Jumpers
-
Product
8 Channel Sample & Hold and Signal Conditioning Board for Group3
-
All channels provide for voltage division ahead of transient suppression before going into the S&H ICs. Channels that are sampled and held use a common sample and hold pulse that samples while high and holds while low. Jumpers on each S&H chip allow buffering of analog signals where sample and holds are not required. An advantage to the buffers is that it provides a high input impedance for high impedance voltage dividers.
-
Product
I/O Input/Output Board
VME-4514A
-
The VME-4514A Analog I/O (AIO) Board provides 16 high-quality analog output channels which can be programmed with on-board jumpers to operate in a variety of voltage ranges. Each output can source or sink 10 mA at ±10 V. For off-line testing, the analog outputs can be disconnected from the I/O connector.
-
Product
USB Tester 2.0
TLS-0050
-
The USB Tester will make it a snap to monitor voltage levels and current usage without having to re-wire your breadboard. Just connect to your oscilloscope or DMM test leads, and you're good to go! The USB Tester has both banana clip sized drills and standard 0.1" headers. When you are not testing current you can add a jumper for normal operation. The USB D+/D- pins are also broken out so you can monitor those on an oscilloscope, or for USB sniffing.
-
Product
Deluxe Relay Test Set
60660
-
Jumpers have tabs for clamping and flat pads to place test leads on. No need to pierce wires or connect multiple jumper wires. Also Includes Test Lead Kit for easily and securely connecting Relay Test Jumpers to a multimeter. Jumper wire may be used between common and open to close the relay circuit for testing and has a test port to easily check voltage. Also provides access for a clamp-on amp meter. Relay Puller Pliers easily remove electrical relays without damage to the relay or electrical box.
-
Product
Mini-Link™ Miniature Jumper
Series ML-100
-
Mini-Link Miniature Jumpers. Used to jumper from row-to-row or from pin-to-pin. Their miniature size makes it possible to stack one on top of the other. A convenient test probe slot is provided as well. Mini-Links are available from the factory with or without a handle, used for ease of inserting or extracting.
-
Product
Load Cell Amplifier Signal Conditioner with Removeable Terminals
MODEL LCA-RTC
-
The LCA-RTC Module provide low-cost, dedicated signal conditioning for a single bridge type load cell or torque sensor. Model LCA-RTC comes with removable screw-clamp terminal connectors, which accept wires without soldering.On- board jumper selections include sensitivities from 0.5 mV/V to 10 mV/V, bandwidths from 100 Hz to 30 kHz, and amplified outputs of 0 to ±5V, 0 to ±10V, 0-16 mA, 0-20 mA or 4-20 mA. Zero and span adjustments are via precision 25-turn low-tempco metal film potentiometers.The units can be operated next to the sensor with 4-wire hookup or at distances up to 1 km (3300 feet) with 6-wire hookup. An onboard 87.325 kΩ resistor allows easy shunt calibration at the push of a button. Provision is also made for a user-furnished calibration resistor. Power requirements are 11.8 to 26V DC with load currents from 10 to 60 mA, the latter applying when the unit provides 10V DC excitation to a 350 ohm load cell and delivers a 20 mA analog output.
-
Product
Terminals And Test Points
-
Today's high tech electronics require space saving, low cost methods for connecting and testing circuitry. Our complete line of Quick Fit terminals, Screw Terminals, Solder Lugs and Test Points and Jumpers are designed to meet the interconnect and testing challenges for electronic and electrical component termination points.
-
Product
Digital Display for the Transducers and Transmitters
PS57
-
The PS57 is a combination power supply and 4 1/2 digit LED display for the P55/P855 family of pressure transducers and transmitters. The PS57 accepts 110 VAC power and provides the required 24 Vdc excitation for the transducer. The transducer signal is received and displayed directly in engineering units with bright 0.56 high red LEDs. The user can re-scale the display and set the decimal point by configuring internal jumpers. The analog output of the transducer, 5 Vdc or 4-20 mA, is available on rear-panel terminals.
-
Product
Length Network Cable Tester
SC-8108
-
1. Measure network cable length and determine the distance of breakage point.2. Check wiring error in 5E, 6E, coaxial cable, such as open circuit,short circuit, jumper wire, reverse connection .3. Portable unit with long battery life (wait-case 50 hours).4. Automatically time-delay shut off.5. Self-checking and automatically compensate any change in battery capacity or ambient temperature.
-
Product
PXI Dual 0-30VDC Programmable Power Supply
TE3200
-
The TE3200 is a dual output programmable DC power supply designed for use in PXI/CompactPCI chassis. The TE3200 occupies a single slot and will utilize an external supply of 48VDC (provided). A separate srrew-terminal/power adapter board, p/n TE3202, provides connectivity for two 48VDC power suppies and screw-terminals and jumpers for voltage and sense selection and connection. The TE3202 is included with all retail purchases (not included with OEM purchases).
-
Product
SparkFun Digital Temperature Sensor Breakout
AS6212 (Qwiic)
-
This SparkFun Qwiic Digital Temperature Sensor Breakout provides a combination of high temperature accuracy with excellent low power consumption using the AS6212 digital temperature sensor from ams AG. The sensor measures temperature data up to ±0.2°C; accuracy over a wide range (-40°C; to +125°C;) and consumes an average of 6µA in normal operation (0.1µA in standby). The AS6212 communicates via I2C and has eight available I2C addresses selected by a pair of solder jumpers on the board. The breakout routes the I2C interface to a pair of Qwiic connectors to work with our plug-and-play Qwiic Ecosystem but also routes the bus and other pins to a standard 0.1"-spaced PTH header for users who prefer a soldered connection.
-
Product
CPCI or PXI Digital IO Board
MS 1802
-
*Bus Interface - PCI Bus*Number of Channels 198*Compatibility - TTL*Power on state - Inputs (high-Z), pulled up or down (jumper selectable)*Handshaking - Input, Output, or bi-directional*Data transfers - Interrupts, programmed I/O*Driver interface for Windows2000/XP/VISTA and LINUX OS
-
Product
Pulse Initialization Demo Board
TMR9112
-
MultiDimension Technology Co.,Ltd.
The TMR9112 demo board was developed to support evalution of the TMR9112 single-axis sensor. The demo board comes with the fast bipolar current pulsing circuit needed for initialising the TMR9112 sensor, and it can be powered from a USB port or any external 5V power supply. For user convenience, the demo board has an optional on-board timer clock with four selectable frequency settings. The On-board timer clock and frequency output can be enabled using the jumper pins. This demo board is divisable along the dotted line so that the sensor board can be seperated from the pulsing circuit board.
-
Product
Economy Model Vertisocket™
Series 800 and 822
-
Thrifty Model Vertisockets with Bifurcated Contacts. These low cost VertisocketsTM are recommended for high volume vertical display mounting applications. Very useful for connection of board-to-board jumpers and for DIP switches as well as LED devices.
