Resistive Load Banks
Check power source's ability to deliver a given current and voltage at unity power factors.
See Also: Load Banks, AC Load Banks, DC Load Banks, Inductive Load Banks, Reactive Load Banks
-
product
Modular DC Electronic Load LED Simulator
6310/A
Chroma Systems Solutions, Inc.
Chroma 6310A Programmable Electronic Load integrates microprocessor capabilities into each load module and mainframe to provide simple and accurate parallel operation to optimize the speed and control among multiple load modules. All load modules may be configured to work synchronously, to test multiple outputs simultaneously, thus simulating real life applications.
-
-
product
High-power DC Electronic Load (6kW~60kW)
FT68200A/AL/E Series
Shenzhen FaithTech Technology Co., Ltd.
FT68200 series high performance high-power DC electronic load provides three voltage ranges 150 V/600 V/1200 V, maximum current 2400 A per single unit, stand-alone power from 4 kW to 60 kW, expandable up to 600 kW, 10000A by master-slave paralleling. Ultra-high power density, 6kW is with only 4U height. Wider operating region, faster dynamic frequency, as well as transient mode, OCP/OPP test, sequence test, automatic test and battery discharge test functions greatly enhances its test strength and expands application coverage. Furthermore, two times instantaneous overpower loading capability can effectively reduces user’s test cost. Built-in standard RS232, RS485, LAN, USB (serial), optional GPIB and CAN interface, supports SCPI, ModBus RTU and CANopen protocol, which facilitates system integrators. FT68200 series has full protection functions, which can be applied to power battery discharge, DC charging station, charging piles, charging pile modules, vehicle On Board chargers (OBC), high-power switching power supplies, power electronics and other power electronics products.
-
product
LUTHER & MAELZER BARE AND LOADED BOARD TEST PROBES
SERIES LMP 60
MechanicalMINIMUM CENTERS: .100 (2.54)FULL TRAVEL: .160 (4.06)WORKING TRAVEL: .107 (2.72)OPERATING LIFE: 1,000,000 cyclesElectricalMAXIMUM CURRENT: 5 amps continuousat working travel, non-inductiveRESISTANCE: At 35 mA test current,35 mOHMS meanMaterials and FinishesPLUNGER: Heat treated berylliumcopper, 24 Kt gold plated over nickelBARREL: Nickel silver, 24 Kt goldplated over nickel
-
product
Insulation Resistance Measurement
MD 15KVR
The digital insulation tester model MD-15KVR is Megabras' cutting edge insulation analyzer equipment and it is one of the most complete and sophisticated available in the international market. A powerful software allows for further analysis of tests results, including features such as graphical representation and automatic report generation. Its proven technology provides safe, reliable and accurate measurements of insulation resistances up to 15 TΩ, with 4 pre-selected test voltages, 500 V - 5 kV - 10 kV - 15 kV. Other test voltages may be selected in steps of 25 V, 100 V or 500 V.
-
product
Transformer Load Box
FY-H / 645
Wuhan Huatian Electric Power Automation Co., Ltd.
When testing current and voltage transformer, it provides various useful loads, which is an ideal matching product for various transformer verification devices.
-
product
Standard Shackle Load Cell
SS-3.0
The DLM Standard Shackle Load Cell is a high strength marine grade cable connected Load Cell. Manufactured from industry leading Crosby or GN Shackles along with a stainless steel load pin.
-
product
Resistivity Test System
RMS-1000
Accurate and powerful performance. - Possible to get much accurate resistivity value by taking 8 raw data. - Good to check ohmic contact by flowing forward and reverse current.2. We provide various sample mounting board and probe head and tips.3. We have an optional item which can measure in variable temperature. - Room Temperature ~ 300dC.
-
product
PXI MUX 4 Bank, 16 Channel Screened 1 Pole
40-610-021-S-4/16/1
This series of high density multiplexer modules feature a wide range of switching configurations, especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems. Connections are made via a front panel 200-pin connector. Inter-bank linking relays allow multiplexer size to be increased in multiples of in multiples of three by joining the common terminals of adjacent banks. Closing one linking switch produces a 6-channel multiplexer, closing all linking switches produces an 54-channel multiplexer
-
product
Structural Load Monitoring
SLM
Since 2001 ITM has installed structural strain based monitoring systems in the pulp & paper and energy generation industries. For these systems, our engineers and field service technicians turn structures into measurement instruments (load cells). Load outputs from the structural load cells are monitored and published by a realtime controller to its local interface or network historians and HMIs.
-
product
New Resistivity Inversion Software
EarthImager 3D
AGI is proud to introduce the new EarthImager 3D resistivity and IP inversion software. This software inverts resistivity and IP data acquired with electrodes arranged in boreholes and/or on the surface and presents a 3D volume of inverted resistivity data with advanced volume rendering technique. The final resistivity or IP image-volume can be rotated in any orientation, zoomed in and out, and translated to anywhere inside the image window in order to see the volume of interest in detail. Colors representing areas of less interest can be made transparent so that the shape of a pollution plume, for example, can be visible. With EarthImager, 3D resistivity inversion can be as easy as two steps: Read Data and Start Inversion with only a few mouse clicks.
-
product
Channel Load Generator
802.11p
Qosmotec Software Solutions GmbH
When many cars are equipped with 802.11p communication technology, high traffic density will also cause significant load on the radio channel. From normal wireless communication systems it is a known problem, that many users can cause a complete breakdown of the network. Car-to-X communication technology tries to protect itself against those kind of breakdown by a carrier sensing mechanism: Each communication device has to check first, if the radio channel is busy. In that case, it waits for a random delay to avoid packet collision on the radio channel, which causes a loss of both collided packets.
-
product
Load Cell Power Supply
MODEL PSMR
The PSM-R is a self contained AC power bridge excitation supply. This device consists of a low interwinding capacitance AC transformer and a high stability adjustable linear regulator designed specifically for driving transducer bridges. DC excitation is adjustable from 4 to 15 volts output and is capable of supplying 0 to 150 mA in output current. It features remote sensing to eliminate line drop errors and very low noise. It can also be used as a high quality voltage source or reference in many applications. AC input requirements are 105 to 125 VAC at 60 Hz.
-
product
Variable Resistor Load Bank
REOLOAD 100
A variable resistor load-bank with fixed stages connected in parallel and switched in, as required, with an adjustable stage for fine trimming. Designed for testing equipment under load. 1000V (AC or DC). 250A and 2500
-
product
4-Wire Resistance Measurement | Continuity & HiPot Cable & Wire Harness Testers
An add-on option for the CableEye HVX high voltage cable tester series that permits expanded testing for contact and wire resistance as low as 1 mΩ. After checking for opens, shorts, miswires, and resistance limits, the 4-wire Kelvin measurement applies a user-selectable test current from 10 mA to 1 A to determine connection resistance within 1 mΩ. The resistance profile of a model cable may be stored and used as a basis of comparison during later testing to reveal cold solder joints, faulty crimps, recessed pins, pin contact contamination, improper wire gauge, and stress-extruded wire.This option may be purchased with any new HVX tester, or added as an upgrade to any of your existing HVX testers.
-
product
AC / DC Electronic Loads – Benchtop Testing to Automated Test Systems
Chroma Systems Solutions, Inc.
Chroma is the global leader in Electronic Load manufacturing. Chroma’s AC Electronic Loads are designed for testing uninterruptible power supplies(UPS), Off-Grid Inverters, AC sources, and other power devices such as switches, circuit breakers, fuses and connectors. Chroma’s DC Electronic Loads are used for power testing in all markets including automatic test systems, LED, power supply testing, battery testing, and fuel cell testing. Chroma loads can do it all including full current down to 0.4VDC, CZ mode, user defined waveforms, timing measurements, and 3 current ranges per load. Chroma’s electronic loads come standard with either USB or RS232 ports for control and can be configured for GPIB (IEEE-488) control as well.
-
product
Surface Resistance Meter Kit - Test Anti-Static, Static Dissipative and Conductive Surfaces
PRS-812RM
- Surface Resistance Tester from 0.10 Ω to 1 Teraohm- Constant Voltages 10 volts and 100 volts- Automatic Electrification Period- Determines if a surface is Dissipative, Conductive, or Insulative- Measures resistance point-to-point(Rtt) and resistance to ground (Rtg)- Measures resistance of ESD Flooring, ESD Worksurfaces and Packaging- Conforms to all ESD Association Standards for Resistive Characterization- Includes 2 each Surface Resistance Probes- Packaged in a hard shell Carrying Case- Certificate of Calibration Traceable to NIST included- 2-year Limited Warranty on Main Instrument
-
product
Ground Earth Resistance Tester
2678X
Shenzhen Chuangxin Instruments Co., Ltd.
Ground Earth Resistance Tester verifies the integrity (continuity) of the protective bonding of the equipment (Class I equipment) designed to secure safety through the basic insulation and protective earthing. It is also called earth (ground) bonding test. If the continuity of the protective bonding is confirmed, we can conclude that the equipment has the requirements for preventing electric shock even if the insulation between the primary circuit and the accessible conductive section fails and a fault current flows through the distribution system.
-
product
Load tester for JA and C Type Durometers
It is necessary to check the shape and height of the indentor, the indicating mechanism, and other parts of the hardness tester are set correctly before doing a load test.
-
product
AC Load Bank
AC-LB-Series
Eagle Eye AC Load Banks are commonly used for testing generator sets, UPS units, aircraft power inverters and other government and military AC power sources. The Eagle Eye AC LB-Series is the smallest in the industry and offers unmatched durability in even the harshest testing environments. Eagle Eye offers several standard models as well as custom AC Load Banks.
-
product
Low Profile Compression Only Load Button Load Cell with Mounting Holes
LBC SERIES
The LBC Series (Load Button) load cells are offered for compression only applications where space is limited. The matching surface must be flat and at least the diameter of (D1). The loading diameter (D2) is slightly convex for accurate load distribution. Counter bored mounting holes are provided for fastening down from the top. These sensors are manufactured from heat treated 17-4ph stainless steel and sealed for use in most industrial environments.
-
product
Electronic Load
* Fully programmable, self-contained, air-cooled solid state load.* Patented design is optimized to provide ultra-low impedance operation for fuel cell testing.* Load is compatible with AC impedance or frequency response analyzers.* Interchangeable shunts for precise operation over a wide dynamic range.* Ten built-in cell voltage monitoring inputs optional. Additional voltage monitoring inputs available.* Ethernet Interface for simple configuration and expansion!* Combine with additional Fideris™ Innovator Series™ modules to create a fully-integrated,fully-automated, customized test system.* System-wide control of all Fideris™ Test System Components using FCPower™ Software,LabviewTM, or other programming language.* Integrated hardwired Run/Standby signal.
-
product
AC Electronic Load
AC&DC Electronic Loads are design for testing uninterruptible power supplies(UPS), Off-Grid Inverters, AC sources and other power devices such as switches, circuit breakers, fuses and connectors.
-
product
Electrometer / High Resistance Meter, 0.01fA, Battery
B2987B
The B2987B Electrometer/High Resistance Meter is the world’s only graphical electrometer that allows you to confidently measure small currents with 0.01 fA (0.01 x 10-15 A) resolution and large resistances of up to 10 PΩ (10 x 1015 Ω). In addition, battery operation eliminates AC line noise from your critical measurements.
-
product
Resister Blackjack
Resistor blackjack is like regular blackjack but better! Your goal is to assemble a single resistance from several resistors that is as close to 21k while not being over.Unlike regular blackjack, the resistors can be combined in series and in parallel, giving the game a whole new dimension. Plus, resistors have tolerances so achieving a mathematical 21k doesn't guarantee a win.
-
product
Resistivity Meters
DDR3
Integrated Geo Instruments & Services Private Limited
The DDR 3 Resistivity Meter is a specialized version of IGIS Resistivity meters designed for use in Resistivity surveys up to about 200m depth. It utilizes rechargeable batteries as power source to energize the ground thus eliminating the necessity of using the relatively expensive dry cells.
-
product
Handheld Digital Multimeter, 4.5 Digit, Water and Dust Resistant
U1272A
Feature sets that meet traditional industrial requirements and improve productivity and safety Improved accuracy and resolution to meet traditional industrial requirements (30,000 counts resolution with 0.6% for ACV accuracy)Intelligent features to improve productivity and safety (LPF, ZLOW, Smart )Better grip Both visual and audible continuity indication in noisy environments Easy access to fuse for simplified maintenance Easy connectivity to PC and internal memory (up to 10,000) for data logging Large rotary switch and buttons that are easy to operate Dust and water resistant casing (IP 54 compliant)Compatible with U1177A/U1117A IR-Bluetooth adapter for remote monitoring & datalogging Altitude: 3000 meters
-
product
Programmable DC Load Current Waveform Generator
9923
9923 application software can be used to edit arbitrary waveform, providing electronic load simulation different sink current conditions
-
product
20/26 GHz Coax, Insert, Receiver, SIM, 2 POS, 6 Slot (not loaded)
510180110
20/26 GHz Coax, Insert, Receiver, SIM, 2 POS, 6 Slot (not loaded)20/26 GHz Coax patchcords need to be purchased separately.
-
product
S-Type Load Cells
S-Type load cells are low-cost and high performance side mounted load cells suitable for a number of weighing and general force measurement applications. They come with a 6-foot strain relieved integral cable with pigtail leads that are stripped and tinned for electrical interface.
