provide superior loading characteristics and are calibrated with a custom “fine-tuned” frequency response. The ultra-low loading and flat frequency response ensure accurate measurements.
-
product
Portable Appliance Testing (PATs)
In response to ever growing industry requirements, Megger offers a sophisticated line of electrical product testing equipment.
-
product
True Dual-Channel Analysis on iOS
IOScope
With IOScope, measure loudspeaker impedance, frequency response, and sensitivity. Measure a room impulse response. Tune a large sound reinforcement system, time-align a set of surround sound speakers, or optimize your home stereo. Determine the actual cutoff frequencies of your latest speaker crossover circuit, or teach your students the fundamentals of Fourier analysis of dynamic systems.
-
product
15-CH Isolated Digital Output Module
ND-6056
ADLINK's NuDAM data acquisition modules make up a total acquisition network and control system. Up to 256 NuDAM modules an be romotely controlled on any RS-485 network from a host computer, via a single serial RS-232, allowing communication from as far as 4000 feet from the host. Based on the RS-485 multi-drop network system, each module has a unique address ID, whereby simple ASCII command & response protocols through the standard RS-485 interface can control all the NuDAM modules in the RS-485 network. The NuDAM modules provide direct communications with a wide variety of sensors, perform all signal conditioning, scaling, linearization and conversion, and can acquire measurements of temperature, pressure, flow, voltage, current, and multiple digital signal types.
-
product
Microphone Preamplifier
HT426E01
Nominal Microphone Diameter1/2Frequency Response Electrical Noise(at 22 C) (Flat 20 Hz to 20 kHz)Distortion (3 V rms input at 1 kHz)<-70 dB<-70 dB[1] EnvironmentalTemperature Range (Operating)-40 to +248 FExcitation Voltage 20 to 32 Constant Current Excitation 2 to 10 mA
-
product
PCI Programmable Resistor Card 2-Channel 3 Ohm To 131k Ohm - SPST
50-294-134
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
UV Photodiodes
Active area from 0.06 mm² to 36 mm² and quadrant photodiodes for position detections. Spectral response for broadband UV or filtered for UVA, UVB, UVC or UV-Index. Various entrance optics and housings options available (TO or SMD). Our own SiC photodiode chip production since 2009 also available with VUV sensitivity. PTB (German equivalent of NIST or NPL) measured high radiation hardness. 350°C high temperature stable photodiodes available. Photodiode application guide.
-
product
Seismometers
3T-360
A high-performance, observatory grade seismometer, suitable for monitoring the very long period with a 360 s to 50 Hz frequency response (option to 100 Hz)
-
product
Single Axis AC Magnetic Field Sensor
MGC-1A
Macintyre Electronic Design Associa
The MGC-1A is a low noise high sensitivity single axis AC magnetic field sensor used for the measurement of audio frequency fields. Because of its innovative design, the MGC-1A amplitude response is insensitive to the frequency of the field over its 30 Hz to 10 kHz frequency band. Accuracy at 1 kHz is ±1%, and the amplitude response stays within 2 dB peak-to-peak over the bandwidth.
-
product
Hydrophone
RESON TC 4038
The TC4038 is a miniature probe hydrophone, specifically designed as a standard reference hydrophone for high frequencies in the range: 100kHz to 1.2MHz. The TC4038 provides a flat frequency response and omnidirectional characteristics in the specified frequency range. The sensor element has excellent stability, which ensures reliable sensitivity over long periods of time.
-
product
Time-Domain Analysis
S95010B
Measure the time-domain response of a device; transform frequency-domain data to the time domain or time-domain data to the frequency domain
-
product
Low Noise Amplifiers
Our range of ITAR Free, Low Noise Amplifiers (LNAs) cover a variety of applications but are primarily suited to airborne, maritime and ground based radar systems. LNAs are primarily intended to minimise added noise whilst providing high gain so design focusses on the parameters associated with the noise response of the amplifier. They are usually the first amplifier in the Radar detection chain and will have the lowest noise figure.
-
product
Optical Delay
ODL
The Peregrine Optical Delay Line (ODL) provides an exceptional combination of precision, speed, and optical stability at a low price. It is ideally suited for pump-probe experiments and autocorrelation measurements (both interferometric and intensity methods). Advanced voice coil technology allows the ODL to be positioned anywhere in its travel range to within 150 nm. That’s 1 fs for a double-pass configuration. The response time is as short as 1 ms. Our 1-cm-travel ODL is interferometrically stable (measured using a 650 nm laser). No backlash, no hysteresis and no drive trains to wear out as with stepper motors. It’s convenient–the ODL can be positioned using digital commands, an analog voltage or a combination of the two. Two 16-bit on-board analog-to-digital converters simplify data collection. Digital inputs and outputs allow master or slave clocking. An executable Windows application is provided to get you up and running in minutes. In addition, DLLs and LabVIEW Vis for integration into your software are also included.
-
product
Phase Stable Cables
FlatPhase 100 Series
Best in class phase stability vs. temperature makes FlatPhase™ the preferred option when you need flat phase.Our proprietary foamed fluoropolymer dielectric avoids the typical PTFE knee to deliver a flatter phase response.
-
product
2-26.5 GHz GaAs MMIC Traveling Wave Amplifier
HMMC-5026
The HMMC-5026 is a broadband GaAs MMIC traveling wave amplifier designed for moderate gain and moderate output power over the full 2-26 GHz frequency range. Typical applications of the HMMC-5026 include wideband gain blocks of communication systems and microwave instrumentation, which require a flat gains response and excellent port matches over the 2-26 GHz frequency range.
-
product
Current Sensors
MCx1101 Family
Power architects are continually asked to push the boundaries for system efficiency, response time, small size, and low cost in new power system designs. Most modern designs require current sensors to help implement the complicated control, telemetry, and protection circuitry essential in meeting these difficult design goals.
-
product
IEPE Impact Hammers
Our range of general purpose IEPE impact hammers offer a range of great cost effective solutions for a majority of applications requiring the excitation of a structure. The most common application being Modal testing whereby the structure is excited using the impact hammer and the response of the structure is measured using accelerometers. However instrumented hammers can also be used for crack detection and other structure related investigations.
-
product
Radiation Detection
Radiation detectors for safety quality assurance is top of mind for hospitals, nuclear power facilities, nuclear medicine laboratories, x-ray manufacturers, government agencies, state inspectors, emergency response and HAZMAT teams, and police and fire departments around the world. Fluke Biomedical offers a complete line of radiation detection, personal dosimeters, staff radiation dosimeter monitoring, and safety products and solutions that allow these professionals the versatility they need to get the job done and the quality they trust in a radiation-safety device.
-
product
Gaussmeters
These gaussmeters are very good for Laboratory, Industry and field studies. They are made handy, sturdy and are capable of giving correct results under hostile conditions. As the inherent property of digital readout, the instrument has quick response to varying fields, good readability and good accuracy of measurement.
-
product
Vibration Meters
Simple to operate and are ideal for obtaining spot measurements. Features accurate, piezo-electric accelerometer sensor, LCD read-out in acceleration, velocity and displacement and true RMS velocity response.
-
product
Ocean and River Instruments
RINKO-FT (ARO-FT)
The RINKO FT not only retains the fast response time identical to that of conventional RINKO series but also has greater accuracy and stability by incorporating high-quality multipoint calibration and improved sensing method. This instrument is primarily designed to target Argo float operations,however, its compact, lightweight, and commonly used communication protocol widen the choice of platforms for installation. The RINKO FT allows DO measurements with a high vertical resolution, which will contribute to the understanding new aspects of physical/biochemical processes.
-
product
Ocean and River Instruments
RINKO III
Rinko III is an analog version with the fast optical DO sensor and a temperature sensor. With an external 12 DCV power, the instrument seamlessly outputs the analog data (0 to 5V) of the sensors. Rinko III can be easily integrated on various platforms with an Impulse cable. By the fast response, the instrument provides high accurate DO data without restricting profile speeds.
-
product
Gas Moisture & Sulfur Analyzers
Get fast responses and wide measurement ranges for reliable emissions monitoring. Our gas moisture and sulfur analyzers provide a solution for continuous and accurate determination of total sulfur in flare gas (high and low ranges), allowing sulfur emissions in process heaters and flares to be successfully monitored by petroleum refineries requiring compliance.
-
product
Process NIR Analyzers
Process near-infrared (NIR) analyzers continuously measure moisture, oil, coat weight and other parameters directly in manufacturing processes for responsive process control. Common industries include wood products, tobacco, snack foods, converting, and bulk materials. A variety of sample interfaces, environmentally rated enclosures, and interface options are available for easy implementation and integration.
-
product
AXIe High-Speed Digitizer/DAQ, 10-bit, 10 GS/s, DC to 2.5 GHz BW
M9710A
Based on the AXIe standard, the M9710A is a unique 10-bit high-speed digitizer, capturing signals from DC up to 2.5 GHz at 5 GS/s. It provides excellent measurement accuracy and high dynamic range across four phase-coherent channels within a single card. Optimized response allows few hundred picoseconds pulse analysis. Moreover, an interleaving option allows acquisition at 10 GS/s on two combined channels, keeping excellent measurement fidelity.
-
product
Diagnostic Testing
Response Dynamics Vibration Engineering, Inc.
Response Dynamics has made diagnostic testing our core focus for over 30 years. We do this detective work well because we have particular expertise in structural dynamics and how it relates to vibration and acoustic noise issues on a myriad of levels. We enjoy this work because it stays interesting and draws on multiple disciplines in engineering and science.
-
product
ICP Electret Array Microphone
130A23
Nominal Microphone Diameter: 1/4" Frequency Response Characteristic (at 0 incidence)Free-FieldInherent Noise (A Weighted)<30 dB(A) re 20 Pa<30 dB(A) re 20 Pa Dynamic Range (High)150Environmental Temperature Range ( Temperature Effect on Output (-10 to +50 C)<0.7 dB<0.7 dB[2] Influence of Axial Vibration Excitation Voltage 18 to 30 VDC18 to 30 VDC
-
product
Active Scanning Technology
ZEISS invented scanning in response to the drawbacks of single-point measurement nearly 50 years ago. This game-changing development enables the capture of thousands of data points within just a few seconds for truly reliable tactile quality assurance. It also saves time and money by delivering the high throughput and accurate results that are vital for manufacturing.
-
product
JTAG Boundary-Scan I/O Modules
SCANIO Family
The Corelis family of SCANIO™ modules turn any IEEE standard 1149.1 boundary-scan controller into a powerful digital boundary-scan tester. The SCANIO family of products use boundary-scan gate arrays to add control and visibility to connectors, traces, and logic that can not be tested using traditional boundary-scan techniques.The SCANIO products, when combined with a boundary-scan controller, operate as a traditional “bed-of-nails” tester except access to the stimulus and response I/O’s is achieved via boundary-scan.
-
product
Comparators
Renesas offers a comparator portfolio that includes nano power comparators, high-speed CMOS comparators, and precision quad comparators. Our general-purpose comparators utilize CMOS processes suitable for low voltage, low power consumption, and fast response. We have also recently expanded our comparator offerings with Intersil comparator products.
