Wiring
See Also: Wiring Analyzers, Trailer Harness Testers, Harness
-
Product
CATx Surge Protector
SP-CAT5-6V
-
Protects sensors running on CATx unshielded twisted pair (UTP) cable against the effects of electrostatic discharge, faulty wiring and lightning. The use of two protectors on each end of the line will provide increased protection for each end against surges. Protected pins: (1,2) (3,6) (4,7) and (7,8) pass through. Impedance: 85 to 115 Ohms. Surge suppression: 22Vpeak @ 100A 10/1000µs. Maximum continuous voltage: 6Vpeak. Dimensions WxDxH: 1x3.6x0.9 in (25x91x23 mm). Regulatory approvals: GR 1089, NEC 800.100 and 830.100, ITU 703, UL94 V0 Flame Rated.
-
Product
AC/ DC mA Current Clamp-on Transducer
CA-60
-
This miniature clamp meter features two Hall effect sensors. For use with any multimeter with 200mV or/and 2V ranges for direct readout input impedance of least 1M ohm. High conversion factor for low DC and AC mA measurement. With the small jaw size it can fit into tight space in circuit panel or wire bundle to take the reading.
-
Product
Cable Assembly, 9-Pin D-Type Female to Unterminated With Tinned Ends, 0.5m, HV
A009DF4-T-HA050
Cable Assembly
A range of 9-Pin D-Type High Voltage cable assemblies with unterminated connections on one end, constructed from PTFE Type C insulated wire. The unterminated connections are coded to match the connector pin designation.
-
Product
PXI/PXIe 1000Base-T1 Fault Insertion Switch, 3-Channel
40-203-001
Fault Insertion Unit
The 40-203-001 (PXI) and 42-203-001 (PXIe) are designed to simulate common faults on high-speed two wire communication interfaces such as 1000Base-T1. They support 3 channels of two wire serial interfaces. Each channel pair can simulate an open fault in either or both wires, and using the fault bus switches can simulate short between both wires or a short to one of two externally applied fault connections – such as battery supply or ground - via two fault buses.
-
Product
Plugbord
4066-4
-
VECTOR Electronics and Technology, Inc.
72 Gold plated edge contacts (36 each side)on 0.100"(2.54mm) centers. Overall ground plane on wiring side. Interleaved zig-zag bus pattern on component side.0.085” diameter etched clearance area around each hole on ground plane sideBus and plane surface solder coated for user convenienceRow and column legends provided
-
Product
Cable Assembly, 78-Pin D-Type, Female to Unterminated With Ferrules
40-972-078-1m-FU
Cable Assembly
A 78-Pin D-Type to Unterminated cable assembly constructed from 7/0.15 (26AWG) Silver Plated Copper Wire. Screwlocks are provided to secure the cable connector to associated products. Has a 45 degree cable exit away from pin 1.
-
Product
Cable Assembly, 160-Pin DIN41612, Female to Unterminated With Tinned Ends, 2m, 45º
A1604F5-T-0A200
Cable Assembly
For applications where a 45 degree cable exit would be preferred with unterminated connections at the other end. The cable assembly is constructed from highly flexible 7/0.15 (26AWG) Silver Plated Copper Wire. If the user requires the connector to have a second fixing then the right hand connector can be fitted with the optional screwlock assembly 40-969-101.
-
Product
Wafer Demounting And Cleaning Machines
-
Demounting and cleaning to high throughput fully automatic ingot after cutting in the slicing machine and wire saw.
-
Product
DC Resistance Tester
DCSS502BC
-
Resistance meter is designed to measure copper resistance of transformers, wires, cables, other conductors and other coil products etc. It is widely used of low resistance measurement of switches, heater wires, transformers, relays, motors, electric films and PC circuit boards, wires, cables, etc. With reliable Good/ NG judgement, it is a premier resistance meter for the use in production line or QC department.
-
Product
Cable 96-Pin Micro-D Female to Female, 2m
40-970B-096-2m-FF
Cable Assembly
The 96-Pin SCSI Style Micro-D Cable Assembly is constructed from 7/36 (28AWG) Tinned Copper twisted pair wiring with Polyolefin insulation to minimise crosstalk. Metal Spring Latches are provided to secure the connectors to their associated products.
-
Product
Cable 96-Pin Micro-D Female to Unterminated, Ferrules, 1m
A096SFR-F-5A100
Cable Assembly
The 96-Pin SCSI Style Micro-D to Unterminated Cable Assy is constructed from 28 AWG Twisted Pair Tinned Copper wire with Polyolefin insulation. Crosstalk is minimised. Wires are colour coded for easy connection. Metal Spring Latches are provided on the 96-Pin connector.
-
Product
Cable Assembly, 9-Pin D-Type Male To Unterminated With Ferrules, 0.5m, HV
40-972-009-0.5m-MU-HV
Cable Assembly
A range of 9-Pin D-Type High Voltage cable assemblies with unterminated connections on one end, constructed from PTFE Type C insulated wire. The unterminated connections are coded to match the connector pin designation and include crimped on ferrules to ensure the wire strands cannot break when they are terminated.
-
Product
Wire Crimp Testers
-
Imada offers manual and motorized wire crimp test systems in either vertical or horizontal configurations.Lever-operated systems offer basic functionality and rapid destructive testing up to 220 lbf.Motorized systems have speed control and are capable of destructive or force-controlled non-destructive testing up to 1100 lbf.Choose from manual or automatic wire-gripping fixtures.Digital gauges offer data output for analysis with data acquisition software.Create your own custom configuration or consult our application specialists.
-
Product
12-600V AC Adjustable Non-Contact Wire Tracer
5221
-
Peaceful Thriving Enterprise Co Ltd
This non-contact voltage tester, can be used to test the presence of AC voltage from 12V~600V, no need of metallic conduction, easy to read by visual and audio indication. Locates breaks along live, insulated wires and power cords. Adjustable sensitivity allows tracing of wires behind walls, around switches or receptacle.
-
Product
Cable Assembly 15-Pin D-Type, Male to Unterminated With Ferrules, 2m
40-972-015-2m-MU
Cable Assembly
The 15-Pin Connector to Unterminated Cable Assy is constructed from PFA insulated 19/0.18 (21AWG) Tinned Copper Wire. The connector can be secured to the associated product by screwlocks.The unterminated connections are coded to match the connector pin designation and include crimped on ferrules to ensure the wire strands cannot break when they are terminated. When using this product additional cable strain relief arrangements may be necessary and appropriate electrical safety precautions should be observed.
-
Product
Cable, 96-Pin 1.27mm Pitch Female To Unterminated, Ferrules, Screwlocks, 2m
A096SFR-F-6A200
-
The 96-Pin 1.27mm Pitch to Unterminated Cable Assy is constructed from 28 AWG Twisted Pair Tinned Copper wire with Polyolefin insulation. Crosstalk is minimised. Wires are colour coded for easy connection. M2.5 screwlocks are provided on the 96-Pin connector.
-
Product
U Type Glow Wire Loop
IEC60695-2-10
-
Shenzhen Chuangxin Instruments Co., Ltd.
Thermo resistance, spare part set of Glow Wire Apparatus Acc IEC60695-2-10. Thermo resistance loop is a wire loop that is defined at a temperature and is pressed against a standardized test platelet made of plastic (or other materials) for a prescribed period of time under precise test conditions.
-
Product
Multi Function Testers
-
Kyoritsu Electrical Instruments Works, Ltd.
Live circuit warning LED:Immediate illumination of a warning lamp if the circuit under test is live Auto Discharge:Allows fast and safe discharge of electrical energy stored in capacitive circuits following testing Integral overload protection on internal continuity and insulation test circuitry Autoranging 500V DC test voltage for insulation tests 200mA short circuit current on continuity ranges Loop and RCD Testing Wiring connection check LED''s:Immediate indication if wiring of circuit under test is correct Overheat Protection:Rapid detection of overheating of internal circuitry,display of warning signal to user and automatic halting of measurement Supply Voltage Indication:Can display supply voltage value in loop impedance mode Low Current Loop Impedance Test:Short duration low test current will prevent tripping of many passive RCDs
-
Product
PXI Pull-Thru Adapter, Wired, QuadraPaddle, to 78 Pin Female D-Sub
510140194
Pull-Thru Adapter
PXI Pull-Thru Adapter, Wired, QuadraPaddle, to 78 Pin Female D-Sub
-
Product
Cable Assembly 68-Pin Micro-D Female to Unterminated, Cut Ends, 0.5m, Spring Latch
40-972-068-0.5m-FU
Cable Assembly
The 68-Pin Connector to Unterminated Cable Assy is constructed from 7/36 (28AWG) twisted pair wires with polypropylene insulation. The wires are colour coded to match the connector pin designation. The connector can be secured to the product by a Metal Spring Latch.
-
Product
20-Pin GMCT Male Connector, 16A, Without Backshell
92-960-020-16A-M
-
This accessory is designed to allow users to directly terminate a cable with soldered connections to the connector. It is supplied with removable solder bucket contacts suitable for wires up to 14 AWG. When the product is used without a backshell users should make their own cable strain relief arrangements and ensure appropriate electrical safety precautions are observed.
-
Product
Two Way Monitoring and Control
-
The Drexelbrook 560 DRX Series wireless products feature 900KHz frequency hopping, spread spectrum technology to provide a reliable, license free, wireless link between the field instrument and the control room.These wireless interface products provide a cost effective alternative to expensive hard wired connections.Using Frequency Hopping Spread Spectrum (FHSS) technology, a robust signal is provided that is virtually free from disruption due to interference.
-
Product
Cable Assembly 15-Pin D-Type, Female to Unterminated With Cut Ends, 1m
A015DF4-C-0A100
Cable Assembly
The 15-Pin Connector to Unterminated Cable Assy is constructed from PFA insulated 19/0.18 (21AWG) Tinned Copper Wire. The connector can be secured to the associated product by screwlocks. The unterminated connections are coded to match the connector pin designation. When using this product additional cable strain relief arrangements may be necessary and appropriate electrical safety precautions should be observed.
-
Product
QAM Compass
-
ingress detection and mitigationhome certification & installation integrityqualify and QC cable drop and installation wiringtroubleshoot and fix repeat service call problemsqualify new cabinet builds and MDU enclosure wiringbuilt-in multi-frequency antenna provides ease-of-usecontractor work verification evaluate new property wiring
-
Product
PXI Switch - 24-CH 2-Wire Multiplexer Module
PXI-7921
Matrix Switch Module
ADLINK PXI-7921 is a relay multiplexer which consists of 24 2-wire relays (DPDT, 2 Form C). As a multiplexer, the PXI-7921 provides 48x1 1-wire, 24x1 2-wire and 12x1 4-wire configurations. Users could choose one of the configurations by software. PXI-7921 typically connects one instrument, such as a DMM, a digitizer or a signal source, with many points which need measurement or excitation. The contact position of the relays can be changed either by direct software commands or by following the instructions previously stored in the on-board scan list. The scan list advances upon the trigger from external measurement devices, such as a DMM. The scan list could also advance when the scan-delay timer expires. In the PXI-7921, PXI trigger functions are supported and software programmable. Multiple modules can therefore be synchronized without additional field wiring.
-
Product
NIM and CAMAC Power Supplies
-
NIM and CAMAC crates require very clean and stable DC supplies with the standard voltages +24V / -24V, +12V / -12V and +6V / -6V. Consequently CERN defined compatible power supplies for both standards within their NIM and CAMAC specs., i.e. CERN spec. power supplies can be used on both types of crates. All "CE" version power supplies are outfitted wth separate AC wiring to comply with CE/UL safety standards.
-
Product
Serial-to-Ethernet Converter
MultiNet
-
MultiNet is a communications module that provides GE Multilin serial ModBus IEDs with ModBus TCP/IP communications over Ethernet, allowing connection to fiber optic LAN and WAN network systems. MultiNet has the capability to connect up to 32 serial ModBus devices eliminating complex wiring and additional communications converters, and providing a streamlined and economical Ethernet hub.
-
Product
AstroAI Multimeter
2000
-
AstroAI Multimeter 2000 Counts Digital Multimeter with DC AC Voltmeter and Ohm Volt Amp Tester ; Measures Voltage, Current, Resistance; Tests Live Wire, Continuity
-
Product
Digital Input/Output Expander (Open-Collector Outputs)
ENVIROMUX-DI16DO16
-
Adds 16 digital inputs and 16 digital open-collector outputs to the ENVIROMUX-2D/5D/16D. Interfaces with the ENVIROMUX-2D/5D/16D via the RJ45 Sensor Port. Digital inputs: 16 screw terminal pairs for connecting dry contact devices; One screw terminal pair for tachometer; 0 to 255 Hz. Accepts 26 to 16AWG wire. Potential free. Voltage range: 0 to +36VDC. Over-voltage surge protected. Digital outputs: 16 screw terminal pairs for open-collector outputs. Accepts 26 to 16AWG wire. Rated sink current: 500 mA per output. +5VDC, 22kΩ pull-ups. Voltage range: 0 to +24VDC. Over-voltage surge protected. Supports CAT5/5e/6 cable up to 500 ft. (152.4 m). Powered by ENVIROMUX-2D/5D/16D. Compatible with ENVIROMUX-2D/5D/16D. Dimensions WxDxH: 6.49x3.10x1.08 in (165x79x27 mm). Regulatory approvals: RoHS.
-
Product
Fixed Gas Detectors
OLCT 10 - OLC 10
-
Teledyne Gas & Flame Detection
The OLC 10 and OLCT 10 are designed to detect combustible or toxic gases for tertiary applications (boiler plants, battery charging rooms, car parks, hospitals). Two OLC 10's can be connected to one detection channel to monitor the same area, without an additional junction box or extra wiring. Similarly, up to five OLCT 10's can be connected to one channel for the detection of CO, NO or NO₂ in a car park application. Easy to install and operate, these detectors combined with the MX 16 control unit meet demanding user requirements.
