-
Product
TDR Structural Health Monitoring
-
Material Sensing & Instrumentation
MSI Time-Domain-Reflectometry (TDR) Structural-Health Monitoring probes the structural health of a composite part by propagating a fast electrical pulse along a distributed linear sensor which has been fabricated directly in the laminate. The sensor is formed from the native graphite fibers already used in composite manufacture, and constitutes zero defect. Fibers are patterned into a microwave waveguide geometry, or transmission line, and interrogated by a rapid pulse as shown below. Structural faults along the line cause distortions in waveguide geometry, producing reflected pulses similar to radar. Cracking, delamination, disbonds, moisture penetration, marcelling, and strain are all detected by propagation delay, for sensor lengths up to several meters.
-
Product
Enhanced Time Domain Analysis With TDR
S97011B
-
This application enables the analyzer to perform enhanced time domain analysis for high-speed data applications.
-
Product
TDR
-
Schonstedt offers a range of Radiodetection Time Domain Reflectometers (TDR), the perfect tools to quickly and accurately locate copper cable faults.
-
Product
TDR Cable Analyzer
CT100B
-
The CT100B is special for two reasons: (1) It is the industry''s only high-resolution portable TDR providing step TDR impedance waveforms with resolution sufficient to show connector detail (~1 cm), and (2) it is the industry''s first portable TDR capable of making frequency domain S-parameter measurements including return loss (S11) and cable loss / insertion loss (S21). "High resolution TDR is extremely useful for detecting and localizing cable faults and characterizing cable and connector performance, but historically, portable TDRs have been unable to display OSL-calibrated S-parameter measurements," said Brandt Mohr, MOHR chief technologist. "The CT100B includes that capability, making it a very versatile instrument. If you can only carry one cable tester out into the field with you, it should be the CT100B."
-
Product
TDR Concrete Cure Monitoring
-
Material Sensing & Instrumentation
MSI Time-Domain-Reflectometry (TDR) Concrete Cure Monitoring provides a new approach to cure monitoring in concrete and cementitious materials [1-7]. Using an ultrafast pulse and inexpensive capacitance sensor, our TDR system follows rotation of individual chemical states of water participating in the hydration reaction. The system monitors formation of bound-water hydration products, as well as unreacted free-water to form the hydrated state.
-
Product
Enhanced Time Domain Analysis With TDR
S93011B
-
S93011B enhanced time domain with TDR is available on all PNA models (N52xxB) and provides a one-box solution for high-speed interconnect analysis, including impedance, S-parameters, and eye-diagrams
-
Product
Differential TDR, 35 ps, 15 GHz, ESD, Sxy, OSLT 3.5MM Cal Kit, Aluminum Case, Internal Battery
T3SP15D-B-BUNDLE
-
Differential TDR,35ps Rise Time, ESD protection,2 phase matched 3.5mm cables,3.5mm Cal. Kit, Battery.
-
Product
DR software, for use with CT100 Series TDRs
CT Viewer™
-
CT Viewer™ is a full-featured TDR waveform analysis software package for Microsoft® Windows® XP / Vista PCs that lets you archive, manipulate, analyze, and compare TDR data acquired with CT100 Series Automated Metallic TDRs or any other TDR instrument, now with live internet streaming and remote control of CT100 Series TDRs. CT Viewer™ is included with CT100 Series TDRs. Read on to discover how CT Viewer™ will change the way you test cables.
-
Product
Pre- Locator
CFL PL4
-
CFL PL4 Power Cable Fault Locator is a portable, easy to use cable fault pre-location instrument. It uses the Time Domain Reflection (TDR), Secondary Impulse Method / Multiple Impulse method (MIM) and Impulse Current Method (ICM) on low, medium and high voltage cables. Its measuring ranges enable pre-location on cable lengths from 500 m to 64km.
-
Product
CATV Meters & Instruments
-
GAOTek offers high quality, affordable CATV meters and testers to industry engineers. These instruments are used by professionals to automatically or manually test, measure, and maintain a wide collection of systems and channels. Our products are portable and durable to ensure long operational use during everyday field use by CATV technicians. Additionally, we offer QAM analyzers, PCM channel analyzers and TDR cable fault locators.
-
Product
DCA-X Sampling Oscilloscopes
-
The DCA-X wide-bandwidth sampling oscilloscopes are in our digital communication analyzer (DCA) family. These are modular platforms that provide accurate and precise measurements of high-speed digital designs from 50 Mb/s to 224 Gb/s. You can configure the DCA-X mainframes by selecting from a variety of plug-in modules that perform precision optical, electrical, and time domain reflection / transmission (TDR / TDT) measurements. Select specific modules to obtain the desired bandwidth, filtering, and sensitivity that match your measurement needs.
-
Product
Multi-function Cable Tester
NCT-100-S
-
*NCT-100-S Multi-Function Cable Tester Kit can help you quickly find network cables with OOK audio during network construction and maintenance. *Use TDR diagnostic technology to quickly and accurately locate fault points and accurately measure wiring diagrams and lines. Cable identification, etc.
-
Product
Voyager Intermittent Fault Detector
-
The Voyager includes a spread spectrum TDR so that the fault can be located. Once an intermittent is detected, the TDR is immediately connected to the failed test point and used to determine the distance to the fault.
-
Product
Intelligent Cable Fault Locator
TM800
-
TM800 Cable Fault Locator is a portable field instrument working on TDR and bridge methods, adopting advanced micro-electronics technology. It is designed to locate accurate fault points in such cables as telecommunication leadsheathed cable, plastic cable or user’s lead covered wire, while the faults include break, mix, earthing, defective insulation, or poor connecting. It is and ideal function-stable instrument for the field operator to improve work efficiency, in addition, it can also be used for circuitry project checking electric property testing of the cable.
-
Product
Time Domain Reflectometers
-
Locating high and low impedance faults on paired metallic cables is a crucial yet often difficult task for a telecoms engineer. Megger designs TDRs specifically for the communications industry, which makes each unit a safe, application specific tester that can be used on virtually all communications cable types. The wide range of TDRs makes it easy to choose the tester with the resolution and range you need.
-
Product
Cable Fault Locator-TDR
TM800N
-
TM800N Cable Fault Locator (hereinafter to be referred as TM800N) is used for test est cable break, short circuit faults of telephone cable, data cable, high frequency cable, coaxial cable,and so on.
-
Product
Impedance Measurement
CITS880s
-
Finer geometries and thinner copper can present a challenge for fabricators measuring impedance on leading edge PCBs. The CITS880s answers that challenge with the introduction of Launch Point Extrapolation (LPE). LPE extrapolates the TDR response back to a point close to the start of the transmission line effectively allowing to users more accurately to measure the instantaneous or incident impedance of the line.
-
Product
TDR Composite Cure Monitoring
-
Material Sensing & Instrumentation
MSI Time-Domain-Reflectometry (TDR) Composite Cure Monitoring [1-4] provides a new approach to cure monitoring of advanced polymer composites. Using a high-speed pulse and inexpensive microwave sensor, our TDR system follows rotation of a polar resin molecule, providing real-time information on viscosity and percent cure. Operating in the microwave frequency range, TDR Cure Monitoring provides an alternative between high-frequency fiber-optic methods and low-frequency dielectric methods, combining optical-style precision and miniaturization with electrode-based simplicity and robustness.
-
Product
Signal Integrity Test Products
RoBAT SCARA-TDR-M
-
*Fully automatic TDR tester for bare and assembled PCBs*2 – 24 Port Ultra-compact TDR units*Full range of TDR tests and measurements available*100% test in a production environment*Custom modules with automatic tool changer
-
Product
Cable Scanner
MI 2014
-
Cable Scanner is easy to use LAN tester with wide variety of functions for fault finding and troubleshooting on IT cabling connections. TDR facility with adjustable NVP allows determination of distance to the fault or cable length measurement. Acoustic generator combined with a receiver enables pair determination in multi-pair cables.
-
Product
Cable TV
-
Tempo Communications provides technicians with an array of test and measurement solutions to optimiz... e the installation and performance of broadband cable networks. The tried-and-true TDR from Tempo delivers all of the enhanced features required to pinpoint faults and verify performance. Like all of its test and measurement devices, the focus is on reliability, ease-of-use, and quality—empowering technicians to do their jobs and exceed customer expectations.Show less
-
Product
TDR Test System
GATS-310
-
The GATS-310 TDR test system provides you with the ability to test nets as down to less than 1/2" in length using Industry Standard Techniques.
-
Product
TDR Test Set
TS® 54
-
Fluke Networks’ new TS52 PRO Test Set features the latest in test set technology. Designed with a superior, radiant liquid crystal display (LCD) user interface, it allows you to see what cannot be heard in any outside plant environment.
-
Product
Three-Dimensional Electromagnetic Simulation Package
QuickWave-3D
-
QuickWave 3D (QW-3D), is a universal user-friendly three-dimensional electromagnetic simulation package (winner of the European Information Technology Prize in 1998) based on the conformal FDTD method and supplemented with a range of unique models for curved boundaries, media interfaces, modal excitation, and parameter extraction. Complete 3D electromagnetic simulation offer a set of various results from wide area of applications. A lot of processing/postprocessings present a complete offer of comprehensive solutions from microwave components (filters, couplers, resonators, etc.) through antennas, TDR applications, optimisation and parameters sweep to simulation of microwave heating process (with Basic Heating Module) with temperature dependent media, static, rotated or moved heated object(s), and heat transfer.
-
Product
Signal Path Analyzers
HL5200 Series
-
HYPERLABS HL5200 Series Signal Path Analyzers™ provide ESD-robust, multi-channel test and measurement capabilities for a fraction of the cost of traditional benchtop systems. These differential instruments have up to 20 channels and can be used to take TDR, TDT, and XT (crosstalk) measurements. Beginning in June 2015, S-parameter (S11/S21) data will also be available.
-
Product
Cable Fault Locator
FaultCaster
-
Low Cost Full specification Professional Digital TDR Measures Distances to Open or Short Circuit Faults Extended Measuring Range to 2000m (6000ft) on all cable types Fast-Edge Step TDR technology for improved range & Resolution
-
Product
Oscilloscopes
PicoScope 9000 Series
-
Up to 25 GHz bandwidth9.5 GHz optical input40 ps Differential TDR / TDT sourceSequential sampling Oscilloscope
-
Product
Guided Wave Radar Level Transmitter
2291
-
The 2291 Guided Wave Radar level transmitter is designed for continuous level measuring of conductive or non-conductive liquids, pulps and solids. The 2291 level gauge operates based on the well-known TDR (Time Domain Reflectometry) principle. Micropulses are sent along a probe guide at the speed of light. As soon as the impulse reaches the surface of the medium, it is reflected back to the electronic module. Level distance is directly proportional to the flight time of the impulse.
-
Product
Cable Testers
-
The Tester can check UTP and STP Cat 5E,6,6A and Coaxial Cable. It can ldentify and locate the distance of a open or Short Circuit. With the Multifunction Tester you can determine the Continuity and Wiring of the Cable Pattern. Comes with the Low Battery Indicator. It uses TDR ( Time Domain Reflectometer ) to measure the length and distance of the cable. LCD Backlight Display.There are 8 Remote ID available.
-
Product
MPI PCB Probe Systems
-
MPI Advanced Semiconductor Test
Every MPI manual probe systems can be configured with a variety of different holders for printed circuit boards (PCB’s) in order to provide in addition to on-wafer, versatile, convenient, and accurate Signal Integrity (SI) measurements with single-ended or differential RF probes. Measuring signals at the end of the channel for eye-patterns, deterministic jitter, distortion, TDR (Time Domain Reflectometry) impedance, cross-talk, coupling, and losses, or even S-parameters is easily accomplished.
