OBD 2
-
Product
PXI-4132, 100 V, 2 W Precision PXI Source Measure Unit
780558-01
Source Measure Unit
±100 V, 10 pA Precision PXI Source Measure Unit—The PXI-4132 is a programmable, high-precision source measure unit (SMU). It has a single isolated SMU channel that offers a four-quadrant output that incorporates remote (4-wire) sense as well as external guarding. With its high measurement resolution integrated guarding, the PXI-4132 is ideal for high-accuracy leakage measurements on integrated circuits, discrete components, PCBs, and cables. You can also perform high-speed I-V measurements on a variety of components including diodes and organic LEDs using the onboard hardware sequencing engine. In addition, you can synchronize multiple PXI-4132 modules using the PXI backplane to provide high-speed I-V measurements on transistors and more complex devices.
-
Product
PXI-5154, 1 GHz, 2 GS/s, 8-Bit, 256 MB/ch, PXI Oscilloscope
780319-03
Oscilloscope
1 GHz, 2 GS/s, 8-Bit, 256 MB/ch, PXI Oscilloscope—The PXI‑5154 is ideal for acquisition and characterization of fast, nanosecond-edge speeds. It is well-suited for automated test and data streaming applications in the consumer electronics, semiconductor, aerospace/defense, and life sciences industries. The PXI‑5154 also comes equipped with up to 256 MB of memory per channel to provide high, sustained sample rates over extended data capture windows. This digitizer, optimized for automated test, uses a high-throughput bus to lower test times, provides picosecond-level synchronization among modules, and integrates with the entire suite of NI hardware, so you can build and customize a complete mixed-signal or high‑channel‑count test system.
-
Product
Oscilloscope, 200 MHz, 2 GS/s interleaved, 4 CH, 200 Mpts/Ch interleaved, Fully Loaded DSO with 16 Dig Ch MSO
T3DSO2204HD-MS
Oscilloscope
The T3DSO2000HD series of Bench Oscilloscopes feature 4-channel models with analog bandwidth options of 100 MHz, 200MHz and 350 MHz. The T3DSO2000HD Oscilloscopes use 12-bit high resolution ADCs and a low noise front end which provides an impressive noise performance to cover a wide range of measurement applications. Each model offers a maximum sample rate of 2 GSa/s (interleaved) and a maximum memory depth of 200 Mpts in interleave mode. The MS configured models also include a 16 channel logic probe as standard.
-
Product
PXI Switched Guard Reed Relay Module, 16x 2:1 Multiplexer
40-121-011
Multiplexer Module
The 40-121-011 provides 16x 2:1 multiplexers in a single slot PXI module and designed to provide an isolation resistance in excess of 1013Ω. It has been designed to ensure high isolation resistance through the use of switched guards, making it ideal for low level measurements and semiconductor test.
-
Product
Cable & Antenna Analyzer - 2 MHz to 4.4 GHz
E7000L
-
The E7000L Cable & Antenna Analyzer provides all necessary measurement functions and performance to accurately diagnose and verify the site’s cable and antenna system and RF connectors, as well as basic fiber-feedline testing. Smaller and lighter than the E7000B, the E7000L is ideal for installation of wireless cell sites.
-
Product
500-Pin SEARAY Cable Assembly, Male to Male, 2 Amp, 0.5m, 250 Port
A500RMR-500RMR-4B050
Cable Assembly
The 500-Pin SEARAY connector is used on switching products to provide a very high density 2A connector solution that is suitable for use to 200VDC. This cable assembly is suitable for direct connection to Pickering Interfaces products using the 500-Pin SEARAY connector. Screwlocks are provided to secure the cable assembly to a mating product.
-
Product
BNC Male to BNC Male Cable, 75 Ohm, 2 m (Quantity 4)
779697-02
Coaxial Cable
The BNC-BNC Coaxial Cable, sometimes referred to as BNC Plug to BNC Plug, connects measurement and signal devices.
-
Product
Mini-ITX SBC With LGA1151 9th/8th Gen Intel® Core™ I7/i5/i3 Processor, Dual DisplayPort++, HDMI, LVDS, USB 3.0, MSATA, M.2 And Dual GbE LAN
MANO520
-
The MANO520 is powered by the LGA1151 socket 9th/8th generation Intel® Core™ i7/i5/i3 (code name: Coffee Lake), Intel® Pentium® Gold or Intel® Celeron® processor with the Intel® Q310 chipset (Intel® Q370 optional). The Intel® Coffee Lake-based MANO520 is specifically designed for performance-demanding applications with its excellent reliability as well as communication and real-time computing capabilities. The MANO520 supports two 260-pin DDR4-2666/2400 SO-DIMM sockets for up to 32GB of memory. Also, the mini-ITX motherboard features three SATA-600 connectors and one mSATA for additional storage. It is equipped with one full-size PCI Express Mini Card, one PCIe x16 and one M.2 Key E slots for wireless devices such as Wi-Fi, Bluetooth, and 3G/LTE. Moreover, the mini-ITX form factor single board computer features an ATX connector with AT mode auto power function.
-
Product
PCI 2 Amp Multiplexer, Dual 8-Channel, 2-Pole
50-635A-106
Multiplexer Module
The 50-635A-106 is a dual 8-channel, 2-pole MUX and is part of a range of PCI Multiplexer cards available in 9 standard density and 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
Product
Dual 2 Channel Fibre Optic Mux SC/PC
40-815-222
Fiber Optic Switch
Pickering PXI Fiber Optic Multiplexers connect a single channel to one of two or four channels. They are available in single or dual multiplexer configurations supporting single-mode or multi-mode fiber. A wide choice of connectors types is available. The 40-810 multiplexer connects the optical channel by redirecting the optical signal into a selected output fiber.
-
Product
MSN Sniffer 2
-
MSN Sniffer is world's first sniffer to automate MSN chat capturing and impact analysis. After installed on one computer, it captures MSN chat across all computers in the same LAN, analyze and save into database for future analysis.
-
Product
PXI 2 Amp MUX, Single 32-Channel 1-Pole
40-635-101
Multiplexer Module
The 40-635 2 Amp Multiplexer module is available in 9 standard configurations as well as 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.The module is suitable for signal routing in ATE and data acquisition systems. Connections are made via a front panel 78-way D-type connector.
-
Product
PCI Programmable Resistor Card 4-Channel 2 Ohm To 510 Ohm - SPST
50-294-114
Programmable Resistor Module
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
2 GHz to 6 GHz, 25 W Power Amplifier Module
HMC7748
-
The HMC7748 is a multistage power amplifier (PA) that provides 25 W of saturated output power across the band of 2 GHz to 6 GHz. It draws 0.7 A from a 12 V supply and up to 4 A from a 28 V supply. Input signals of as much as −8 dBm are acceptable, and the module has small signal gain of 60 dB. The 12 V supply is regulated internally and generates the negative voltage required for the gate bias. Built-in bias sequencing prevents the drain voltages for the amplifier stages from being applied without the negative voltage present, which protects the amplifiers if 28 V is applied without 12 V supply applied.
-
Product
Infiniium UXR-Series Oscilloscope: 59 GHz, 2 Channels
UXR0592A
Oscilloscope
The UXR0592A is the 59 GHz, 2 channel, Infiniium UXR-Series real-time oscilloscope
-
Product
SWB-2834, 8x34, 2 A, Electromechanical Relay Matrix Module for SwitchBlock
781421-34
Relay Matrix Module
8x34, 2 A, Electromechanical Relay Matrix Module for SwitchBlock - The SWB‑2834 is an electromechanical relay matrix card for SwitchBlock systems. Designed for high power, it can operate as an individual relay card or expand in a single carrier or single PXI chassis. You can connect any input to any output, individually or in combination. You can use matrix switches to route signals from oscilloscopes, DMMs, arbitrary waveform generators, and power supplies to various test points on a unit under test (UUT). The primary benefit of matrix switches is simplified wiring—the overall test system can easily and dynamically change the internal connection path without any external manual intervention.
-
Product
PXI 2-Slot BRIC Matrix, 22x16 1-Pole (2 Sub-cards)
40-562B-221-22X16
Matrix Switch Module
The 40-562B-221-22X16 is a high density BRIC2 matrix module with a size of 22x16 with 1-pole switching. It is part of a range of BRIC matrices available in 2, 4, 8 or 12-slot formats to suit high performance PXI matrix requirements and is constructed using instrumentation quality reed relays.
-
Product
AngelShark Carrier Board™ Mac Pro (Late 2013) Cylinder Storage Upgrade by M.2 PCIe SSD
SKU-088-01
-
How to upgrade storage capacity (the SSD) on a Mac Pro (Late 2013) cylinder?It is possible with the AngelShark Carrier board™ (designed & produced by Amfeltec Corporation, Canada).Carrier board is located internally between the Mac and the original SSD module. It supports any M.2 PCI Express (M-key) SSD modules with standard lengths 2280 and 2260, 22110 (optional).Carrier Board supports x4 PCI Express Gen 3 connection on each M.2 circuit, and it is compliant with PCI Express Specification 3.0 and M.2 Specification 1.1.
-
Product
WaveRunner Oscilloscope, 4 GHz Bandwidth, 4 Input Channels, 20 GS/s on 2 Ch Sample Rate
WaveRunner 9404
Oscilloscope
4 GHz, 20 GS/s, 4ch, 16 Mpts/Ch DSO with 15.4" Capacitive Display.
-
Product
PXI 2 Slot BRIC 30x16 2-pole (2 sub-cards)
40-561A-222-30X16
Matrix Switch Module
The 40-561A-222-30x16 is part of a range of high-density PXI BRIC matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays.
-
Product
2 PICMG® CPU, 7 PCI™, 1 ISA Slots Backplane
HPCI-9S7U
Backplane
- Segment: 1- Slots: 2 PICMG® CPU, 7 PCI™, 1 ISA- Supports AT, ATX power supplies- Dimensions: 213.4 mm x 259.1 mm
-
Product
Cable Assembly, Receiver, TriPaddle, 20", 2 20-Pin Female Power Connectors
540054010101
Cable Assembly
Cable Assembly, Receiver, TriPaddle, 20", 2 20-Pin Female Power Connectors
-
Product
PCI 2 Amp Multiplexer, Quad 8-Channel, 2-Pole
50-635A-009
Multiplexer Module
The 50-635A-009 is a quad 8-channel, 2-pole MUX and is part of a range of PCI Multiplexer cards available in 9 standard density and 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
Product
Squid PCI Express Carrier Boards for M.2 SSD Modules
SKU-064-2X
-
Flexible x1 PCI Express to 3 MiniPCI Express Splitter (Splitter) was designed to expand modern motherboard (ATX, mini ATX etc.) that have PCI Express interface. It allows you to connect up to three MiniPCI Express add-in boards to the standard motherboard PCI Express connector.Splitter includes 3 MiniPCI Express adapter boards, x1 PCI Express host board and 3 flat PCI Express Cables.
-
Product
PCIe 8 Bit High Speed Digitizer - 5 GS/s on 1 Channel, 2.5 GS/s on 2 Channels, 1.25 GS/s on 4 Channels, 1.5 GHz Bandwidth
M4I.2234-X8
Digitizer
The 9 models of the M4i.22xx-x8 Express series are designed for the high speed data acquisition. Each of the input channels has its own A/D converter and its own programmable input amplifier. This allows the recording of signals simultaneously on all channels without any phase delay between them. The extremely large on-board memory allows long time recording even with the highest sampling rates.
-
Product
PXI 1 Bank of 80 Channel 2 Pole MUX
40-615-022-1/80/2
Multiplexer Module
High density multiplexer modules featuring a wide range of switching configurations, especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems. Each module is factory configured into one of the configuration modes. Connections are made via a front panel 200-pin connector.
-
Product
PXIe-6396, 8 AI (18-Bit, 14 MS/s/ch), 2 AO, 24 DIO, PXI Multifunction I/O Module
785927-01
Multifunction I/O
PXIe, 8 AI (18-Bit, 14 MS/s/ch), 2 AO, 24 DIO, PXI Multifunction I/O Module - The PXIe-6396 is a simultaneous sampling, multifunction DAQ device. It offers analog I/O, digital I/O, four 32‑bit counters, and analog and digital triggering. Onboard NI-STC3 timing and synchronization technology delivers advanced timing functionality, including independent analog and digital timing engines and retriggerable measurement tasks. The PXIe-6396 is ideal for a variety of applications, such as IF digitization; transient recording; ISDN, ADSL, and POTS manufacturing test in the telecom industry; ultrasound and sonar testing; and high-energy physics. The included NI-DAQmx driver and configuration utility simplify configuration and measurements.
-
Product
CalPod Drive Cable, 40 GHz, 2 Meter
85553A
Calibration Cable
This cable provides the bias voltages and control signals for operation of the 40 GHz CalPod modules. This cable is supplied with the 85540/41/42A CalPod modules.
-
Product
20 Bit / 2 MS/s Arbitrary Waveform Generator
AWG20
Waveform Generator
The AWG20 is a 20 bit Arbitrary Waveform Generator for medium-speed / high resolution waveform generation. The module combines an excellent dynamic performance with a very high DC accuracy.
-
Product
DC/DC Converter 2 W
REM2-3.312D
-
DC/DC converter 2 W from Recom | input ranges 3 - 3.6 VDC | outputs +/-12 V | operates in ambient temperature from -40 to +95 °C
