PMC Adapters
Computer boards that translate the data from the PMC bus to another bus and vice versa. They are used to connect two incompatible buses. (globalspec.com)
-
Product
Flexible MiniPCI Express to PCI Adapter
SKU-034-0X
-
Flexible MiniPCI Express to PCI Bus Adapter (Adapter) was designed to convert the MiniPCI Express bus into two 32-bit PCI buses. It allows to connect up to 2 32-bit PCI expansion boards to the motherboard MiniPCI Express connector (supports full-size and half-size MiniPCI Express host boards).Adapter includes a PCI adapter, MiniPCI Express host board (full-size or half-size) and PCI Express flat Cable.
-
Product
Tool, Extraction, 90 Series Modules, Interconnect Adapters
910109111
Extraction Tool
Tool, Extraction, 90 Series Modules, Interconnect Adapters
-
Product
PMC Carrier for PCI Card Interface
TPCI270
-
The TPCI270 is a standard 33 MHz, 32 bit PCI carrier for a single PMC Card. Itprovides PMC front I/O and PMC P14 rear I/O. This PMC to PCI adapter is used to build modular, flexible and cost effective I/O solutions with PMC devices in standard PCI systems.
-
Product
EBIRST 78-pin D-type Coaxial Adapter - 37 SMBs
93-006-202
-
eBIRST adapters allow extension to other switching system connectors, including SMB
-
Product
Coaxial Waveguide Adapter, 1.85 mm (f), 40 to 60 GHz
U281A
-
The Keysight U281A adapter transforms waveguide transmission line into 50-ohm coaxial line. Power can transmitted in either direction, and each adapter covers the full frequency range of its waveguide band with SWR less than 1.3.
-
Product
Coax Module, ITA, 20/26 GHz, 17 Position. For use with 20/26 GHz ITA contacts with SMA adapter
510108240
ITA Module
For use with 20/26 GHz ITA contacts with SMA adapter.Primary mating module 510104287.
-
Product
Adapter, 50 Ohm Type-N (f) to 75 Ohm Type-N (m), DC to 3 GHz
11852B
-
The Keysight 11852B is an instrument-grade, 50-ohm type-N female to 75-ohm type-N male adapter. This product is also available in a 50-ohm type-N male to 75-ohm type-N female configuration. The 11852B Option 004 has a 50 Ohm Type-N (m) and 75 Ohm Type-N (f) connector.
-
Product
Adapter & DC Block
-
RF Lambda’s DC blocks are used to prevent DC signals from passing through a coaxial RF interface. They are low IL and wideband. RF Lambda’s line of adapters are used to connect RF signals using different connector options.
-
Product
XMC-to-PCI Express Adapter
4823
-
The Technobox, Inc. P/N 4823 XMC-to-PCI Express Adapter permits the use of a single-wide XMC module in a 1x PCIe slot. PCI express lanes on the P15 XMC connector are routed to the male PCI express edge finger connector. The reserved future use, RFU, signals from P15 are available on one of the user connectors. The adapter also provides user access to all the signals on the XMC P16 connectors via two 64 pin headers UC1 and UC2.
-
Product
Flexible PCI, PCI Express, Mini PCI, MiniPCI Express Adapters
-
Amfeltec Flexible PCI, PCI Express, Mini PCI, MiniPCI Express Adapters
-
Product
USB I2C Adapter
MS (Master & Slave)
-
*Plug & Play*No additional driver necessary*HID device drivers are included in major operating systems*Open interface description enables communication without a DLL
-
Product
32/64b 33/66 MHz PCI-x to PMC-x Adapter
8098a
-
The PCI-X to PMC-X Adapter permits operation of a standard 32 or 64 bit PCI-X card in a PMC-X slot while providing a migration path for PCI-X board suppliers to port their products to a PMC-X form factor.
-
Product
Electric Vehicle Charging Station EVSE Test Adapter
FEV100
-
Test the safety and performance of a type 1, level 1 or level 2 electric vehicle ac charging stations (EVSEs) with the Fluke FEV100. This test adapter simulates the presence of an electrical vehicle, allowing you to conduct tests in combination with appropriate test instruments such as a digital multimeter or oscilloscope.
-
Product
Adapter, 2.4 mm (f) to 3.5 mm (m), DC to 26.5 GHz
11901D
-
The Keysight 11901D is a metrology grade, 2.4 mm female to 3.5 mm male adapter with dc to 26.5 GHz operation.
-
Product
USB to TTL Adapter
SKU-012-0X
-
The USB to TTL adapter connects the Serial UART to the standard USB port for testing and monitoring functionality. The Adapter facilitates ease of use and helps to reduce board space and cost.
-
-
Product
Adapter Plate, iCon, Receiver, to NI PXI-1042
310113530
Receiver
Adapter Plate, iCon, Receiver, to NI PXI-1042.This adapter plate attaches directly to a NI PXI-1042 with portable monitor accessory (PMA-1115).
-
Product
2.92mm Adapters
-
Pasternack 2.92mm adapter category is mostly RoHS and REACH compliant. 2.92mm adapter components are part of a complete adapter product line from Pasternack. 2.92mm adapters in straight or right angle versions are in stock and ready for shipment.Our 2.92mm adapter series allow you to interface 2.92mm connectors with 1.85mm, 2.4mm, 2.92mm, 3.5mm, 7mm, Mini SMP, N or SSMA connectors. 2.92mm adapters are available in female to female, female to male, female to sexless, male to female, male to male or male to sexless gender combinations. The 2.92mm adapter category includes bulkhead, 4 hole panel or mountless configurations.Our ISO 9001:2008 registered facility ships 2.92mm adapter parts the same day from the broadest and deepest in stock inventory of RF and microwave parts. Exceptional customer service and technical support are on hand to help you.
-
Product
Adapter, 2.4 mm (m) to 2.4 mm (f), DC to 50 GHz
11900C
-
The Keysight 11900C is a metrology grade, 2.4 mm male to 2.4 mm female adapter with dc to 50 GHz operation.
-
Product
EBIRST 104-pin D-type To 100-pin SCSI Adapter Cable
93-022-245
-
The 93-002-245 104-pin to 100-pin eBIRST adapter cable is part of a range of USB controlled test tools capable of performing automated path resistance tests on Pickering Interfaces PXI, LXI or PCI controlled switching solutions. Each tool simply interfaces with the switching system's connector so a test can be run using the supplied Windows-based software.
-
Product
Serial Protocol Host Adapter
SPI Storm
-
This is the primary step for using SPI Storm device. It consists in describing how you would like to access your serial device: whether you would like to write to your device, read from it or do both simultaneously
-
Product
WAN Adapters
FarSync Flex
-
The FarSync Flex USB adapters have been developed to provide industry trusted sync and async communications support for Linux and Windows systems with multiple line signalling modes.
-
Product
Osprey PCI Unibus Adapter
9793
-
Dual-height card plugs into PDP-11 Unibus backplane. Fibrechannel cable plugs into Unibus logic connector on Osprey /TXP I/O Adapter logic provides Programmed I/O and DMA access to "real" Unibus compatible controllers (those not otherwise emulated).
-
Product
Adaptive Inverse for Actuator Compensation Toolbox
AIFAC
-
Actuator nonlinearities such as dead-zone, backlash, and hysteresis are ubiquitous in mechanical connections, hydraulic servo-valves, electric servomotors, piezoelectric, pneumatic and magnetic actuators, and even appear in biomedical systems. The Adaptive Inverse For Actuator Compensation (AIFAC) Toolbox for Simulnk allows control system engineers to design high-performance adaptive controllers to compensate for uncertain or undesirable actuator dynamics that would otherwise adversely affect closed-loop control system performance.
-
Product
2.92mm to ProLink Adapter with Probe Power and Communication Pass Through
L2.92A-PLINK
-
The Teledyne LeCroy LabMaster 10 Zi oscilloscope utilizes precision 2.92mm input connectors to achieve up to 36GHz of input bandwidth. But some applications may require the use of lower-bandwidth probes for performance and cost reasons.The L2.92A-PLINK adapter converts the 2.92mm interface to a ProLink interface. This brings the benefits of a wider selection of probes to the LabMaster 10 Zi such as Dx10/Dx20/Dx00A-AT 4-6 GHz differential probes and DH Series 8 to 20 GHz differential probes using the ProLink oscilloscope probe connection. Full probe power and control is provided through a built-in LEMO interface.
-
Product
XMC-to-PCI Express (PCIe) Adapter
9956
-
The Technobox XMC-to-PCI Express adapter with Rear I/O support permits use of a standard VITA 42.3 air-cooled XMC or VITA 20 conduction-cooled XMC in the smallest possible edge finger PCI Express form factor. The length of the adapter is the length of the XMC and 10 mm mezzanine stacking height is supported. The height is a standard PCI Express board and is not the low-profile version.
-
Product
COM Express Type 7 10GbE SFP+ Network Adapter Card
CEI-4x10G SFP+
Network Interface Controller
- Support up to four 10GbE SFP+ interfaces- COM.0 R3.1 Type 7 compliant- Dedicated for Express-ID7
-
Product
PCIe-to-MXM adapter supporting ADLINK Mobile PCI Express Modules with NVIDIA® Quadro® embedded GPUs
EGX-MXM-AD
-
The EGX-MXM-AD is an PCIe adapter supporting ADLINK NVIDIA® Quadro® MXM 3.1 Type A, Type B, and Type B+ GPU modules for quick validation and early development purposes on your AI applications. The following modules are supported: EGX-MXM-P1000, EGX-MXM-P2000, EGX-MXM-T1000, EGX-MXM-RTX3000, and EGX-MXM-RTX5000. A reference thermal solution is available.
-
Product
Adapter, 2.4 mm (m) to 3.5 mm (f), DC to 26.5 GHz
11901C
-
The Keysight 11901C is a metrology grade, 2.4 mm male to 3.5 mm female adapter with dc to 26.5 GHz operation.
-
Product
EBIRST 50-pin D-type To 2x8-pin Power D-type Adapter
93-005-236
-
eBIRST is a range of USB controlled test tools capable of performing automated path resistance tests on Pickering Interfaces PXI, LXI or PCI controlled switching solutions. Each tool simply interfaces with the switching system's connector so a test can be run using the supplied Windows-based software.
