Digital Signal Processor
A microprocessor specifically intended for digital signal processing applications, generally in real-time.
-
product
PXIe-5663E, 6.6 GHz PXI Vector Signal Analyzer
781339-02
6.6 GHz PXI Vector Signal Analyzer - The PXIe‑5663E offers wide instantaneous bandwidth and supports RF list mode, which increases multiband measurement speed with fast and deterministic changes in configuration. You can use a PXIe‑5663E as either a spectrum analyzer or vector signal analyzer, and you can use it with the Modulation Toolkit to analyze custom and standard modulation formats. The PXIe‑5663E can perform measurements for a broad range of communications standards such as GSM, EDGE, WCDMA, WiMAX, LTE, Bluetooth, WLAN, DVB‑C/H/T, ATSC, and MediaFLO. Because all measurements are software defined, you can reconfigure the measurements using standard-specific toolkits. With these toolkits, the PXIe‑5663E provides a low-cost solution to high-performance RF measurements.The PXIe-5663E comprises the following modules:• PXIe-5601 RF Signal Downconverter• PXIe-5622 IF Digitizer• PXIe-5652 RF Analog Signal GeneratorThere is no physical device named "PXIe-5663E".
-
product
Multifunctional Digital Design Core
PA72DIOS6016
The PA72DIOS6016 is a multifunctional digital design core. The FPGA allows for implementing many different custom applications. The connector has 64 Input/Output pins which can be assigned as TTL I/O or as differential inputs. 128 MByte of DDR2 memory is available to the FPGA, and an onboard EEPROM allows for storing values in non-volatile memory. The I/O bank voltage can be FPGA-selected between 2.5 and 3.3 Volt.
-
product
PSG Vector Signal Generator, 100 kHz to 44 GHz
E8267D
Test advanced receivers with realistic wideband radar, EW and Satcom waveforms with metrology-grade performance and versatile capabilitiesSimulate complex electromagnetic environments with up to 4 GHz of bandwidthReduce the time you spend creating complex signals with Signal Studio software: pulse building, noise power ratio (NPR), multi-tone signals, wireless & moreMaster your most complex signal requirements with the industry's best SSB phase noise: 143 dBc/Hz at 1 GHz (10 kHz offset)
-
product
8-CH 14-bit 100 MS/s High-Speed PXI Express Digitizer
PXIe-9848
The ADLINK PXIe-9848/9848H is an 8-channel, 14-bit, 100 MS/s digitizer delivering both high-accuracy measurement results and high-dynamic performance. With a PXI Express bus interface and ample onboard acquisition memory up to 512 MB, the PXIe-9848/9848H can easily manage simultaneous 8-CH data streaming. High density and high speed digitizer features ideally position the PXIe-9848/9848H for applications such as LIDAR, radar signal acquisition, and PSU (Power Supply Unit) testing applications.The PXIe-9848 provides a flexible set of input ranges from ±0.2V to ±2V, software selectable 50Ω or 1MΩ input impedance, a wide variety of triggering options and tight synchronization capability, all maximizing convenience of use. In addition, ADLINK provides the PXIe-9848H, features a x15/x50 signal condition module providing both high input voltage range of ±100V and high dynamic performance, delivering the optimum solution to measurement range expansion in a PXI system.
-
product
SHC68-C68-D4, 68-Pin, Male VHDCI to 68-Pin, Male VHDCI, 50 Ω, Shielded Digital Cable - 1m
196275-01
The SHC68-C68-D4, 1m, Digital Cable connects NI 6535/6/7, 654x, 655x, and 657x digital instruments with other NI accessories like the CB-2162 Connector Block or SMB-2163 Terminal Block. You can also use it with certain Digital I/O Adapter Modules for FlexRIO, Digitizer Adapter Modules for FlexRIO, Signal Generator Adapter Modules for FlexRIO, and high-speed serial instruments. It is flexible and easily fits around custom test fixtures and other equipment. It is a shielded, 50 Ω cable and is offered in different lengths.
-
product
PXIe Semi-Dynamic Digital I/O Module, 64-Channel
42-419-001
The 40-419-001 (PXI) and 42-419-001 (PXIe) are a 64-channel digital I/O modules suitable for operating external devices, such as power, RF and high voltage relays, solenoids and lamps. They can also be used for interfacing with external logic such as a programmable instrument with a BCD interface depending upon the module’s driving capabilities.
-
product
Signal, Contact, Receiver, TriPaddle, 10 Amp, 14-18 AWG
610110177
Primary mating contact 610110113. (May mate with other ITA contacts, as well.)Specifications Operating Voltage & Current 10 Amps Max. Continuous (14 AWG)600 Volt Max. use of wire Mil-W-16878/4Contact Resistance 4 mOhms Max.Measured at 50 mV @ 100 mADielectric WithstandingVoltage (DWV) 1500 VDC Min.Insulation Resistance 4000 MOhms Min.Contact Body BeCuContact Plating 30µ” Au over 100µ” NiContact Termination Crimp/SolderCycle Life 20,000 CyclesRoHS Directive 2011/65/EU Status CompliantREACH Article 33 Status CompliantECHA Article 59 of Reach Regulation CompliantAVG Mating Force (lbs.) 0.41
-
product
sbRIO-9403, Non-Enclosed, 5 V/TTL, 32 Bidirectional Channels, 7 µs C Series Digital Module
780539-01
Non-Enclosed, 5 V/TTL, 32 Bidirectional Channels, 7 µs C Series Digital Module - The sbRIO‑9403 is a configurable digital I/O interface for input or output with shift‑on‑the‑fly capabilities. Each channel features transient isolation between the I/O channels and the backplane. With reconfigurable I/O (RIO) technology (CompactRIO only), you can use the LabVIEW FPGA Module to program the sbRIO‑9403 for implementing custom, high-speed counter/timers; digital communication protocols; pulse generation; and other applications.
-
product
Dynamic Digital I/O (3U), 16 Ch., Per Pin Control, Up To 200 MHz W/256MB Memory & LVDS
GX5293
The GX5290 Series are a high performance, cost-effective 3U PXI dynamic digital I/O boards offering 32 digital input or output channels with dynamic direction control. The GX5290 Series also supports deep pattern memory by offering 256 MB of on-board vector memory with dynamic per pin direction control and with test rates up to 200 MHz. The single board design supports both master and slave functionality without the use of add-on modules.Dynamic Digital I/O (3U), 16 ch., per Pin Control, up to 200 MHz w/256MB Memory & LVDS
-
product
Signal, Contact, ITA, QuadraPaddle, 5 Amp, .025" Square Post for Wire Wrap with Anti-Rotation
610138122
Primary mating contact 610138200. (May mate with other Receiver contacts, as well.)Available in twin-female, crimp/solder, twin male, and wire-wrap design, QuadraPaddle contacts are engineered for flexible interconnect options. Rated at 5 amps continuous (1250 VAC) with a 2 ounce insertion force, QuadraPaddle contacts provide 4 reliable points of contact per pin, outstanding electrical performance, and low mating force.Specifications Operating Voltage & Current 5 Amps Max. Continuous; 600 volt Max. use of wire Mil-W-16878/4Contact Resistance 25 mOhms Max.Measured at 50 mV @ 100 mADielectric WithstandingVoltage (DWV) 1500 VDC Min.Insulation Resistance 5000 MOhms Min.Contact Body BrassContact Plating 30µ” Au over 100µ” NiCycle Life 20,000 CyclesRoHS Directive 2011/65/EU Status CompliantREACH Article 33 Status CompliantECHA Article 59 of Reach Regulation CompliantAVG Mating Force (lbs) 0.24
-
product
PXI Semi-Dynamic Digital I/O Module, 64-Channel
40-419-001
The 40-419-001 is a 64-channel digital I/O module suitable for operating external devices, such as power, RF and high voltage relays, solenoids and lamps. It can also be used for interfacing with external logic such as a programmable instrument with a BCD interface depending upon the module’s driving capabilities.
-
product
Synchro to Digital and Resolver to Digital Converters
Computer Conversions Corporation
Resolution: Up to 20 Bit Single-speed Resolution, Up to 24 Bits Multi-Speed Multi-Turn Resolution.Accuracy: +/- 7 to +/-19 arc seconds 20 bit, +/-40 arc seconds 16 bit, +/- 1',+/-2.3 and +/-4' Reference Inputs: 2- 11.8V 26/ 115Vrms L-L 47 to 10,000 Hz. Isolated to > 500VDCSignal Inputs: 2 - 11.8, 26, 40, 90V.L-L. Isolated to . 500VDC.Options: Multispeed synchro input and bus card interface.
-
product
PXI-6528, 48-Channel, 24 Sink/Source Inputs, 24 Sink/Source Outputs, Channel-Channel Isolated, PXI Digital I/O Module
778543-01
48-Channel, 24 Sink/Source Inputs, 24 Sink/Source Outputs, Channel-Channel Isolated, PXI Digital I/O Module—The PXI‑6528 is an industrial, parallel digital I/O interface. With programmable power-up states, you can configure the initial output states in software to ensure safe operation when connected to industrial actuators. If a computer or application fault occurs, the PXI‑6528 can use digital I/O watchdogs to switch to a configurable safe output state to ensure detection and safe recovery from fault conditions. Programmable input filters eliminate glitches/spikes and provide debouncing for digital switches/relays through a software-selectable digital filter.
-
product
PCIe 16 Bit Multi-purpose Digitizer - up to 20 MS/s on 8 Channels (Single Ended) or 4 Channels (Differential)
M2P.5923-X4
The M2p.59xx series allows recording of up to eight single-ended channels or up to four differential channels both with sampling rates of up to 125 MS/s. These PCI Express cards offer outstanding A/D features both in resolution and speed. The cards can be switched between single-ended inputs with a programmable offset and true differential inputs. If used in differential mode each two inputs are connected together reducing the number of available channels by half. The 16 bit vertical resolution have four times the accuracy compared to 14 bit cards and sixteen times the accuracy if compared with a 12 bit card. All boards of the M2p.59xx series may use the whole installed on-board memory of up to 512 MSamples completely for the currently activated number of channels.
-
product
PCIe 8 Bit High Speed Digitizer - 1.25 GS/s on 4 Channels, 500 MHz Bandwidth
M4I.2212-X8
The 9 models of the M4i.22xx-x8 Express series are designed for the high speed data acquisition. Each of the input channels has its own A/D converter and its own programmable input amplifier. This allows the recording of signals simultaneously on all channels without any phase delay between them. The extremely large on-board memory allows long time recording even with the highest sampling rates.
-
product
PCI-6515, 64-Channel, ±30 VDC, 32 Sink/Source Inputs, 32 Sink Output, Bank-Isolated Digital I/O Device
778835-01
The PCI-6515 is an industrial digital I/O interface, with eight banks of isolated channels. You can wire each input bank in a source or sink configuration. With programmable power-up states, you can configure the initial output states in software, to ensure safe operation when connected to industrial actuators. If a computer or application fault occurs, the PCI-6515 can use digital I/O watchdogs to switch to a configurable safe output state to ensure detection and safe recovery from fault conditions. Programmable input filters eliminate glitches/spikes and provide debouncing for digital switches/relays through a software-selectable digital filter.
-
product
PXI Digital Multimeter, 6 digit, Enhanced Performance
M9183A
The Keysight M9183A is a 6 digit PXI digital multimeter that measures common parameters such as DCV, DCI, ACV, ACI, 2- and 4-wire resistance, frequency, capacitance, and temperature. It offers40 ppm basic DCV measurement accuracy, excellent noise rejection, and handles inputs of up to 300 V.
-
product
PCIe 16 Bit Multi-purpose Digitizer - up to 5 MS/s on 4 Channels (Single Ended) or 2 Channels (Differential)
M2P.5912-X4
The M2p.59xx series allows recording of up to eight single-ended channels or up to four differential channels both with sampling rates of up to 125 MS/s. These PCI Express cards offer outstanding A/D features both in resolution and speed. The cards can be switched between single-ended inputs with a programmable offset and true differential inputs. If used in differential mode each two inputs are connected together reducing the number of available channels by half. The 16 bit vertical resolution have four times the accuracy compared to 14 bit cards and sixteen times the accuracy if compared with a 12 bit card. All boards of the M2p.59xx series may use the whole installed on-board memory of up to 512 MSamples completely for the currently activated number of channels.
-
product
FPGA PXIe High-Performance Digital I/O Card
GX3700e
The GX3700e is a user configurable, FPGA–based, 3U PXI Express card offering 160 digital I/O signals which can be configured for single-ended or differential interfaces. The card employs the Altera Stratix III FPGA, which can support SerDes data rates up to 1.2 Gb/s, digital I/O clock rates of 700 MHz, and features over 45,000 logic elements and 1.836 Kb of memory. The GX3700e is supplied with an integral expansion board providing access to the FPGA’s 160 I/Os. Alternatively, users can design their own custom expansion cards for specific applications - eliminating the need for additional external boards which are cumbersome and physically difficult to integrate into a test system. The design of the FPGA is done by using Altera’s free Quartus II Web Edition tool set. Once the user has compiled the FPGA design, the configuration file can be loaded directly into the FPGA or via an on-board EEPROM.
-
product
PXI-2515, 35-Channel, 0.25 A PXI Signal Insertion Switch Module
778572-15
35-Channel, 0.25 A PXI Signal Insertion Switch Module—The PXI‑2515 is a multiplexer switch module that enables connectivity by routing high-speed digital I/O (DIO) signals between a device under test (DUT) and an NI high-speed DIO device or a parametric measurement device. You can use modules such as PXI Source Measure Units (SMUs) and PXI Digital Multimeters (DMMs) with high-speed digital devices. With the PXI‑2515, you can perform parametric tests on digital pins without external connectivity or impedance mismatch challenges.
-
product
VXG Microwave Signal Generator
M9384B
The M9384B VXG is the industry's first dual-channel microwave signal generators capable of up to 44 GHz signals.
-
product
FieldFox Handheld Microwave Signal Analyzer, 44 GHz
N9961B
A lightweight, durable, software-enabled, microwave signal analyzer, interference analyzer, distance-tracking generator, preamplifier, power meter, and more.
-
product
PXI Breadboard Module, 1-Slot, 50-Pin D-Type
40-220A-501
The 40-220A series of breadboard modules allow the user to construct their own circuit in situations where a suitable PXI module is not available. For example when it is required to integrate a non-switching function into a PXI chassis. Typical applications include: Creating custom circuitry that can be housed in on a 3U board, or to build special one-off switching modules.
-
product
12GHz Four Channel Signal Generator 19" 1U Rack Module
LS1294R
The LS1294R, 12GHz four channel RF Analog Signal Generator, offers industry leading performance, in a 1U, 19” space efficient, rack-mounted box. The LS1294R features four phase coherent channels, exceptionally fast switching speed, superior signal integrity and purity and all the necessary modulated signals for analog communication systems. The LS1294R was designed to offer excellent performance and abilities combined with an affordable price tag, needed from the R&D benches to the production lines.
-
product
NI-9425 , 24 V, 32-Channel (Sinking Input), 7 µs C Series Digital Module
780176-01
24 V, 32-Channel (Sinking Input), 7 µs C Series Digital Module - The NI‑9425 works with industrial logic levels and signals to connect directly to a wide array of industrial switches, transducers, and devices. Each digital input line is compatible with 24 V logic levels. The NI‑9425 offers isolation between the input and output banks from channel to earth ground. You cannot use the NI‑9425 in a CompactDAQ chassis to perform counter operations.
-
product
Ethernet/LXI digitizerNETBOX 16 Bit Multi-Purpose Digitizer - 125 MS/s on 12 Channels, 80 MS/s on 24 Channels, 24 Single-Ended Inputs, 12 True Differential Inputs
DN6.596-24
The digitizerNETBOX DN6.59x series allows recording of up to 48 synchronous channels with sampling rates of 20 MS/s up to 125 MS/s. These products offer outstanding A/D features both in resolution and speed as a remote instrument. The powerful A/D amplifier section offers 6 different input ranges, programmable offset and a software switching from single-ended (full number of input channels) to true differential (half number of input channels).
-
product
PXI Breadboard Module, 2-Slot, 78-Pin D-Type
40-220A-402
The 40-220A series of breadboard modules allow the user to construct their own circuit in situations where a suitable PXI module is not available. For example when it is required to integrate a non-switching function into a PXI chassis. Typical applications include: Creating custom circuitry that can be housed in on a 3U board, or to build special one-off switching modules.
-
product
PXI Opto-Iso Digital I/O 32bit out 16bit in
40-490-002
The 40-490 Digital I/O Modules are designed for applications requiring optically isolated digital I/O, typically in industrial automation. This modules features 32 digital outputs and 16 digital inputs which may be programmed by word or individual bit. Power for the isolated section of the module is built onto the board in model 40-490-001, or this can be supplied externally in model 40-490-002.
-
product
PXIe-5764, 16-Bit, 1 GS/s, 4-Channel PXI FlexRIO Digitizer
785171-01
The PXIe-5764 is a PXI FlexRIO Digitizer that simultaneously samples four channels at 1 GS/s with 16 bits of resolution and features 400 MHz of analog input bandwidth. With up to 70 dB of SNR, the PXIe-5764 is ideal for applications that require a wide dynamic range with a wideband digitizer. The FlexRIO driver includes support for finite and continuous streaming modes, and you can implement custom algorithms and real-time signal processing on the LabVIEW-programmable Xilinx Kintex UltraScale FPGA. Available in AC and DC coupled variants, the PXIe-5764 is ideal for both time and frequency domain applications, including radar prototyping, LIDAR, communications, microscopy, OCT, event detection, and particle physics.
-
product
Signal, Patchcord, ITA, 36", QuadraPaddle, 22 AWG White, Single Ended ( 5 Amps)
7-121922000-036
Signal, Patchcord, ITA, 36", QuadraPaddle, 22 AWG White, Single Ended ( 5 Amps).
