-
Product
RF Amplifier
SA1022
-
Hangzhou Softel Optic Co., Ltd.
*1000MHz Broadband RF signal amplifier, Line extender, RF amplifier GaAs MMIC used on the forward path, Power-Double module amplify module are used as output stage, Output level is stable and nonlinear index is good, import high index amplify module are used on return path, its distortion is little and SNR is high.*It is more convenient to debug because of plug-in (or adjustable) duplex filters, plug -in fixed (or adjustable) equalizers, plug-in output splitters and scientific and rational on-line detection ports.*The equipment can work steadily outdoor under bad environmental condition because of waterproof aluminum case, high reliability switching power supply and lightning protection system.
-
Product
Variable Gain Optical Amplifier Module
VGA4500-FM06
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai VGA4500-FM06 series is a next generation variable gain optical amplifier module, which with the most excellent performance and most completes functions in the market. It adopts nowadays most excellent optical performance, most advanced electronic technology and most complete software functions. Remarkable transient suppression control technology and heat management control technology let many complicated optical functions achieved. It is the most versatile multifunction optical amplifier in the market.
-
Product
C-Band Single Channel Line Amplifier EDFA (SLA)
HSA4200 (With SNMP)
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai HSA4200 series is a line EDFA designed specifically for single wavelength optic transmission system. It is installed in the middle of the transmission line, replacing the traditional relay station, to compensate the optical power loss in the line and extend the signal transmission distance.
-
Product
Low Power Op Amplifiers (< 1mA/amp)
-
Analog Devices low power op amps offer a variety of benefits in many applications such as prolonging battery life, easing waste heat management in end equipment, reducing self heating to minimize thermally induced offset shift, and reducing total system power consumption and cost. Offering power efficient devices without compromising speed, noise, and precision has been a key focus on developing products at ADI.
-
Product
Power Amplifiers
-
Triad’s line of RF and microwave Power Amplifier modules for extended range amplified radio applications set the bar for efficiency, linearity, and size-to-power ratio. We have designed hundreds of COTS modules for exacting frequencies up to 40 GHz . They offer high power levels into the hundreds of watts. And if a standard RF/microwave amplifier design does not fit your exact requirements, we’re specialists in creating custom-modified versions of any of our COTS power amplifier modules.
-
Product
GHZ-Wideband Amplifiers
-
Ultra-wide bandwidth from 10 kHz up to 2.5 GHzGain up to 60 dB (x 1,000)Transimpedance gain with photodetectors up to 50,000 V/AVery low input noise down to 310 pV/√Hz (6.2 pA/√Hz)Integrated DC-current path for biased photodetector applicationsTwo identical signal outputs (HSA-Y series)DC-monitor output (HSA-Y series)
-
Product
High Voltage, High Current Linear Amplifier
P200
-
The P200 is a general purpose linear amplifier having a fixed amplification of 10 times and capable of bipolar high voltage output of ±100V. Any functiongenerator or arbitrary waveform generatoror any othe signal source with amplitude up to ±10 V can be used as an input device.
-
Product
Basic Quad J-Type Analog Thermocouple Amplifier
SEN-30103-J0
-
Analog thermocouple amplifier board based on the AD849x from Analog Devices (successor of the AD597). This quad-channel thermocouple board converts the very low voltage signal from a thermocouple to a highly-linear, 0.005V/C output with either 0V or 1.245V offset (both configurations stocked) while removing unwanted noise from the signal. Many supply and output configurations are available with this board, though the PCB was designed with Arduino in mind. Specifically, the output header will plug directly into a standard Arduino Uno or Mega, with a pin-for-pin match for power supply, ground and analog outputs. With a 5V Arduino, temperatures from 0C to 1,000C are possible with the 0V offset board and -249C to 750C with the 1.245V offset board. If using a 3.3V microcontroller (Due, etc), the board must be supplied with no more than 3.3V to avoid damaging the microcontroller. Temperature measurement range is dependent on the supply voltage. It is possible to supply the board with higher voltages to allow temperature measurement over the entire operating range of the K-Type and J-Type thermocouples, allowing use with more capable data acquisition equipment.
-
Product
Solid State Power Amplifiers (SSPAs)
-
CHANGSHA KAIYUAN INSTRUMENTS CO., LTD.
* Ruggedized for use in pulsed airborne, naval and ground radar* Found in weather forecasting Doppler radar systems* Utilized world-wide in air traffic control and precision approach radar systems
-
Product
FTTx PON Optical Amplifier (1540~1563nm)
HA5800C (3RU)
-
Hangzhou Huatai Optic Tech. Co., Ltd.
HA5800C (3RU) series is a low noise, high performance, FTTP high power, multi-ports optical amplifier with gain spectrum band within 1540~1563nm. Each output port for optical amplifier has built-in well-performed CWDM. Every external up-link optical port of optical amplifier can connect with OLT PON port very conveniently. Each 1550nm (CATV)'s output optical port multiplex 1310/1490n's data stream, in order to reduce the quantity of the component and improve the index and reliability of the system.
-
Product
1.5µm PM Fiber Amplifier ( PM EDFA )
HAPM4000
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai HAPM4000 is a Polarization Maintaining Optical Amplifier which working in 1528~1563nm operating wavelength. Adopt Polarization Maintaining Erbium-doped fiber (PM-EDF), output optical power range 13~26dBm, extinction ratio >20dB.
-
Product
GaN Power Amplifiers > 5W
-
Macom Technology Solutions Holdings Inc.
MACOM GaN RF power amplifier solutions are designed with the latest GaN-on-SiC and GaN-on-Si technologies. Our MACOM PURE CARBIDE series of GaN-on-SiC power amplifiers offers high performance and reliability for the most demanding applications. Our expanding GaN portfolio is designed to address the challenging requirements of Aerospace & Defense, Industrial, Scientific and Medical applications and 5G wireless infrastructure. MACOM GaN products deliver output power levels ranging from 2 W to over 7 kW and exhibit best in class RF performance with respect to gain and efficiency. For sensitive Aerospace & Defense applications MACOM can offer a US only supply chain with AS9100D Certification.
-
Product
Panel-mounted Power Amplifier(Hardware In The Loop Simulation)
PA30Bi
-
PA30Bi is the panel-mounted type real time simulation amplifier with three-phase current and four-phase voltage.
-
Product
Synchronization and Distribution Amplifier - PCIe
Model 7892
-
The Model 7892 High-Speed Synchronizer and Distribution PCIe Board synchronizes multiple Pentek Cobalt or Onyx boards within a system. It enables synchronous sampling and timing for a wide range of multichannel high-speed data acquisition, DSP, and software radio applications
-
Product
Amplifier Gain Blocks
-
Macom Technology Solutions Holdings Inc.
At MACOM we design, manufacture, and support a wide portfolio of Amplifier Gain Blocks for RF, microwave, and millimeter wave applications. Our amplifier gain blocks cover frequencies ranging from DC to 45 GHz. MACOM’s gain blocks are used in a variety of 50 Ohm and 75 Ohm applications including; Networks, Commercial and Aerospace and Defense. Leveraging the latest innovative technology these products are available in both standard plastic packaging and bare die.
-
Product
Super Low Noise Amplifiers
WCA Series
-
WCA series super low noise amplifiers have sub-0.5 dB noise figure at VHF band with several octave bandwidth. The amplifiers have 75 Ohm impedance.
-
Product
Distribution Amplifiers
-
A complete range of distribution amplifiers are manufactured by Precision Test Systems. A distribution amplifier is used to distribute the output of a frequency reference to many different places. Usually the frequency is 5 or 10 MHz but we manufacture distribution amps from DC to over 2000 MHz. We make some of the industries lowest phase noise products.
-
-
Product
SSPAs / LNAs / Broadband
-
SSPAs based on the latest Galium Nitride (GaN) technology offer the best combination of high peak powers, high reliability, high efficiency, and soft degradation. High efficiency and high power are hallmarks of GaN technology, enabling SSPAs to challenge traditional tube-based amplifiers across the design spectrum. In addition the long lifetime from these devices, combined with the gradual degradation should individual devices fail, provide unparalleled service lifetime. Techniques such as bias modulation and linearization provide even better prime-power efficiency while still meeting the demanding requirements of pulsed or CW applications.
-
Product
40mA Multi-Channel Amplifier
-
For the precise nanometer movement of actuators and other piezo products, an amplifier is required. Multi-channel amplifiers allow you to control multiple actuators or piezo products with a single amplifier. The NV40/3 piezo amplifier was designed for controlling low voltage piezo elements. It includes a voltage amplifier, a display and a PC-interface. The high-resolution display shows the voltage of the actuator, along with the mode of operation and the temperature inside the amplifier.
-
Product
Low Frequency RF Broadband Power Sources
-
Class A has RF power source, ideal for Industrial /Scientific / Medical applications. Class AS is a robust source of RF power for ultrasonic, laser modulation, RFI/EMI, plasma generation, general laboratory and industrial applications.
-
Product
C-Band Separate Raman Fiber Amplifier
RFA5000
-
Hangzhou Huatai Optic Tech. Co., Ltd.
1. Erbium-doped Fiber Amplifier, due to the multiple cascades and the accumulation of noise caused by spontaneous emission, will reduce the system CNR greatly and thus it will limit the transmission capacity and distance of the system. Raman Fiber Amplifier (RFA) is a newly designed fiber amplifier based on Stimulated Raman Scattering (SRS) effect. It is considered as the core technology of new generation DWDM fiber over-long communication. Compared with Erbium-Doped Fiber Amplifier, Raman amplifier has the advantage of low Noise Figure (NF), wider gain bandwidth, flexible gain spectral region and stable temperature. It is the only device that can operate in 1300~1600 nm.
-
Product
Low Phase Noise Amplifiers
-
Low Phase Noise amplifiers are critical for many applications requiring high signal integrity. This is especially relevant in instrumentation, defense, and telecommunication applications where low phase noise amplifiers are becoming increasingly important as the oscillators improve. Phase noise is described as the close-in noise to the carrier that can often appear as jitter on a clock signal. Analog Devices offers a large portfolio of low phase noise amplifiers to meet a variety of requirements in the LO network, receiver, as well as in the transmitter. Our portfolio supports a wide range of power levels and frequencies to provide the right solution for the given application.
-
Product
Composite 1×24 Video Distribution Amplifier
VDA124RM
-
Video Distribution Amplifiers (sometimes called a video splitter – not to be confused with a video split screen controller such as our PXD510E split screen controller) are typically used for connecting a camera or other video source to several monitors that do not have “looping” inputs. In this situation, each monitor has a permanent 75 ohm termination. With two non-looping monitors connected together, the line would be double loaded and result in a dim picture on each monitor. Using a Video Distribution Amplifier will solve this problem by driving each monitor individually at 100%.
-
Product
Amplifier Module
LNAM-LPA
-
We offer an evaluation board and case for the LNAM-B and LNAM-FBX modules. This Laboratory PreAmplifier (LPA) solution is powered by a switch-mode power supply and gives access to the LNAM in- and outputs via BNC sockets.
-
Product
Low Noise Amplifiers
-
Electronic component that amplifies a very low-power signal without significantly degrading its signal-to-noise ratio (SNR).
-
Product
Low Noise Amplifiers
-
Our range of ITAR Free, Low Noise Amplifiers (LNAs) cover a variety of applications but are primarily suited to airborne, maritime and ground based radar systems. LNAs are primarily intended to minimise added noise whilst providing high gain so design focusses on the parameters associated with the noise response of the amplifier. They are usually the first amplifier in the Radar detection chain and will have the lowest noise figure.
-
-
Product
Measurement Power Amplifier
Qam
-
The amplifier is DSP controlled, with a very straightforward operation. Included is a white/pink noise signal generator. The internal signal module provides low crest noise signals to be able to reach high power levels from sound sources or electromagnetic shaker. External input of signal is equally possible, with spectral linearisation or without. This can be used for music, RASTI or any other signal
-
Product
Slim & High-Performance Charge Amplifier
6001-A, 6002-A
-
Measuring a wide variety of vibration: automotive, rail transportation equipment vibration, motor/pump vibration, vibration response during vibration test. Also available for a vibration test device for calibration of equipment.
