Optical Amplifiers
Devices that boost light signal in an optical fiber network. The optical signal is amplified directly without need for electrical conversion.
-
product
Lock-in Amplifier
HF2LI
The Zurich Instruments HF2LI (high-frequency, 2 inputs) is a digital lock-in amplifier covering the frequency range between DC and 50 MHz. It features 2 physical input channels so that it can replace 2 devices in many measurement setups. The 128-bit digital signal processing delivers superior precision thus boosting both the noise performance and the dynamic reserve. With these unprecedented capabilities, the HF2LI brings lock-in amplification to a new level and enables new applications in a frequency range that was previously tied to analog instrumentation. The computer is connected by a high-speed USB interface, which allows data acquisition at high rates. The HF2LI is delivered with a fully featured graphical user interface and a choice of programming interfaces that greatly add to the usability of the instrument.
-
product
System Amplifier
Solid state Broadband Amplifiers are designed for optimum operation for IED Jammer Applications which is featured as below. We can rack mount any of our existing amplifiers or systems or custom design the amplifier and enclosure. Each Rack Mounted Amplifiers are built around a large bonded fit heat-sink rated for high temperature ambient operation.
-
product
HF Amplifier
Prometheus
The design of the Prometheus is the result of over 10,000 hours of research and development, encompassing hundreds of hours of mathematical analysis, computer simulation and modeling, and numerous prototypes and experiments spanning over a five year period. The result is a rugged, commercial quality amplifier designed to run cool under 1500W continuous SSB, CW or RTTY, with special ferrite transformers and combiners designed for full power operation even on 160 meters. Although our custom transformers are more expensive and difficult to manufacture than competing designs, they do not saturate or heat up beyond the Curie point, thereby becoming irreversibly damaged and destroying the RF transistors in the process.
-
product
Optical Fiber 1×13 Switch
OFSW - 1 × 13
Hangzhou Huatai Optic Tech. Co., Ltd.
OFSW- 1×13 is a 1×13 prism optical switch. It can support 1 optical fibers input and 13 fiber output, channel switch. Wide operating wavelength range, low insertion loss and speedy switching rate, can use network trends configuration, network monitor and lab application.
-
product
PXI/PXIe MEMS Optical Switch, Dual Insert/Bypass
40-860A-522-M
The 40/42-860A-522-M is a PXI/PXIe dual insert/bypass switch with ST connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. They are also available with an optional hardware interlock which, when activated, will return all optical switches to their default unpowered state.
-
product
Optical Modules And Components
Luna offers a complete line of high performance active and passive fiber optic modules and components for a wide range of fiber optic systems, including interferometric systems for fiber optics sensing, fiber optic gyroscope (FOG) and optical coherence tomography (OCT).
-
-
product
MTP MPO Fiber Optics
Shanghai Tarluz Telecom Tech Co., LTD
A high performance MPO connector with multiple engineered product enhancements to improve optical and mechanical performance when compared to generic MPO connectors.
-
product
C-band Optical Spectrum Analyzer Mocule Specification
CA92001
UC INSTRUMENTS CA9001 Portable Optical Spectrum Analyzer
-
product
RF Amplifier
SA1001H
Hangzhou Softel Optic Co., Ltd.
*SA1001H Indoor Bi-directional Amplifier are special amplifiers designed for the last”1km” of the bi-directional transmission network.. Special CATV RF modules packaged in SOT-115 are used as forward channel; Microwave tube push-pull circuit with low noise are used as backward channel ;It has the characteristics of low power consumption，high reliability and excellent cost performance. And it is suitable for small and medium sized CATV bi-directional transmission network*It is more convenient for debug engineering debug, because of the plug-in diplexer filters with built-in adjustable equalizers, adjustable attenuators, plug-in output splitters and scientific and reasonable ports for online test.*These equipments will work in the field rugged environment for a long time continuously, because of the aluminium alloy casing, good heat dispersing performances, beautiful looks, dependable linear power supply and lightning protection systems.
-
product
RS485 Mode SI-module With Optical Isolation
MX485-G
RS485 mode SI-module with optical isolation
-
product
Optical Fiber Sensors
Optical sensors based on Fiber Bragg technology (FBG) are a reliable and safe solution for numerous testing applications, such as in structural testing and lightweight construction. Benefit from perfectly-matched measurement chains when using an optical FBG sensor based on Fiber Bragg Gratings made by HBM FiberSensing.
-
product
PXI/PXIe MEMS Optical MUX, 4-Channel, Multi-Mode
40-850A-014-M50-HI
The 40/42-850A-014-M50-HI is a PXI/PXIe 4-channel multiplexer with FC/APC connectors, includes hardware interlock and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications.
-
product
Fiber Optic Test Equipment
OZ Optics has also introduced a line of test and measurement equipment initially developed for our internal use. We manufacture many of the components used in our test and measurement equipment making them cost and performance competitive.
-
product
Optical Coordinate Measuring System
MaxSHOT 3D
Creaform’s MaxSHOT 3D lineup is a game changer for product development, manufacturing, quality control and inspection teams that need the highest measurement accuracy and repeatability as much for large‑scale projects than parts from 2 to 10 m. Imagine achieving accuracy better than 0.015mm/m! Thanks to its sophisticated user guidance technology and easy‑to‑use software, the MaxSHOT 3D is ideal for users of all levels—even non‑metrology experts—so that you gain peace of mind knowing your measurements are always right on the dot and you increase process efficiency. If you consistently work on large‑scale projects, the MaxSHOT 3D is your go-to solution to slash budget-busting measurement mistakes, improve product quality, increase process efficiency—and minimize overall operating costs.
-
product
Amplifier Systems Broadband
Systems are complete. They plug into an outlet and are ready to go. Our standard systems are 3U, which is 5.25″ and 5U, 8.75″. Systems are available with or without IEEE-488, RS-232 and Ethernet connectivity. Amplifiers Systems are available in both Broadband and Band-Specific frequencies. We are well-known in the industry for successfully adapting our amplifiers or custom designing new solutions to suit each unique project. Please refer to our Adapted & Custom Design Solutions link to begin formulating your performance objectives and other criteria.
-
product
Optical Fiber Cable Testing Equipment
Optical fiber consists of a core and a cladding layer, selected for total internal reflection due to the difference in the refractive index between the two. In practical fibers, the cladding is usually coated with a layer of acrylate polymer or polyimide. This coating protects the fiber from damage but does not contribute to its optical waveguide properties. Individual coated fibers then have a tough resin buffer layer and/or core tube(s) extruded around them to form the cable core. Several layers of protective sheathing, depending on the application, are added to form the cable. Rigid fiber assemblies sometimes put light-absorbing ("dark") glass between the fibers, to prevent light that leaks out of one fiber from entering another. This reduces cross-talk between the fibers, or reduces flare in fiber bundle imaging applications Optical fibers are very strong, but the strength is drastically reduced by unavoidable microscopic surface flaws inherent in the manufacturing process. The initial fiber strength, as well as its change with time, must be considered relative to the stress imposed on the fiber during handling, cabling, and installation for a given set of environmental conditions. There are three basic scenarios that can lead to strength degradation and failure by inducing flaw growth: dynamic fatigue, static fatigues, and zero-stress aging.
-
product
Optical Camera Trigger
The Optical Camera Trigger is an optical sensor that detects pulsed light sources and generates outputs to trigger a camera. The front aperture of the Optical Trigger must be directed at a light source that provides the necessary properties for trigger activation. (e.g. a laser flash lamp, a pick-off source from the main laser beam, or similar). The light source may be a direct or indirect pulsed waveform.
-
product
Wideband Power Amplifiers
Krohn-Hite Wideband Power Amplifiers are designed to meet today's industrial needs where wideband, precision performance is required. Applications include: meter calibration, piezo transducer driving, bridging applications requiring high input and low output impedance, low distortion ac power source, ion beam deflection, vacuum tube driver, ink jet testing and design and many more.
-
product
High Speed Op Amplifiers (Bandwidth ≥ 50MHz)
Analog Devices high speed (> 50 MHz) amplifiers are the number one selling brand of high speed amplifiers in the world today. Whether it's wide bandwidth, high slew rate, or low distortion, no one sets more performance standards for next generation designs, with the widest portfolio of leading edge products, than Analog Devices. Designers who want dependable, reliable parts that enable the highest performance from their design come here for the ultimate source in high speed op amps.
-
product
2-MGEM Optical Anisotropy Factor Measurement System
The 2-MGEM Optical Anisotropy Factor Measurement System is a normal-incidence polarization reflection microscope designed to measure the sample Mueller matrix and is a 2008 R&D 100 Award Winner. This system is designed specifically to evaluate the Optical Anisotropy Factor (OPTAF) of cross sections of TRISO nuclear fuel pyrocarbon layers. Other possible material characterizations include measuring Mueller matrix elements of other crystals, carbon compounds, and thin film coatings (e.g. surfacedeposition films) at normal incidence. The 2-MGEM can also measure retardation (d), circular diattenuation (CD) and the polarization factor (ß). These parameters are not measurable using older techniques, since those techniques do not incorporate a compensating optical element.
-
product
Optical Fiber Cleaver
SH-40
Shenzhen Sharingtek Communication Co., LTD
SH-40 fiber optic cleaver is the new type of fiber cutter with high precision, greatly improving the working efficiency and efficiency.
-
product
High Voltage Amplifier
WMA-100A
The WMA-100A model is our cost-effective, compact, general purpose high voltage amplifier. With its high quality and small form factor, it is the ideal choice for any experiment that requires an all-round, reliable high voltage amplifier. It can also be used as a stand-alone low noise high voltage power supply. Two WMA-100A amplifiers and a WMA-IB-HS phase inverter - buffer can be used to double the output voltage.
-
product
Optical Fibers Communications
1. Textbook includes the theoretical and practical details.2. Textbook includes the expected results for reference.3. Problem discussion attached together with answers for instructor.4. Only need oscilloscope and spectrum analyzer to obtain the measured results.
-
product
Optical Probe
1038
TESCO’s Optical Probe provides easy, two-way communication between a PC and a meter.
-
product
Optical Spectrum Analyzer
ID OSA
This instrument is a versatile Optical Spectrum Analyzer (OSA) based on a coherent detection principle provides picometer class spectral resolution across the C-Band (1528.5 – 1567.5nm).
-
product
Fiber Optic Power Meter
The handheld Fiber Optic Power Meter is a user-friendly tool for engineers testing and maintaining fiber optic systems & networks. Both compact and rugged, these devices can be used for absolute optical power measurements, as well as relative loss measurements. In addition, high accuracy and a user self-calibration function result in an excellent overall value.
-
product
RF Amplifiers up to 500 MHz
Narrow and Broad band RF modules and rack mount amplifier systems using solid state devices including LDMOS and GaAsFET in Class A and Class A/B topologies for AM, FM, VHF, and UHF bands with output power ranging from 0dbm to 60dbm.
-
product
Optical Measuring Machines
QFP offers a complete line of optical measuring machines that allow us to offer the most suitable solution to satisfy any measurement need.
-
product
Semiconductor Manufacturing Optics
No lithography without optics. No semiconductors without lithography. Without semiconductors there would be no microchips, without microchips no computers – no high-tech products. As an OEM (Original Equipment Manufacturer) supplier, ZEISS enables the semiconductor industry worldwide with optics and other optical modules.
