Analog Input
measurable voltage value.received from a sensor.
-
Product
16-Channel 500kSa/s USB Modular Multifunction Data Acquisition
U2353A
Data Acquisition Module
The U2353A offers multifunction capabilities in a module. It can be used like a digital multimeter in polling mode. It can be transformed to be a simple scope using the continuous mode with simple triggering capabilities. No matter if it is used as a standalone module or when plugged into a U2781A USB modular instrument chassis, the synchronization and triggering capabilities allow great flexibility in making the desired measurements. With the analog output being able to send out predefined or arbitrary waveforms make this a good tool when closed loop feedback or stimulus is required. The digital IO channels allows for closed loop control through connections to switches, relays and solenoids. The burst mode enables the U2353A to simulate simultaneous analog input acquisition.
-
Product
Configurable CAN FD Module With A Focus On Analog I/Os
PCAN MicroMod FD Analog 1
-
The PCAN-MicroMod FD breadboard can be purchased together with ready-to-use motherboards that provide peripherals for specific requirements. Spring clamp connectors are used to connect CAN, I/O and supply. The motherboard PCAN-MicroMod FD Analog 1 focuses on analog inputs and outputs, which are provided with the appropriate protective circuit.
-
Product
NI-9223, ±10 V, 1 MS/s, 16-Bit, Simultaneous Input, 4-Channel C Series Voltage Input Module
781398-01
Voltage Input Module
±10 V, 1 MS/s, 16-Bit, Simultaneous Input, 4-Channel C Series Voltage Input Module - The NI‑9223 performs differential analog input. This module is well suited for applications such as ballistics, impact, and blast wave testing. The NI‑9223 can sample at the maximum sample rate per channel while the module next to it samples at a much slower rate, which is ideal for mixed-measurement test systems. There are two connector options for the NI‑9223: either four, 2‑position screw terminal connectors or four BNC connectors.
-
Product
Multifunction Analog I/O Card
LPCI-AIO16A
-
Model LPCI-AIO16A provides 500k samples/second, with 16-bit resolution, for the board’s 16 single-ended or 8 differential analog input channels. Also included are two 12-bit analog outputs, 16 digital I/O lines and an 8254 with three 16-bit counter/timers. The board meets the MD2 Low Profile PCI Bus Specification and can be installed in any 3.3V or 5V PCI or PCI-X slot.
-
Product
Measurement and Analytics Solutions
-
Based on our OTP² system platform, we were able to implement a family of scalable test systems which is based on a common systems architecture, e. g. for products in the area of chemical analytics measurement. We not only implemented a universal, extremely comprehensive test system, but also a series of compact systems for benchtop placement which are fully compatible with the larger, universal system. Our specialized self-test adapters and test software enable fast verification of the test systems as well as partly automated calibration by the customer.Our systems are also used in electrical measurement applications, e. g. for calibrating analog input assemblies for PLC technology. For this purpose, specialized calibrators are integrated into the system; they provide traceable calibration of the relevant stimulus signals.
-
Product
Peripheral Port Expander
-
The Peripheral Port Expander (PPE) is a connection box with 32 banana sockets (4mm) for easy connection to the various analog and digital inputs&outputs that are available in each Ivium potentiostat. The banana sockets are colour coded for easy recognition and include a5 V, max. 100 mA power point. A DB37-data cable connects the PPE to the potentiostat.
-
Product
NI-9209 , ±10 V, 500 S/s, 16-Channel C Series Voltage Input Module
785042-01
Voltage Input Module
±10 V, 500 S/s, 16-Channel C Series Voltage Input Module - The NI‑9209 performs single-ended or differential analog input. This module provides 60 VDC CAT I isolation and built-in 50/60 Hz filtering, making it a valuable addition to industrial measurement systems.
-
Product
NI-9237, 50 kS/s/channel, Bridge Analog Input, 4-Channel C Series Strain/Bridge Input Module
780264-01
Strain/Bridge Input Module
50 kS/s/channel, Bridge Analog Input, 4-Channel C Series Strain/Bridge Input Module - The NI‑9237 includes all the signal conditioning required to power and measure up to four bridge-based sensors simultaneously. The module provides strain or load measurements with zero interchannel phase delay. It also has 60 VDC isolation and 1,000 Vrms transient isolation, providing high‑common‑mode noise rejection and increased safety. You can program the NI‑9237 for use with half-bridge and full-bridge sensors with built-in excitation. The four RJ50 jacks provide direct connectivity to most torque or load cells and offer custom cable solutions with minimal tools.
-
Product
Analog And Digital Sensor Measurement Data For CAN Applications.
K- AN8 KIT
-
This K-AN8 (8 analog + 4 digital input) kit contains everything needed to get the K-AN8 set up and tested on a work bench.To help with connecting sensors to the analog and digital ports the K-BoB enables easy connection with BNC connectors.Influx K-Cal is easily connected via the Kvaser LeafLight interface and Kvaser T-CANnector. (Using the Kvaser T-CANnector to power up the K-AN8 (at the desk) and terminate the CAN bus).
-
Product
GSM Controller
SCOM-100
-
Infinite Industrial Informatics Lt
SCOM-100 is a powerful GSM controller for alerting and remote control using SMS. The rail mount unit incorporates a Quad Band GSM/GPRS modem, 2 analog inputs, 4 digital inputs with retentive pulse counting capability, 4 power relay outputs and a serial RS-232 port.
-
Product
sbRIO-9221, Non-Enclosed, ±60 V, 800 kS/s, 12-Bit, 8-Channel C Series Voltage Input Module
781116-01
Voltage Input Module
Non-Enclosed, ±60 V, 800 kS/s, 12-Bit, 8-Channel C Series Voltage Input Module - The sbRIO‑9221 performs single-ended analog input. The wider voltage range makes this module well suited for industrial-level, automotive, or even smaller-cell battery measurements. There are two connector options for the sbRIO‑9221: a 36‑position spring‑terminal connector and a 37‑position DSUB connector. Non-enclosed modules are designed for OEM applications.
-
Product
PXIe-5764, 16-Bit, 1 GS/s, 4-Channel PXI FlexRIO Digitizer
785167-01
FlexRio Digitizer
The PXIe-5764 is a PXI FlexRIO Digitizer that simultaneously samples four channels at 1 GS/s with 16 bits of resolution and features 400 MHz of analog input bandwidth. With up to 70 dB of SNR, the PXIe-5764 is ideal for applications that require a wide dynamic range with a wideband digitizer. The FlexRIO driver includes support for finite and continuous streaming modes, and you can implement custom algorithms and real-time signal processing on the LabVIEW-programmable Xilinx Kintex UltraScale FPGA. Available in AC and DC coupled variants, the PXIe-5764 is ideal for both time and frequency domain applications, including radar prototyping, LIDAR, communications, microscopy, OCT, event detection, and particle physics.
-
Product
PCI-Express, 16 SE/8 DIFF Analog Inputs, 8 Analog Outputs,16-bit, 8 Digital I/O, 24 V
APCIE-3021-16-3
-
The PCI-Express analog input/output board APCIe-3121 has 16 SE/differential inputs, 8 analog outputs, 16-bit, and 8 digital I/O, 24 V. The board is especially suited for applications in industrial process control, measurement technology and monitoring, for example for multichannel data acquisition, for the control of chemical processes, for the acquisition of sensor data, current measurement etc. in the harsh industrial environment.
-
Product
PXIe-7866, Kintex-7 325T FPGA, 24-Channel AO, 1 MS/s, PXI Multifunction Reconfigurable I/O Module
787354-01
Multifunction Reconfigurable I/O
PXIe, Kintex-7 325T FPGA, 24-Channel AO, 1 MS/s, PXI Multifunction Reconfigurable I/O Module - The PXIe-7866 features flexibility of timing and synchronization with a user-programmable FPGA for onboard processing and direct control over I/O signals. The PXIe-7866 provides 24 analog output, 2 analog input, and 32, 5V input-tolerant digital I/O channels connected to a Kintex-7 325T FPGA to help you design applications for hardware-in-the-loop testing, custom protocol communication, sensor simulation, and high-speed control. You can use the dedicated A/D converter (ADC) for independent timing, individual channel triggering, and multirate sampling. Additionally, the PXIe-7866 includes peer-to-peer streaming for direct data transfer to other PXI Express modules.
-
Product
SparkFun Triple Axis Accelerometer Breakout
LIS3DH
-
The LIS3DH Breakout is a smart, low-power, three-axis, capacitive micro-machined accelerometer with 12 bits of resolution that you can use to add translation detection to your project. It would be classified as a 3DoF, or 3 Degrees of Freedom. Inertial Measurement Units (or IMUs) can provide additional space location data, such as gyroscopic or magnetometric. The LIS3DH provided on this breakout operates under the same principles but gives a few analog inputs to play with, and it has some built-in movement detection abilities.
-
Product
Dual 2.0 Gsps. 12 Bit ADC FMC
ADF-D2000
-
This FPGA Mezzanine Card (FMC) converts two channels of up to 2.8GHz analog input bandwidth at 1.0, 1.6, 1.8, or 2.0 Gsps and 12-bit resolution. Additionally, this FMC can be used in an interleaved mode to convert a single channel at 2.0, 3.2, 3.6, or 4.0 Gsps and 12-bit resolution. Based on the VITA 57 specification, the ADF-D1600 enables direct coupling of unparalleled analog-digital conversion capability with the VME/VXS/AMC/VPX/PCI-E carrier board of your choice. DEG engineers have designed this product and associated HDL firmware to work with both Altera and AMD FPGAs.
-
Product
3-in-1 Analyzer: Logic Analyzer, Protocol Analyzer, Simple DSO
MSO2216B+
-
3-in-1 Analyzer : Logic Analyzer, Protocol Analyzer, Simple DSO• PC-based, USB3.0 interface• 8 / 16 Channels(display digital and analog waveforms of the same channel)• Digital Inputs : 2 GHz Timing, 200MHz State Analysis (Max.)• Analog Inputs : 200 MS/s (Max.), Bandwidth 40 MHz• 8 Gb Memory (Max.)• PC RAM storage for streaming mode• Utility model patent of Taiwan number M601827
-
Product
PCI-6111, 2 AI (12-Bit, 5 MS/s/ch), 2 AO, 8 DIO, PCI Multifunction I/O Device Multifunction I/O Device
777530-01
Multifunction I/O
2 AI (12-Bit, 5 MS/s/ch), 2 AO, 8 DIO, PCI Multifunction I/O Device - The PCI‑6111 is a simultaneous-sampling, multifunction DAQ device. It offers analog I/O, digital I/O, two 24‑bit counters, and digital triggering. The PCI‑6111 is ideal for a variety of applications, such as … stimulus/response applications that require synchronization among analog input (AI), analog output (AO), and digital I/O. It is also ideal for 42 V automotive applications, radar, sonar, and ultrasound. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements. The PCI‑6111 dimensions require chassis slots that can accommodate full-length PCI modules.
-
Product
Modbus Analog Output Modules
DAT3020 Series
-
The DAT3020 series from Datexel is a range of Modbus analog output cards. These cards or modules have both voltage and current outputs either 0-10V or 4-20mA and are isolated from the input, output and power supply. They are available with either 2, 4 or 8 channels. The DAT3011 is a Modbus slave with 2 analog inputs (Thermocouple, RTD's mA, Resistance, Potentiometers, mV and voltage) and 2 analog outputs(4-20mA). It also has 3 digital inputs and outputs. Combining these analog output cards with the analog input cards, and the digital IO cards with the DAT9000 controllers make Datexel the smart choice where Data Acquisition is needed.
-
Product
Multifunctional I/O Module
DP-OBC-1122
-
DP-OBC-1122 is a standard 3U cPCI Multi-Functional IO module. This board operates on 32bit, 33MHz PCI bus. The key function of the module is to provide analog IO interface, in addition to the various communication interfaces such as ARINC429, RS422 and Rs232.It has an ADC, operating with ±10V analog input catering for 8 single ended / 4 differential ended channels and a DAC which provides 4 channels of analog signals with a maximum output voltage of ±10V .The module also features standard communication channels and general purpose IOs.
-
Product
NI-9225, 300 Vrms, 50 kS/s/ch, 24-Bit, Simultaneous Input, 3-Channel C Series Voltage Input Module
780159-01
Voltage Input Module
300 Vrms, 50 kS/s/ch, 24-Bit, Simultaneous Input, 3-Channel C Series Voltage Input Module - The NI‑9225 performs differential analog input. The wide measurement range is well suited for high-voltage measurement applications such as power metering, power quality monitoring, motor test, battery stack testing, and fuel cell tests. You can perform transient and harmonic analysis with high-speed simultaneous sampling. In addition, you can prevent ground loops and add safety to a system with 600 Vrms channel‑to‑channel isolation between the three NI‑9225 channels.
-
Product
NI-9206, ±10 V, 250 kS/s, 16-Bit, 32-Channel, 60 VDC Isolation C Series Voltage Input Module
779526-01
Voltage Input Module
±10 V, 250 kS/s, 16-Bit, 32-Channel, 60 VDC Isolation C Series Voltage Input Module - The NI‑9206 performs differential analog input with four programmable input ranges. The module provides up to 600 VDC (400 VDC in Europe) channel‑to‑earth ground isolation, making the module ideal for accurately monitoring large fuel cell and battery stacks. By referencing the module common (COM) to the middle of the NI‑9206 bank, you can measure 16 consecutive cells and remain within 10 V of the module COM.
-
Product
Industrial-Grade Intelligent Analog & Digital Interface Modular Control Box With Arduino Compatibility
I-Pi OT2IT
Interface Module
Discover the freedom of open-source innovation with ADLINK's industrial-grade I-Pi Arduino-Compatible PLC. Say goodbye to restrictive proprietary systems and embrace the vast, versatile world of the Arduino ecosystem. Accelerate your project's journey from concept to commercialization across diverse automation and control tasks. All this, while ensuring steadfast reliability, professional-grade functionality and industry-ready performance.I-Pi-OT2IT is equipped with numerous analog and digital sensors to manage different OT devices in smart factories. It features 8x Digital inputs, 11x Digital outputs, 9x Analog inputs, and 2x Analog outputs, and can be easily controlled by Computer-on-Modules via software over Ethernet/LAN. By consolidating OT with IT, it is the ideal solution to transform your factory into a smart one.
-
Product
NI-9237, 50 kS/s/channel, Bridge Analog Input, 4-Channel C Series Strain/Bridge Input Module
780264-02
Strain/Bridge Input Module
50 kS/s/channel, Bridge Analog Input, 4-Channel C Series Strain/Bridge Input Module - The NI‑9237 includes all the signal conditioning required to power and measure up to four bridge-based sensors simultaneously. The module provides strain or load measurements with zero interchannel phase delay. It also has 60 VDC isolation and 1,000 Vrms transient isolation, providing high‑common‑mode noise rejection and increased safety. You can program the NI‑9237 for use with half-bridge and full-bridge sensors with built-in excitation. The four RJ50 jacks provide direct connectivity to most torque or load cells and offer custom cable solutions with minimal tools.
-
Product
cDAQ Modules
-
More than 50 input / output modules for various measuring tasks - analog and digital input / output, tensometry, vibroacoustic diagnostics, temperature measurements, control of external devices and telecommunications.
-
Product
High Speed Data Acquisition Module
ADQ214
Data Acquisition Module
The ADQ 214 data acquisition card features dual channels, 14-bit resolution, 400 MSPS capture rate with 1.4 GHz analog input bandwidth, and a memory buff er of 64 MSample per channel. The combination of high speed, high resolution and wide bandwidth makes it ideal for broadband applications such as IF sampling of RF signals and high-speed data recording. PXI Express, USB interfaces.
-
Product
Isolated Process Control Signal Conditioning Products
SCIM7B
-
SCIM7B Isolated Process Control Signal Conditioning Modules provide a complete selection of backpanels DIN rail mounting accessories, interface cables and rack mounting hardware.Each SCIM7B module provides a single of isolated analog input or output. Various input modules accept analog voltage or current signals from all types of field sensors and sources, filter, isolateamplify, linearize and convert these input signals to high-level analog outputs suitable for use in a process control system. Output modules accept high-level analog voltage signals from a process control system, then buffer, isolate, filter, convert and amplify before providing a current or voltage output to a fielddevice.
-
Product
Load Cell Transmitter
MODEL SST-HV
-
The SST-HV is a Plug & Play Smart TEDS IEEE 1451.4 compliant Transmitter. Just plug in a TEDS compatible Load Cell or Torque Sensor and the SST-HV will automatically self-calibrate. When used with a non-TEDS Load Cell or Torque Sensor, the SST-LV Transmitter is easily programmed using a PC with an RS232 port and Instrument Setup (IS) software, which provides a graphical user interface. The SST-HV may be powered from 95-240 Vac ±10%. The SST-HV has an Isolated transducer excitation output that is selectable between 5Vdc or 10Vdc. There are Dual solid state relays and an Isolated 4-20 mA, 0-20 mA or 0-10V analog output. There are three Isolated serial data transmitter output ( RS232 , Half-duplex RS485, full-duplex RS485 ) and three serial protocols that are software selectable (Modbus RTU, Modbus ASCII and Custom ASCII). Isolation to 250V rms is provided for power, signal input, analog output, relay outputs, and communications. Isolation adds safety and avoids possible ground loops. The transducer excitation output is isolated to 50V from signal ground.
-
Product
GPIB Analog Interface
Model 4861B
-
ICS's GPIB to Analog Interfaces are designed to provide isolated analog and digital drive signals to control power supplies and other devices. Optional isolated Analog inputs. Available in rack mountable Miniboxes™ and OEM board versions. All of ICS's GPIB to Analog Interfaces are fully IEEE-488.2 compliant and HP-IB compatible.
-
Product
NI-9244, 400 Vrms L-N, 800 Vrms L-L, 50 kS/s/ch, 24-Bit, 3-Phase C Series Voltage Input Module
783106-01
Voltage Input Module
400 Vrms L-N, 800 Vrms L-L, 50 kS/s/ch, 24-Bit, 3-Phase C Series Voltage Input Module - The NI‑9244 performs single-ended analog input. The wide measurement range makes it ideal for high-voltage measurement applications such as phasor measurements, power metering, power quality monitoring, industrial machinery, and motor test. You can also perform transient and harmonic analysis with high-speed simultaneous sampling. The NI‑9244 offers three channels, so you can connect single‑ or three‑phase measurement configurations such as WYE and delta. You can incorporate the NI‑9244 into systems to meet standards such as IEC 61010‑1, C37.90 and C37.60, IEC 60255‑22‑(1:7), IEC 60255‑1, C37.188 Class M and P, EMC section of IEC 60870, EMC sections of IEC 61850, IEC 61000‑4‑30 Class S, and IEC 61000‑4‑7.
