Synchronization
See Also: Synchronizers
-
Product
4 Serial Communication Channels, Multi-Mode Programmable, Non-Isolated
SC7
-
Module SC7 supports intelligent, full duplex, independent, multi-channels that can be individually software-configured for either RS-232C, RS-422, RS-485, RS-423 (w/data and/or clk bit inversion for MIL-STD-188C unbalanced interface support), or synchronous or asynchronous communications. SC7 is the same as SC1 except SC7 reallocates the pins used for CTS Flow Control as four (4) additional system grounds.
-
Product
FD-11634, 8-Channel Sound and Vibration Input Device for FieldDAQ
786471-01
-
The FD-11634 can measure signals from integrated electronic piezoelectric (IEPE) and non-IEPE sensors such as accelerometers, tachometers, and proximity probes. The device also works with smart TEDS sensors, delivers a wide … dynamic range, and incorporates software-selectable AC/DC coupling and IEPE signal conditioning. The input channels simultaneously measure signals and have built-in anti-aliasing filters that adjust to your sample rate. This device is IP65/IP67-rated to be dust-tight and water-submersible and can sustain 100 g shock and 10 g RMS vibration in -40°C to 85°C environments. You program the FD-11634 with NI-DAQmx, which automatically synchronizes multiple FieldDAQ™ devices. When used with NI software, this device can provide processing functionality for condition monitoring such as frequency analysis and order tracking.
-
Product
Reduced Voltage Motor Starting Panels by Auto-Transformers
-
Reduced Voltage Motor Starting Panels are designed for starting of squirrel cage induction and synchronous motors. A RVMS Panel reduces the torque by temporarily reducing the voltage and/or current input. It reduces voltage applied to the motor during start up causing lower starting currents from the connected grid.
-
Product
Low Power FPGA Featuring Hardened MIPI D-PHY, LVDS, SLVS, SubLVDS, & Open LDI Bridging
CrossLink
-
*Two 4-lane MIPI D-PHY transceivers at 6 Gbps per PHY*15 programmable source synchronous I/O pairs for camera and display interfacing*Available in amazingly small 2.46 mm x 2.46 mm WLCSP packages and BGA packages with 0.4 mm, 0.5 mm and 0.65 mm pitch
-
Product
PXIe-5668, Up to 26.5 GHz PXI Vector Signal Analyzer
783156-03
-
Up to 26.5 GHz PXI Vector Signal Analyzer - The PXIe‑5668 offers wide bandwidth with high-performance measurement performance and speed. It meets the challenging requirements of applications such as wireless communications, radio frequency integrated circuit characterization, RADAR test, and spectrum monitoring and signal intelligence. With its implementation as a PXI instrument, the PXIe‑5668 also features the fast measurement speed required for high-volume manufacturing test, and multi-instrument synchronization capabilities for phase-coherent MIMO test. You can use the optionally included PXIe-5698 preamplifier to improve dynamic range and sensitivity near the instrument noise floor.
-
Product
USB Products
-
Keysight´s compact USB modular products are a series of modules that are flexible to be used standalone or plugged into a compatible chassis to make synchronized measurements as a modular unit. Essential measurements can be made with a laptop PC and these modules through USB high-speed 2.0 connections. Through individual windows, the Keysight Measurement Manager (AMM) software provides a friendly soft front-panel interface for each of the modular products. This helps to perform quick configuration and measurement acquisition as well as flexible analysis of measured data.
-
Product
LVDS Board
MSXB 045
-
The MSXB 045 LVDS board works with multiple iDSC 1816 boards to provide synchronization for many channels of data. An MSXB 045 board in each of two or more networked PCs, that each contain one or more iDSC 1816 boards, allows the whole networked system to work as a single synchronized system with possibly hundreds of conditioned channels.
-
Product
Multi-Spectral UV/Laser Range Stimulator
Phantom™
-
The Phantom is a long-range laser and ultraviolet (UV) stimulator capable of testing aircraft electro-optical sensor suites up to 5 km. Phantom can operate as an independent laser and/or UV stimulator or can be integrated with our other electro-optical and radio frequency range systems (see GTESS and PRTS). The Phantom provides both a laser threat and a synchronized temporal missile plume signature to stimulate both the aircraft’s laser and missile warning systems. Training aircrew to counter maneuver a Laser Beam Riders (LBR) threat is considered essential to survival and in-air training. The Phantom can be deployed either on a shoulder or tripod mount.
-
Product
PXI-5421, 43 MHz Bandwidth, 16-Bit PXI Waveform Generator
778697-02
-
43 MHz Bandwidth, 16-Bit PXI Waveform Generator—The PXI‑5421 is a 43 MHz arbitrary waveform generator capable of generating user-defined, arbitrary waveforms and standard functions including sine, square, triangle, and ramp. This arbitrary waveform generator can generate signals from -6 V to +6 V and uses direct digital synthesis (DDS) to precisely generate waveforms. The PXI‑5421 also features advanced synchronization and data streaming capabilities.
-
Product
Antenna-integrated PTP Grandmaster Clock
OTMC 100
-
OTMC 100 antenna-integrated PTP Grandmaster Clocks provide you with a quick and easy solution to time synchronize inteligent electronic devices, computers and measurement equipment connected via Ethernet.
-
Product
Solid State Recorder
MS 2001
-
This system is used to acquire Bi phase and DM signals from aircraft and records into FLASH memory. System has automatic frame synchronization and it is achieved through in built hardware circuit.
-
Product
2-Channel 3.6 GHz or 4-Channel 1.8 GHz 12-bit A/D with DDC - 6U VPX
Model 58741
-
- Supports Xilinx Virtex-7 VXT FPGAs- GateXpress supports dynamic FPGA reconfiguration across PCIe- One or two 1-channel mode with 3.6 GHz, 12-bit A/Ds- Two or four 2-channel mode with 1.8 GHz, 12-bit A/Ds- Programmable one- or two-channel DDCs (Digital Downconverters)- 4 or 8 GB of DDR3 SDRAM- µSync clock/sync bus for multiboard synchronization- PCI Express (Gen. 1, 2 & 3) interface up to x8- Optional user-configurable gigabit serial interface- Optional LVDS connections to the Virtex-7 FPGA for custom I/O- Ruggedized and conduction-cooled versions available- Supports GateXpress® FPGA-PCIe Configuration Manager- Synchronize up to twelve modules with Model 9192 System Synchronization and Distribution Amplifier- 1U Rack-mount
-
Product
Synchronized Power Measurements
-
Built for progressive electric industry professionals, Models 1133A and 933A support Synchrophasors, Power Quality Monitoring, System Control and Monitoring, GPS Synchronization, Revenue Metering, Data and Event Logging and related technologies in a single package.
-
Product
IRIG Time Code Receiver & Generator for Computers (PCI Express)
TCR180PEX
-
Meinberg Funkuhren GmbH & Co. KG
The TCR180PEX receives IRIG-A/B/G, IEEE 1344, IEEE C37.118 or AFNOR NF S87-500 time codes and can be used for synchronizing the system time of its host PC. The IRIG output of this card can generate an IRIG signal for other IRIG time code readers. The output format is independent from the incoming IRIG signal - a perfect solution to your IRIG conversion requirements. It is used in applications like data acquisition, standalone computer time synchronization (for systems without a network connection or higher accuracy requirements) or as an IRIG converter device.
-
Product
Ethernet/LXI digitizerNETBOX 14 Bit High Speed Digitizer - 400 MS/s on 2 Channels, 2 Single-Ended Inputs
DN2.448-02
-
The digitizerNETBOX DN2.44x series allows recording of one, two, four or eight synchronous channels with sampling rates of 130 MS/s up to 500 MS/s. These products offer outstanding A/D features in resolution, bandwidth and speed as a remote instrument. The powerful A/D amplifier section offers six different input ranges, two input paths, AC/DC coupling and noise reduction filters.
-
Product
6-Ch 200 MHz A/D with DDC & 4-Ch 800 MHz D/A with DUC, Virtex-7 FPGA - 6U VPX
Model 58721
-
- Supports Xilinx Virtex-7 VXT FPGAs- GateXpress supports dynamic FPGA reconfiguration across PCIe- Three or six 200 MHz 16-bit A/Ds- Three or six multiband DDCs- One or two DUCs- Two or four 800 MHz 16-bit D/As- Multiboard programmable beamformer- 4 or 8 GB of DDR3 SDRAM- PCI Express (Gen. 1, 2 & 3) interface up to x8- Optional LVDS connections to the Virtex-7 FPGA for custom I/O- Ruggedized and conduction-cooled versions available- Supports GateXpress® FPGA-PCIe Configuration Manager- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Product
PXI Switch - 16-CH General-Purpose SPDT Relay Module
PXI-7901
-
ADLINK PXI-7901 is a general-purpose (GP) switch module implementing 16-CH independent single-pole double-throw (SPDT) relays (1 Form C). PXI-7901 can connect one input to one output and be used as signal switching and routing for measurement system or ATE. Thanks to its high switching capacity, PXI-7901 can also be used to turn on or turn off devices such as motors, fans, heaters, and lights. The contact position of the relays can be changed either by direct software commands or by following the instructions previously stored in the on-board scan list. The scan list advances upon the trigger from external measurement devices, such as a DMM. The scan list could also advance when the scan-delay timer expires. In the PXI-7901, PXI trigger functions are supported and software programmable. Multiple modules can therefore be synchronized without additional field wiring.
-
Product
Secondary Injection Test Set
PTE-100-C Pro
-
The values which are presented in the LCD display are highly accurate, easy to read, and independent of the injection made by the PTE-100-C base unit.The display shows continuously the phase difference between the voltage and the current injected, and can be adjusted during the test with an accuracy of 0.1º. This facilitates the test for directional relays or reclosers and synchronizing relays, etc.
-
Product
Ethernet/LXI digitizerNETBOX 16 Bit High Speed DIgitizer - 250 MS/s on 12 Channels, 12 Single-Ended Inputs
DN6.442-12
-
The digitizerNETBOX DN6.44x series allows recording of up to 24 synchronous channels with sampling rates of 130 MS/s up to 500 MS/s. These products offer outstanding A/D features in resolution, bandwidth and speed as a remote instrument. The powerful A/D amplifier section offers six different input ranges, two input paths, AC/DC coupling and noise reduction filters.
-
Product
Digital Relay and Merging Unit Tester
POM2-3333
-
POM2-3333 Digital Relay and Merging Unit Tester is equipped with 6*12.5A and 6*120V outputs, 8 pairs of BI, 4 pairs of BO and 6 fiber optic ports, built-in GPS, supporting PPS, IRIG-B, PTP/IEEE1588 time synchronization.
-
Product
Linking Conveyor 765mm
AM307
-
The high performance linking conveyor from 6TL is an option for the users of 6TL36 handling technology. The 6TL36 needs a high performance conveyor in the inlet, that is able to synchronize with the conveyor inside the handling system, so that the UUT can be stopped without phisical stopper, to further proceed with the contacting operation.
-
Product
JR-1
12820
-
• 35 Amp relay [@ 24VDC max. or @ 48VAC max.]• Crystal controlled timing• Rechargeable battery• Immediate or delayed interruption operation• Low battery indicator• Countdown and relay status indicators• On and off cycle times up to 999.9 seconds• Synchronized operation with any number of JR-1's and JR-2's
-
Product
Optical Power Meter
SAT-7E PON
-
Shaanxi Aitelong Technology Co., Ltd
SAT-7E PON power meter is a special tester to test FTTx/PON passive optical network, it can synchronously measure voice, data and video signal on BPON/EPON/GPON framework. It also can set the power threshold and indicate the pass, alarm and fail of every wavelength.
-
Product
FMC-HPC ADC Board
FMC123
-
Sundance Multiprocessor Technology Ltd.
The FMC123 provides four 16-bit A/D channels up to 1Gsps. The design is based on Texas Instruments’ ADS54J60 Analog-to-Digital converter. The sample clock can be supplied externally through a coaxial connection or supplied by an internal clock source (optionally locked to an external reference) for multi-channel synchronization. An external trigger input is available for timing synchronization. The FMC123 is mechanically and electrically compliant to the FMC standard (ANSI/VITA 57.1).
-
Product
PXI-5152, 300 MHz, 2 GS/s, 8-Bit PXI Oscilloscope
779772-03
-
300 MHz, 2 GS/s, 8-Bit PXI Oscilloscope—The PXI‑5152 high-speed PXI oscilloscope has two channels with flexible settings for coupling, impedance, voltage range, and filtering. PXI Oscilloscopes also feature a number of triggering modes, deep onboard memory, and an instrument driver that includes data streaming and analysis functions. This device is ideal for applications with fast signals that require up to 300 MHz of analog bandwidth and flexible measurement configurations. The PXI‑5152 also features PXI synchronization and data streaming capabilities.
-
Product
Dynamic UPS
ROTOBLOC® RBT SERIES 400 - 2000 kVA
-
The RBT system consists of a standard synchronous generator with no special windings and a simple steel flywheel. The low speed shaft extends bearing life and reduces maintenance. The ROTABLOC® machine is very robust as critical functions do not use fragile components such as power electronics, power capacitors, electro-chemical batteries, active magnetic bearings, electro-mechanical or mechanical friction clutches.
-
Product
PXI-5122, 100 MHz, 100 MS/s, 14-Bit PXI Oscilloscope
778756-02
-
100 MHz, 100 MS/s, 14-Bit PXI Oscilloscope—The PXI‑5122 high-resolution PXI oscilloscope has two channels with flexible settings for coupling, impedance, voltage range, and filtering. PXI Oscilloscopes also feature a number of triggering modes, deep onboard memory, and an instrument driver that includes data streaming and analysis functions. This device is ideal for both time-domain and frequency-domain applications that require high-resolution, low-noise measurements with up to 100 MS/s and 100 MHz of analog bandwidth. The PXI‑5122 also features PXI synchronization and data streaming capabilities.
-
Product
3-Channel 200 MHz A/D and 2-Channel 800 MHz D/A with Virtex-6 FPGA - 6U VPX
Model 57620
-
- Complete radar and software radio interface solution- Supports Xilinx Virtex-6 LXT and SXT FPGAs- Three 200 MHz 16-bit A/Ds- One DUC (digital upconverter)- Two 800 MHz 16-bit D/As- 2 GB of DDR3 SDRAM; 32 MB of QDRII+ SRAM- PCI Express (Gen. 1 & 2) interface up to x8- Sample clock synchronization to an external system reference- LVPECL clock/sync bus for multiboard synchronization- Optional user-configurable gigabit serial interface- Optional LVDS connections to the Virtex-6 FPGA for custom I/O- Ruggedized and conduction-cooled versions available- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Product
PXI-7854, Virtex-5 LX110 FPGA, 750 kS/s PXI Multifunction Reconfigurable I/O Module
780342-01
-
Virtex-5 LX110 FPGA, 750 kS/s PXI Multifunction Reconfigurable I/O Module—The PXI‑7854 features a user-programmable FPGA for high-performance onboard processing and direct control over I/O signals to ensure complete flexibility of system timing and synchronization. You can customize these devices with the LabVIEW FPGA Module to develop applications requiring precise timing and control such as hardware‑in‑the‑loop testing, custom protocol communication, sensor simulation, and high-speed control. The PXI‑7854 features a dedicated A/D converter (ADC) per channel for independent timing and triggering. This design offers specialized functionality such as multirate sampling and individual channel triggering, which are outside the capabilities of typical data acquisition hardware.
-
Product
9GS/s 16Bit 8GS Mem 12CH 24 Markers RF AWG Benchtop
P94812B
-
The benchtop version of the Proteus arbitrary waveform generator series offers up to 12 channels in a 4U, 19” benchtop box. With a 9” touch display and on-board PC the benchtop platform enables users to program the instrument without the need of an external PC. Users can program the instrument from the onboard PC using various programming environments such as MATLAB, LabView, Python, and more. So for synchronized, phase coherent, multi-channel applications such as quantum physics and radar applications the Proteus arbitrary waveform transceiver is an ideal, high performance, and cost effective solution.
