.NET
software framework primarily running on Microsoft Windows.
-
Product
MIL-STD-1553 A / B Test And Simulation VXIbus Module
VXI-1553
-
*1, 2, 4 or 8 channels*Simultaneous bus controller, 31 remote terminals, bus monitor*Error entry and detection*FPGA based hardware architecture*Multi-level trigger for data acquisition and filtering*10 programmable, discrete I / O*IRIG-B timecode encoder / decoder with free-running mode*Real-time recording and physical bus playback*Supports: C, C ++, C # and .net*VISA based VXI Plug & Play driver*Optional twinax front end
-
Product
MIL-STD-1553 Test & Simulation Interface for VME
VME-1553
-
Avionics Interface Technologies
Dual redundant, single, dual, or quad stream configurationsTransformer & Direct Bus Coupling - Concurrent Bus Controller, 31 Remote Terminals, & Bus Monitor operation - Full error injection and detection - Multi-level trigger for capture and filtering - IRIG-B time code encoder/decoder - Ten high voltage (up to 30V) programmable DIO lines - Real-Time recording and physical bus replay - ANSI Application interface supporting C, C++, C#, and .NET development - Device driver support: Windows, Linux, & VxWorks (others on request) - Designed for extended temperature operations - 64-bit VME Interface (VME master & slave capability) - Front Panel and Rear I/O (P2) Available
-
Product
Three-Phase Network Analyzer
NET VISION 2010
-
NET VISION 2010 is a portable device designed for a quick and precise measurement of the electric values of a three-phase network. It is used by power engineers for check of AC motors, relay current protections, electricity meters, etc.
-
Product
One, Two, or Four Dual Redundant Interface MIL-STD-1553A/B Test & Simulation Module for PXI Express
PXIe-1553
-
Avionics Interface Technologies
1, 2, or 4 dual redundant MIL-STD-1553 bus interfaces Concurrent BC, multiple RT (31), and BM operations Full error injection and detection • Data capture filtering, 100% bus recording, and physical bus replay Multi-level Trigger for Capture/Filtering IRIG-B Time Encoder/Decoder Real-Time Recording and Physical Bus Replay Application interfaces supporting C, C++, C#, and .NET development Device Driver Support for: Windows, Linux, and LabVIEW Real Time (others provided on request) 10 high voltage (up to 30V) programmable DIO lines Flight Simulyzer GUI Analyzer software
-
Product
Optical Node
-
Sichuan Jiuzhou Electronic Technology Co.,Ltd
* Philips CGD914 amplifier module that employs both GaAs and Si dies.* 4 outputs, output level ≥100dBμV when optical input at -1dBm.* Plug-in fixed attenuator, fixed equalizer.* Optical power indication for -7 ~ 0dBm.* FP laser or DFB laser for return path.* RF test point for forward path and return path.* Optional SNMP responser unit supporting JIUZHOU HFC Net Managing software.* AC 60V or AC 220V power supply.* Aluminum die-casting housing.
-
Product
1149.6 Boundary Scan Feature, GTE 10.00p
K8213B
-
Keysight’s Interconnect Plus Boundary Scan 1149.6 feature enables all the tools required to develop and execute this test method on the board under test. Compared to the 1149.1 standards, the 1149.6 standards define test methods for the boundary scan devices that are designed with AC coupled signals or differential nets needed for high-speed operations of the device.
-
Product
Ion Chromatography
IC Software- MagIC Net
-
MagIC Net is the software to control your Metrohm ion chromatograph and any modules for liquid handling, sample preparation, and automation connected. Intuitive operation, comprehensive system monitoring, and straightforward data management make MagIC Net, what it is: the preferred software for state-of-the art ion chromatography.
-
Product
800MM 31.5In Digital Level Bevel Gauge w/ LCD Backlight Screen, Level Bubbles IP54 Standards
DL411
-
Advance Plus Trading Co., Ltd.
Model Number: DL411 Key Specifications/Special Features: 800MM 31.5INCH Digital Level with level bubbles, 2 hand shanks, LCD bright backlight display, IP54 standards 1. 800mm 31.5inch level with 2 bubbles, 800*28*64mm（L*W*H）, net weight: 700g;2. Resolution: 0.05°;3. Horizontal level measuring range: 0 to 360°;4. Accuracy: ±0.3°;5. Measures angle in degrees, IN/FT, mm/m, % slope or pitch;6. Audible tone at level, plump and setting angle;7. Automatic shut-off after 3 minutes;8. Backlight LCD;9. Self checking accuracy;10. Self calibration;11. Hold-function to freeze the measurement;12. Memory recall (9 measurements);13. 2pcs Handshanks design, easy to take and use;14. 2pcs high accuracy horizontal & vertical bubbles, clearly to check;15. Operated by DC 3V (2*LR03 AAA 1.5V batteries, not included); 16. IP54 waterproof & dusyproof industrial standard.
-
Product
Test & Measurement Services
-
We specialize in the development of advanced automatic test applications based on NI TestStand.- Development of NI Test Stand test programs, with code modules in LabVIEW, LabWindows/CVI, Measurement Studio/.NET, C/C++, and ActiveX/COM- Integration of test and measurement instrumentation, switching, and UUT bus interfaces- Customization of step types, process models, operator interfaces, reports, and databases- Integration in the enterprise software infrastructure (XML data formats, databases, web applications, etc.)- Integration of the NI TestStand ATML Toolkit
-
Product
C Series Current Input Module
Current Input Module
The C Series Current Input Module features programmable input ranges, variable connectivity options, and built-in noise rejection. You can also choose from options with built-in anti-aliasing filters or high-channel density to reduce the number of modules needed. The C Series Current Input Module supports safety features, certifications, input ranges, overvoltage ranges, and connectivity for applications such as power quality monitoring and metering, utility pole-mounted smart switches, utility pole-mounted smart grid reclosers, substation merging units, industrial machine measurements, health monitoring, predictive maintenance and prognostics, and phasor measurement units (PMUs). The C Series Current Input Module includes the NI-DAQmx driver and configuration utility that simplify configuration and measurements. NI-DAQmx supports NI programming environments as well as Python, ANSI C, C#.NET, and MathWorks MATLAB® software.
-
Product
Advanced Diagnostics for ScanExpress™ JET JTAG Embedded Test Solutions
ScanExpress JET Advanced Solutions
-
ScanExpress JET advanced diagnostics add additional diagnostic resolution with fully automated analysis translating functional test results to down to the net and pin level, even with BGA packages.The seamless integration with ScanExpress JET and ScanExpress Runner as well as the ability to output ScanExpress Viewer fault reports for PCB visualization make ScanExpress JET Advanced Diagnostics a must-have tool for any JTAG test system.
-
Product
MIL-STD-1553 A / B Test And Simulation VME Module
VME-1553
-
*Dual redundant*1, 2, 4 or 8 channels*Simultaneous bus controller, 31 remote terminals, bus monitor*Error entry and detection*FPGA based hardware architecture*Multi-level trigger for data acquisition and filtering*10 programmable, discrete I / O*IRIG-B timecode encoder / decoder with free-running mode*Real-time recording and physical bus playback*Supports: C, C ++, C # and .net*VISA based VXI Plug & Play driver*Optional twinax front end
-
Product
AFDX ® / ARINC 664 Test And Simulation PCI Module
PC104p-429
-
*4 or 8 software programmable TX / RX channels*Programmable high / low speed operation*Simultaneous operation of all TX / RX channels*128 MB RAM*Label selective triggering for recording / filtering*Real-time recording and later analysis of multiple channels*Sorting according to SDI field*VXI Plug & Play driver including soft front panel*Supports: C, C ++, C # and .net*Driver support: Windows, Linux, VxWorks and other systems
-
Product
C Series Digitizer Module
Digitizer
The C Series Digitizer Module takes both high-speed and high-resolution time- and frequency-domain measurements. It features up to four channels that can sample at speeds up to 20 MS/s—ideal for discrete detection of signals 10 MHz and smaller for applications such as fault detection, partial discharge analysis, and acoustic measurements. The module's store-and-forward architecture allows up to 128 Mbits of measurement data to be sent back to the CompactRIO Controller and analyzed. You can use the module as part of a CompactRIO system and use the LabVIEW FPGA Module to develop an advanced trigger based on low-speed streaming for added flexibility. This digitizer includes the NI-DAQmx driver and configuration utility that simplifies configuration and measurements. NI-DAQmx supports NI programming environments and Python, ANSI C, C#.NET, and MathWorks MATLAB® software.
-
Product
Unit Testing Mocking Solution for .NET
Suggest
-
Suggest creates automatic test suggestions suitable for your code.
-
Product
Online Audio Frequency Signal Generator
WavTones
-
We are proud to offer not only the best audio frequency signal generator on the net, but also a high-end sound generator, which compares favorably to the more expensive software and hardware tone generators!
-
Product
Fastest Flying Probe Test System for Semiconductor Substrate Interconnect Test
GATS-3200
-
* Test individual packages or * Test Multi-image panels with Step&Repeat Function * single flying probe top using very high speed voice coil motor (VCM) technology * 50 - 100 tests per second ... high throughput * Dual Flying Probe Top for testing bump-to-bump nets * flying probe head allows testing of all nets including each power and ground point * 4-wire test capability
-
Product
PC-NET Cable Tester
PR-09
-
The PC-NET Cable Tester is a portable, stand-alone unit that provides an affordable way to quickly test PC, Network, Telco, Coax, USB and IEEE1394 cables for continuity and wiring configuration for any combination. Open, shorts, miswires and cross-connected wires are detected immediately. The interchangeable connectors boards offers flexibility and convenience easy to read LED instantly indicates good or faulty. The tester is suitable for use by computer dealers and computer hardware outlets.
-
Product
ARINC 429 Test And Simulation PMC Module
PMC-429
PMC Module
*4, 8, 16 or 32 software programmable TX / RX channels*Programmable high / low speed operation*Simultaneous operation of all TX / RX channels*PXI interrupts, star trigger, and PXI clock*Error entry and detection*128 MB RAM*Label selective triggering for recording / filtering*IRIG-B timecode encoder / decoder for data correlation*Real-time recording and later analysis of multiple channels*Sorting according to SDI field*VXI Plug & Play driver including soft front panel*Supports: C, C ++, C # and .net*Driver support: Windows, Linux, VxWorks and other systems
-
Product
MIL-STD-1553 A / B Test And Simulation XMC Module
XMC-1553
-
*Dual redundant*1, 2 or 4 channels*Simultaneous bus controller, 31 remote terminals, bus monitor*Error entry and detection*FPGA based hardware architecture*Multi-level trigger for data acquisition and filtering*10 programmable, discrete I / O (up to 30V)*IRIG-B timecode encoder / decoder with free-running mode*Real-time recording and physical bus playback*Supports: C, C ++, C # and .net*Driver support: Windows, Linux, LabView Real-Time and other systems
-
Product
BSD (Test Diagnostics)
test
BSD Test Diagnostics software can be added to either developer or factory run-time systems to further improve the location of faults such as net bridges (short-circuits), open pins, open nets and even ''twisted'' connections that can occur within cable assemblies. BSD Test diagnostics reports faults in a verbose English language statement with pin level information included and can easily interpret multiple fault conditions.
-
Product
Digital Spectrometer
Pixie-Net
Spectrometer
The Pixie-Net is a multi-channel digital spectrometer for radiation detectors in desktop format with integrated processor, networking and USB resources.
-
Product
C Series Current Output Module
Input/Output Module
The C Series Current Output Module features up to eight channels of simultaneous analog output. You can choose between enclosed and non-enclosed modules. Additionally, the C Series Current Output Module has built-in open-loop detection. This detection generates an interrupt in software when an open loop is detected, zeros outputs to ensure safety, and avoids driving actuators at system power-on. The C Series Current Output Module requires an external power supply and includes a channel-to-earth ground double isolation barrier for safety and noise immunity.The C Series Current Output Module includes the NI-DAQmx driver and configuration utility that simplify configuration and measurements. NI-DAQmx supports NI programming environments as well as Python, ANSI C, C#.NET, and MathWorks MATLAB® software.
-
Product
Voltage Input Device For FieldDAQ
-
The Voltage Input Device for FieldDAQ measures up to eight ±10 V channels with 24-bit resolution and simultaneous sample rates up to 100 kS/s/ch. Some models can power sensors, such as pressure sensors, with up to 24 V per input channel. This device offers 500 V channel-to-channel isolation, protecting instrumentation from high-transient voltages. Additionally, the device is IP65 and IP67 rated to be dust-proof and water-submersible, can operate in -40 °C to 85 °C environments, and can sustain 100 g shock and 10 g vibration. It has an integrated network switch for simplified daisy chaining and provides tight synchronization over time sensitive networking (TSN) for distributed data acquisition systems.The Voltage Input Device for FieldDAQ includes the NI-DAQmx driver and configuration utility that simplify configuration and measurements. NI-DAQmx supports NI programming environments as well as Python, ANSI C, C#.NET, and MathWorks MATLAB® software.
-
Product
Hub of the System
Net-ESVR
-
The Enterprise Server NET-ESVR is a hub of the system. Its central role is to receive every 5 seconds the alarm status of each probe NET-XXX and to store the status and update system alarm matrix. It also provides communication with the multiple Clients NET-NMSC.
-
Product
IPTV Monitoring and Test Solutions
Net-x TVMS
-
The NET-xTVMS is a system of specialized computer probes networked to the enterprise server and clients. The probes, strategically located at the hub sites next to edge routers and edge QAMs, continuously monitor IPTV QoS with MPEG-TS transport metrics of SPTS and MPTS multicast streams as well as DVB-C MPTS streams. The NET-xTVMS is scalable from 1 to 1000 probes. Several types of probes are available to suit many different monitoring applications. Metrics are collected at the probes and alarms are sent to the server once they exceed predefined thresholds. A system wide alarm matrix, alarm logs and periodic metrics for each location can then be viewed via Internet on client computers.
-
Product
Open eVision Libraries
-
Hardware-independent image processing and analysis libraries for machine vision inspection applicationsCompatible with any image source, including frame grabbers, GigE Vision and USB3 Vision camerasSupport the latest technologies such as Deep Learning and 3DAccurate sub-pixel measurement and calibration64-bit and 32-bit libraries for C++ and .NET (C#, VB.NET, C++/CLI) under Windows64-bit libraries for Linux (x86-64)Easy to learn and useRobust, flexible and powerful
-
Product
Analyzer Probe
Net-200
-
The NET-200 B analyzer probe is an integral part of the NET-xTVMS, the real-time monitoring of IPTV services quality. Intended for locations at the core, edge, subheadend, etc., the NET-200B is designed to function autonomously for an extended period of time should communication with the NET-ESVR Enterprise Server be interrupted. The NET-200B is running under stable and safe Linux OS on server class computers, powered by AC or DC sources, with optional power redundancy.
-
Product
NR01 net radiometer
-
Hukseflux Thermal Sensors B.V.
NR01 is a market leading 4-component net radiation sensor, mostly used in scientific-grade energy balance and surface flux studies. It offers 4 separate measurements of solar and longwave radiation, facing both up and down. NR01 owes its popularity to its excellent price / performance ratio and major improvements relative to comparable instruments. These advantages include weight, ease of levelling, solar offsets in the longwave measurement and pyrgeometer heating, reducing measurement errors caused by dew deposition.
-
Product
Capaciter Tester
KS-1600
-
Konstar Electric Industrial Co., Ltd
It is a dial instrument, and has the stable function and high reliability. It is driven by the battery. The instrument makes use of the indicator plate(102*79mm), thus displays clearly.This instrument can test the data of on-line capacitive resistance and on line impedance. It is an excellent instrument and an ideal tool for the people in labs, factory and household. When testing the mounted capacitor, it does net need to be completely out of power nor do the meter, and the meter can be testing continuously.
