Response
-
Product
Hardware Enabled SaaS Solution Quantifying Methane Emissions
MethaneTrack™
-
NevadaNano’s MethaneTrack™ is a low cost network of rugged monitoring points to measure methane emissions and report leak location and size to the operator. Utilizing an Industrial IoT (IIoT) network to detect methane in the air, MethaneTrack™ detects fugitive and operational emissions from a site and immediately alerts the operator of the location and volume of the emissions, facilitating rapid response and repair. Autonomous, continuous monitoring enables up to 99% reduction in emissions while reducing operational costs and boosting profits.
-
Product
Sensors
-
Seismic sensors provide a dynamic AC signal output in mV/g or mV/in/sec. Devices with this type of output are generally intended for connection to a stand-alone vibration monitoring system rather than general automation and control instrumentation like a PLC or DCS. Metrix offers seismic sensors with a wide variety operating temperatures, frequency responses, scale factors, case materials, connector types, mounting options, and hazardous area approvals.
-
Product
CAS Modbus Scanner
-
CAS Modbus Scanner is a utility to retrieve coils, inputs, holding registers, and input registers from a Modbus enabled device. Values retrieved from the device can be viewed in many different formats including Binary, HEX, Uint16, Int16, Uint32, Int32, and Float32. This utility can also discover Modbus devices on your network if you do not know their address. It works by testing every address, function, length, offset to check for exceptions or responses.
-
Product
Electronic Ballast Production Line Tester
UI2000-OK
-
• Eight windows for displaying input characteristics, output characteristics, convenient for comparison and analysis. • Frequency response for testing input current up to 1 MHz, suitable for precise testing of various kind of electronic ballast. • High speed testing, finish testing input and output characteristics within 1 minute. • Portable with built-in chip micro-processor, particular suitable for development and spot production. • Parameters, waves and curves of input, output and startup can be printed. • Communicating with PC, special software provided and both Chinese version and English version available. Run in WINDOWS3.2, WINDOW95 or WINDOWS98, nice interface between people and computer, easy to operate.
-
Product
PCI Programmable Resistor Card 4-Channel 2 Ohm To 510 Ohm
50-294-014
-
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Aerospace and Defense Software for the 4000 X-Series
D4000AERB
-
MIL-STD 1553 and ARINC 429 trigger and decode for the InfiniiVision 4000 X-Series oscilloscopes, along with mask testing, frequency response analysis, and video analysis
-
Product
Stereo Portable Digital Recorder
SPDR
-
The SPDR is Lectrosonics’ response to customer demand for a small, lightweight dual channel recorder for use on virtual reality sound captures or as a backup recorder for bag systems in the field. The SPDR will let you capture the full stereo audio of an extreme sport participant, in-car scenes or in situations where a wireless system cannot be used.
-
Product
High Speed Photoreceivers
-
Macom Technology Solutions Holdings Inc.
MACOM offers 40G and 50G amplified PIN photoreceivers with high responsivity PIN photodiodes usable from 1200 – 1650 nm. These products are available in butterfly packages with single-mode fiber and coaxial output connectors.
-
Product
Photometers & Colorimeters
-
Instrument Systems Optische Messtechnik GmbH
A photometer is used to measure the photometric quantities of illuminance (lx), luminous intensity (cd), luminous flux (lm), and luminance (cd/m²). The integral method and the fast response time of silicon photodiodes means that photometers can achieve an outstanding measuring speed. They are therefore ideal for performing fast goniophotometric measurements. We take great care in the development and production of photometer heads and use innovative amplifier technologies.
-
Product
Environmental Test Probe, Temperature
72-8364
-
Type K Surface Temperature Probe Surface probe is ideal for flat stationary surfaces such as molds, heating elements, integrated circuits, transistors and transformers. Very low sensor element mass enables fast response measurement time. Type K thermocouple temperature probes are commonly used with all types of industrial temperature controls and measurement equipment, and are compatible with Tenma handheld thermometers and digital multimeters that include temperature function. All are terminated with standard Type K plugs. See the complete line of Tenma Thermocouple Probes and Accessories
-
Product
Digital Circuit Breaker Analyzer
CT-3500 S2
-
The CT-3500 S2 is Vanguard’s second generation, stand-alone, digital, microprocessor-controlled, circuit-breaker timer. It measures the elapsed time from the instant a breaker coil is energized to the instant of opening or closing of a circuit-breaker’s dry contacts. In addition to timing a breaker’s contact response time, the CT-3500 S2 can also time relays or other switching functions that use an initiating trigger voltage (24-300 Volts DC or AC). The timer-triggering voltage starts three independent electronic timers. Each timer is individually stopped by its respective dry-contact closing or opening. The CT-3500 can fully analyze the timing of all circuit breaker operations (Open, Close, Open – Close, and Close – Open). Timing results are displayed in milli-seconds and cycles on the unit’s back-lit LCD screen and can be printed on the built-in 2.5-inch wide thermal printer.
-
Product
Ocean and River Instruments
RINKO EC (ARO-EC)
-
Aquatic eddy covariance method is a powerful technique to measure benthic fluxes. The robust RINKO EC (model name: ARO-EC), as a new member of the RINKO series, is designed for aquatic eddy covariance measurements. The RINKO series is based on the optical (phosphorescence) principle which is now widely known as a remarkably fast response oxygen sensor with high accuracy. The response time of the RINKO EC oxygen sensing foil is less than 0.5 s (90%, from air to water at 25 °C). The foil life-time is more than 200 h, which enables at least 1 week of continuous measurements of dissolved oxygen. Moreover, the foil can be replaced easily by the user. Berg et al. (2016)*, after a detailed evaluation, concluded that RINKO EC is a reliable alternative for aquatic eddy covariance measurements of oxygen fluxes and its high data quality allows for new opportunities for eddy covariance flux studies, including long-term deployments in rivers, streams, and marine environments.
-
Product
Telecomm Services
-
Advanced Technical Enterprises, Inc
The UNIVERGE SV8000 Series Communication Servers from NEC creates new ways of generating revenue and increasing customer responsiveness while simultaneously improving efficiency and reducing costs. This robust, feature-rich solution is completely scalable and can be expanded to meet your communications needs both now and in the future. Designed to be both versatile and scalable for your growing business needs, the SV8100 supports TDM, IP, video, wired or wireless.
-
Product
Type 2, PCMCIA Dual Redundant MIL-STD-1553 serial bus Simulator Analyzer Tester
PC401
-
MIL-STD-1553 A, B, & McAir MULTI PROTOCOLS Simulator/Analyzer/Tester type 2 PCMCIA BUS Interface Card - The PC401 can be used for Validation Testing, ProductionTesting, full bus simulation and monitoring, as a generalpurpose 1553 interface or a stand alone bus Analyzer. Forprecise message scheduling and measurements, the Majorand minor frame times are independent of messagesequences or retransmissions on errors and the start of allcommand messages are independent of message length,response time or length of response. Message timing iscalibrated and RT responses have low jitter.
-
Product
Fast Response Flow Controller for Low Flow
HFM-300 / HFC-302
-
The all metal HFM-300/HFC-302 is Teledyne Hastings' metal sealed, fast response series of mass flow meters and controllers. Featuring reliability and stability, the 300 Series is chosen by OEM's for its fast response under a wide range of conditions.The HFM-300 / HFC-302 meters and controllers have flow ranges from 0-5 sccm to flows of 0-25 slm; provide analog outputs, are constructed of stainless steel and have normally closed valves. The full scale range is specified by the end user. A NIST traceable calibration certificate is standard. Corrosive gases and pressures up to 1000 psig are easily measured. Cleaning for oxygen service is available.
-
Product
Electrical Components Testing
-
To be successful on the market, the safety, quality, durability, and reliability of your products are essential.Manufacturers are responsible for ensuring that the products they place on the market meet all relevant regulations. Ensuring that your customers receive safe components of high quality is critical to the longevity of your business.Every part of an electrical appliance can be hazardous and one defective component can lead to disastrous results. Our experience and scope of accreditations help you to meet local and global electrical product safety regulations. As one of the largest certifiers within the CB Scheme TÜV Rheinland Group has vast experience in a broad range of product testing.
-
Product
Security/Detection
ST60 Dual
-
A two-channel silicon-based thermopile detector in a TO-5 package. Each small active area size is 0.61mm x 0.61mm. This is our lowest-cost and fastest time constant two-channel detector. It delivers a time constant of 18ms with Nitrogen encapsulation gas combined with a very low Temperature Coefficient of Responsivity of -0.04%/°C. This detector has a very short thermal shock response to ambient temperature change.
-
Product
RWR ATE MKII
MS 1111
-
Automatic Test Equipment (ATE) MKII is a customized tester, built to carry out LRU and card level testing for TARANG systems of all platforms. The purpose of ATE is to provide a user-friendly environment to test the LRUs and sub-systems (individually) for their functionality, perform specific tests of each LRU / sub-system and Card Level Testing. The card level testing facilitates troubleshooting down to a faulty signal flow path. The UUT tests are carried out by injection of the stimuli generated by the computer or the programmable test equipments and the responses from UUT / test equipments are feedback to the computer for evaluation and generation of reports.
-
Product
PXI Programmable Resistor Card 2-Channel 2.5 Ohm to 8.19k Ohm - SPST
40-294-124
-
These PXI Programmable Resistor modules are available with either two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Light Measurement Input Optics
-
International Light Technologies
Light measurement units are defined around very specific spatial responses. A carefully designed input optics system is essential if measurement accuracy is to be achieved.
-
Product
Fast and Flexible WLAN Measurements up to 802.11ax
WLAN Test Toolkit
-
The WLAN Test Toolkit gives you direct and fine control over the generation and analysis of IEEE 802.11a/b/g/n/ac and ax signals, as well as 802.11j/p/ah/af waveforms, with industry-leading speed and accuracy. It empowers you to characterize, validate, and test a variety of WLAN connectivity products, such as RF front end components, wireless modules, and user devices.The toolkit includes extensive support for the latest features of the 802.11ax standard, including extended single-user packets, multiuser OFDMA, and multiuser multiple input, multiple output (MIMO) functionality with per-user configuration and measurement results. The WLAN Test Toolkit helps you solve demanding new access point test cases by generating signals that simulate multiuser environments, including per-user impairments. You can also use the new software to generate trigger frames to test the real-time response of client devices and make power precorrection and relative center frequency measurements.
-
Product
Linearizers
-
Gain Shape Linearizer Amplifiers are used in a number of applications where it's necessary to flatten the gain characteristic of the preceding or following component. This would include flattening the attenuation of a long cable run, or perhaps changing the input gain response to a MPM (Microwave Power Module) or TWT (Traveling Wave Tube) to compensate for the gain variation within the tube.
-
Product
Vector Network Analyzer
Bode 100
-
With the multifunctional Bode 100 you get an exact picture of your electronic circuits and components in a frequency range from 1 Hz to 40 MHz. The Bode 100 is not only a state of the art Vector Network Analyzer, it also works as: Frequency Response Analyzer, Impedance Meter, Gain Phase Meter, Sine Wave Generator.
-
Product
Cryogenic Hygrometer
CR - 2
-
Buck Research Instruments, LLC
The CR-2 exhibits the same wide range, fast response and high reliability as the CR-1A, but it is designed specifically for aircraft and similar high-stress applications. Instead of using Liquid Nitrogen (LN2), mirror cooling is accomplished using a tactical cryocooler, which is a high-tech device used primarily to cool IR detectors in missiles and tank turrets to LN2 temperatures.
-
Product
FCC TCB Services
-
As a TCB, we perform the evaluation of testing for radio and telephone equipment that was previously the sole responsibility of the FCC. Eurofins is authorized to issue Grants of Equipment Authorization for any equipment for which there is a defined rule part and procedure within Title 47 of the Code of Federal Regulations. Following the issuance of this grant, the grantee will be free to begin marketing the device in the United States.
-
Product
Spiral Antenna
-
UHF Spiral antenna is a partial discharge sensor designed to receive electromagnetic (EM) emissions from a PD occurring in the monitored asset. It is a broadband antenna with a flat response which makes Spiral antenna suitable in a number of different applications. It has been optimized to operate in a frequency range typical for PD activity and it was designed to provide maximum sensitivity and high gain.
-
Product
Environmental Vibration Testing
-
Whether for independent monitoring or just adding additional channels to an existing vibration controller, the m+p Analyzer real time analyzer provides an ideal solution for measuring vibration and other responses during a shaker test or with shock machines. All test modes allow in-parallel throughput to disk recording so that the raw sample data is available for post-test analysis.
-
Product
Frequency to Voltage Converters
-
Encore Electronics offers a complete line of frequency to voltage converters ranging from the economically priced and compact DIN rail mounted Model FL228 to the rack mounted Model 225. For applications requiring performance between these two models, we now offer our FL236 DIN-rail packaged Digital Frequency/Voltage converter, featuring fast response time, low power and compact footprint.
-
Product
Vibration Meters
-
Simple to operate and are ideal for obtaining spot measurements. Features accurate, piezo-electric accelerometer sensor, LCD read-out in acceleration, velocity and displacement and true RMS velocity response.
-
Product
Multispectral Fixed Camera for Early Fire Detection
FH-Series R
-
The FLIR FH-Series R are ruggedized, multispectral fixed cameras that integrate industry-leading thermal imaging with 4K visible imaging to provide rapid visual verification of hot spots in early fire detection applications. When a hot spot or temperature change is detected, the contactless temperature measurement is sent to the operator through a connected Video Management System (VMS) for instantaneous assessment and deployment of response tactics. Custom scheduling provides security personnel the flexibility to enable and disable alarms depending on business hours and seasonality. Combining the power of thermal hot-spot detection with intelligent vehicle detection, false alarms from hot exhaust pipes can be dramatically reduced.
