Filter Results By:
Products
Applications
Manufacturers
Network Probes
Monitor and analyze networks.
-
product
Active Probe, 5 Hz to 500 MHz
41800A
The Keysight 41800A Active Probe provides high input impedance from 5 Hz to 500 MHz. The Keysight 41800A is a valuable tool when used with a network and spectrum analyzer for circuit signal analysis.
-
product
Video Inspection Probe
With today's high data rates and high definition services, connector quality and inspection has never been so important. Research reveals that up to 75% of all optical network failures are attributed to poor connector quality - reduce your installation time and ensure your network is reaching its full potential.The Video Inspection Probe (VIP) application for Anritsu field testing platforms gives operators a safe, easy way to analyze and document connector conditions.
-
product
Cable Tester
The MapMaster™ mini detects faults and locations of RJ45 network cables. Good terminations, causes of faults and locations of cables are displayed on an LCD display. A set of five mapping remotes is included for locating cables terminated in wall jacks or patch panels. A built-in tone generator with 4 different tone combinations can be used with a tone probe to detect where a cable is routed and the location of the end of the cable.
-
product
OTDR
EXFO-100
Hangzhou Softel Optic Co., Ltd.
* Top user-friendliness: one-button testing, combined with EXFO’s proprietary FTTx software package (macrobend/fault finder, pass/fail indicators)*Multiple options, including power meter, visual fault locator (VFL), fiber inspection probe, printer and IP testing*Fault Finder mode, for quick identification/location of a fiber break*Complete connectivity flexibility: USB stick compatibility and USB cable data download via ActiveSync**Advanced TFT transflective color display, for assured legibility under direct sunlight or in other demanding outside conditions*Handheld, small, lightweight unit: 1 kg (2.2 lb)*Built-in ruggedness for outside-plant usage*Troubleshooting option, enabling in-service, out-of-band network testing *EXFO’s AXS-100 Access OTDR combines the industry’s leading OTDR technology with power meter functiona lities in one powerful handheld unit.Optimized for testing passive optical networks (PON) within FTTx architectures, it offers several wavelength configurations and a wide range of options, for first-class flexibility. Use it at the optical network terminal(ONT), drop terminal or fiber distribution hub (FDH) for FTTH distribution(F2) fiber characterization, troubleshooting and fault locating.
-
product
Multilogger
M1220
Universal datalogger with 4 hardware inputs. Two inputs for temperature-humidity probes and two inputs for thermocouples K, J, S, B, T, N. Multilogger can be installed permanently to Ethernet network or work as portable device. Included is traceable calibration certificate in accordance with EN ISO/IEC17025.
-
product
TDR Probe
TDP Blade Probe
The TDP Blade Probe enables fast and convenient TDR measurements and debugging. The BladeProbe tips are made from strong and rigid beryllium copper blades for handheld and probe station probing. The passive probe can be used to measure impedance, clock jitters, and skews. The TDP BladeProbe series can be connected to TDR, high performance scopes, and vector network analyzers.
-
product
Voltage Probe
KHZ43201
Beijing KeHuan Century EMC Technology Co,.LTD
The KHZ43201 voltage probe is a standard low resistance test probe, which meets the technical requirements for this product in the CISPR16-1 and CISPR14-1 test equipment. When measuring the interference voltage of the power grid, the artificial power supply network cannot be used at the load port, and sometimes it is necessary to use a voltage probe to measure the interference of the signal port, the load port, and the antenna port. The input impedance of the voltage probe to the ground wire is greater than 1.5KΩ, which can protect the input terminal of the receiver.
-
product
Injection Transformer
J2101A
The injection transformer is presently the prevalent method for connecting the network analyzer to the circuit being tested, and is primarily used for control loop stability measurements. The goal of the transformer is to inject a signal into the control loop being measured, without impacting the performance of the loop. In order to accomplish this to a reasonable degree, The transformer is isolated and therefore is capable of floating on a high voltage, such as a Power Factor Corrector (PFC), which is often close to 400VDC. Measuring voltages that exceed the voltage rating of the FRA inputs require attenuation probes.
-
product
Compact Monitoring Probe
ISDB-T/Tb
Network operators:automate the tests of new transmittertemporary monitoring/investigation toolrebroadcasting receiver: RF to ASI or IPBroadcasters: off-air monitoring probe to validate the on-air contentTV/STB producers: automated tests against a professional receiverLabs: easy & simple access to live DTV sources via RF
-
product
Rack Based Test Solutions
Most equipment manufacturers and large enterprises prefer rack-based test tools as they are compact and higher density form factor solution for testing, monitoring, and troubleshooting network conditions. GL’s Multiple TDM Optical and Packet (mTOP™) rack enclosure can house any combination of USB based test equipment which are easily deployed and securely fixed to an equipment rack to provide extraordinary scalability to test switches, routers and end-to-end networks. These rack based platforms incorporates the basic test unit along with the necessary PC hardware, Windows® 10 64-bit operating system and remote accessibility via scripting and remote desktop. There are no moving parts with the unit, so reliability and longevity are integral. GL’s latest mTOP™ Probe stand-alone hardware variant is an all-in-one self-contained test instrument. The mTOP™ Probe can include any of the multiple TDM Optical and Packet interfaces USB device combined with the PC into one single box. The comprehensive mTOP™ Probe hardware unit is designed for easier portability and convenient for field testing which incorporates the testing features for multiple interfaces along with necessary PC hardware in a single box. GL’s USB based test equipment - PacketExpert™ (Ethernet), tProbe™ (T1/E1), USB T3/E3 (TDM), Dual UTAs (Analog/Wireless), and LightSpeed1000™ (SONET SDH) to support multiple interfaces in a compact rack space or included in a portable Probe unit.
-
product
Service Assurance Remote Probe for IPTV, OTT, VoiP & Internet
µNET
The μNET is a palm size probe for testing and monitoring Triple-Play services (IPTV, VoIP, Internet) at the customer set top box or the last mile concentrator (ie.GPON mux). Multiple μNET probes can be used throughout the IPTV network on a temporary or permanent basis. Test results are sent to the external FTP server. All tests are performed in a cycle set up by the user.
-
product
Vector Network Analyzer Extenders
VNAX
VDI''s VNA Extenders deliver high performance network analyzer frequency extension into the THz range. Models cover 50 GHz to 1,100GHz with additional bands in development. VDI modules come in a variety of form factors and configurations including our original Standard-size Modules and new Mini Modules that reduce volume up to 75%. In addition to our full Transceiver (TxRx) modules, VDI also offers Transmit-Reference (TxRef) modules and Receive only (Rx) modules that deliver optimized performance for specific applications. These modules combine high test port power and exceptional dynamic range to deliver industry leading performance. They are compatible with most network analyzers and can be integrated into probe stations and antenna chambers.
-
product
OverHead Lines Contact Voltage & Low Voltage Indicator
LVD-415
Standard Electric Works Co., Ltd
● No batteries required.● Every circuit is doubled.● Buzzer indicates voltage detected.● Led indicates voltage detected.● Neon scale indicates voltage.● Dual HBC fuses.● High grade fiber glass probes.● Super polished fiber glass.● High strength connecting cord.● Heavy duty rated.● Replaceable tips.● Choice of tips available.● Lightweight.● Small storage space.● Strong strength reliefs.● Double poles non-polarized.● Suitable for 45 to 70 Hz networks.● Contact detector type.● Passive circuitry.● Fiber glass 1.6mm - CU 35um PCB.● Super bright neon lights and LEDs.● Ergonomically-designed.● EN 61010-031 CAT IV 500V.
-
product
Digital RF Power Monitor
3024
The COMM-connect 3024 RF Power Monitor from LBA Technology can control up to 8 external RF Measuring heads. The high dynamic range with external couplers and RF measuring heads cover from 1W to 1MW. The Power conversion algorithms handles multi carrier, multi mode, peak, average and RMS signals. The power readout is auto scaled and VSWR can be calculated between any probes. Also the measured and calculated results along with alarms can be shown in the local LCD. The instrument has SNMP support to allow network management. The instrument can be configured for VSWR and Power limits to give alarms. The alarms can be configured to operate relay drivers or isolated Optcouplers. The alarms can also be configured as SNMP traps sending relevant information to the network control center. The COMM-connect 3024 WEB enabled RF Power Monitor gives an unlimited number of applications to monitor and control the last part of your RF network installation from transmitters to the antenna.
-
product
Network Probe for TC-NT2
TC-TP1
TRENDnet´s TC-TP1 is an easy-to-use amplified inductor and tone probe that is used for tone tracing and line testing. The TC-TP1 features a simple push button that provides easy operation and conserves battery power. This ergonomically designed device comes with adjustable volume control and signal LED for enhanced accuracy in noisy environments.
-
product
Environmental (Radiation) Monitoring System
Hawk® EMS
The Hawk® EMS is a wall or tripod-mounted radiation monitoring and alarm system designed for use with the Hawk® Radius dual sensor radiation probe. Each EMS System comes with a Hawk Radius Probe. The system is extremely energy efficient and can run for weeks on an internal 9 volt back-up battery if power fails. It is well suited for operating on a small solar panel, which is an optional accessory. The Hawk® EMS features two displays that show the radiation levels measured by each of the probe’s two detectors: the weatherized “pancake-style” Geiger-Mueller tube — which measures alpha (if configured for it), beta, low energy gamma, and x-radiation — and the energy-compensated gamma tube which measures penetrating gamma dose rate. The probe can be mounted next to the EMS system or outdoors, or in adjacent rooms on cables up to 100 ft in length. Standard cable is 3 meters in length. Optional signal booster can support cable lengths longer than 100 feet. Optionally the system can also be configured to share data on ethernet or wireless networks.
-
product
Remote Test Unit (RTU) Expert
RTU Series
VeEX’s Remote Test Units (RTU) are self-contained, scalable test and monitoring probes for communications networks. When used as part of the VeSion cloud-based monitoring system, these rackmount probes are optimized to work with a centralized server system. In addition, the probes can be operated in standalone mode via web browser.
-
product
PTP Toolbox
OSA 5410/11
The OSA 5410 Series is a family of compact and cost-effective synchronization distribution and assurance devices that bring the power of Syncjack™ to any network. Following a toolbox approach, the family members of the OSA 5410 Series can be utilized in a variety of network synchronization applications including IEEE 1588v2 Access Grandmaster, Boundary and Slave Clock, GNSS receiver and Primary Reference Time Clock (PRTC), synchronization signal conversion and sync probe applications.
-
product
Multilogger
M1140
Universal datalogger with 4 hardware MiniDIN inputs for connecting temperature and humidity probes. Multilogger can be installed permanently to Ethernet network or work as portable device. Included is traceable calibration certificate in accordance with EN ISO/IEC17025.
-
product
Network, Port ID And Cable Tester
One for All PH-400
The One For All is an all-in-one network tester, tone generator, cable tester, and port ID finder. It comes with a remote unit, allowing pin-by-pin tests of installed cables in addition to patch cables. The office ID feature allows the user to check the ID number of up to 100 networks or patch panel outlets without labeling the cables manually, and the tone generator traces cable using a tone detectable by any market tone probe. The network tester blinks the network hub or NIC port light for the cable being tested, allowing easy cable and outlet identification; and it identifies network speed (10 Mbps vs. 10/100 Mbps vs. 10/100/1000 Mbps) and activity. Line tester included for detect live circuits and preventing damage to the tester.
-
product
K-50 Series Probes
The K-50 coaxial probe provides an instrumentation-quality interface for broadband R.F. measurements up to 4 GHz. With the K-50 R. F. circuit design, impedance characterization measurements can be performed using it as a Network Analyzer port-extending accessory. Accurate and repeatable small signal and R.F. power (50 Watts) measurements provide consistent and repeatable results.
-
product
Transmission Line Probes
Transmission line probes are a special type of passive probe designed for use at very high frequencies. They replace the high impedance probe cable found in a traditional passive probe with a precision transmission line, with a characteristic impedance that matches the oscilloscope input (50 Ohm). This greatly reduces the input capacitance to a fraction of a picofarad, minimizing the loading of high frequency signals. A matching network at the tip increases the DC input resistance. While they have lower DC input resistance than a traditional passive probe (usually 500 Ohm) to 1kOhm), the input impedance of these probes remains nearly constant over their entire frequency range. A traditional /10 passive probe will have a 10 MOhm) input impedance at DC, however this impedance drops rapidly with frequency, passing below the input impedance of a transmission line probe at less than 100 MHz.
-
product
Network Toner & Probe Kit
MT-7028
The MT-7028 lets you easily locate and verify the cable status and troubleshoot wiring for continuity, shorts, opens and crossover on RJ45 Lan cable Cat 55e67 (UTP/STP)RJ11/12 Telephone cable Cat. 3 (2/4/6 pin) & normal solid/Stranded wire by alligator clips patch cord. Ideal for all installation and maintenance fields of telecommunication, networking, datacom, Audio/Video, cable TV, and all weather cabling, etc.
-
product
LANTRACKER
PH-100/120
The Lantracker is a network tester, pin-by-pin cable tester, and tone generator all in one. As a network tester, it detects whether a network is active or inactive and displays network speed (10/100/1000 Mbps) in either case. It also flashes the network hub or NIC’s port light corresponding to the cable it is connected to, to show the cable’s port number. As a cable tester, it performs loop-back or remote tests of network, data, voice, and coaxial cables, displaying the results on a pin-by-pin LED display which moves from pin to pin automatically or manually. The Lantracker can be used to test cable or shield integrity, testing network function and speed, and tracing cable using its tone generator function (tone probe not included). Includes an adaptor for testing coaxial-F cable. Uses 1 9V battery.
-
product
Active Differential Probe, 100 kHz to 7 GHz
U1818A
The Keysight U1818A 100 kHz to 7 GHz active differential probe makes it easy to perform high frequency in-circuit measurements using network, spectrum and signal source analyzers. With flat frequency response, low noise floor, and direct power from instrument connection, the U1818A allows measurements to be made while taking full advantage of Keysight's RF analyzers dynamic range.
-
product
4-Channel Broadcast Monitor
The COMM-connect Entry Level Broadcast Power Monitor type 3025 can control two external RF Measuring heads. The high dynamic range with external couplers and RF measuring heads cover from 1W to 1MW. Equipped with the RMS Probes the Power conversion algorithms handles multi carrier, multi mode signals. With the 3026 Diode base probe the power readout gives good repeatable results. The power readout is auto scaled and VSWR will be calculated between the two probes. The COMM-connect Entry Level Power Monitor gives a number of application to monitor and control the last part of your RF network installation from transmitters to the antenna.
-
product
Advanced High Speed Test Probe
SQprobe
SQprobe® is an advanced high speed probe designed for emerging software defined (SDN) and virtualized networks. It monitors IP based voice, video, audio and data streams at Gigabit rates, performing deep packet inspection (DPI) and providing accurate and detailed real time service quality metrics, usage and demographic data.
-
product
Digital Inspector
DI-2000
Many modern network issues can be traced to contaminated or damaged fiber optic connector endfaces. Lightel’s DI inspection probe series provides ergonomic, easy-to-use, and versatile inspection of the endfaces for fiber optic male and female, single and multi-channel connectors.
-
product
Test Probe
UE
Qosmotec Software Solutions GmbH
Qosmotec UE Test Probe offers more flexibility to testers of mobile networks. It is a compact plug & play multi-UE test probe that allows for tests in UMTS, HSPA+ and LTE standards from any location. It can hold a custom set of up to 8 UEs.
-
product
Temperature And Humidity Data Loggers
EL WiFi
The EL-WiFi-TC sensor measures the temperature of the environment in which the probe is situated. The accuracy of the K type probe supplied is ±1.5°C. Data is streamed wirelessly over any WiFi network and can be viewed on a PC using our free software package. Cloud subscription also available
