Filter Results By:
Products
Applications
Manufacturers
-
product
Frequency Synthesiser
RA062-F2
The RA062-F2 is a multiple LO module used to generate three pairs of LO signals, each pair being phase matched in order to provide the capability to drive two phase and amplitude matched, high sensitivity narrowband receivers such as might be required for an EW receiver system with DF functionality.The Stepped Frequency Synthesiser is based upon Direct Frequency Synthesis, DFS, whereby the 1GHz input reference signal is multiplied, filtered and mixed to generate a given number of isolated and filtered single tone CW signals from the 1GHz comb. A finely tuned signal is then generated using a multi-way switch to select between the 1GHz spaced CW tones and mixed with fine resolution signals generated using a custom DDS/VCO PLL network. In this way finely tuned signals can be generated between 7.5GHz and 23GHz.
-
product
User Programmable Logic
PCIe-Spartan-VI
User Programmable logic - Spartan VI 100 with 40 differential and 12 TTL IO plus PLL(24). 16 DMA ports, to support 8 full duplex byte lanes between the Bus and User FPGAs. Additional GPB interface to support R/W operations to registers etc. Driver and reference SW package includes user defined R/W to User FPGA to support User Architecture without a new driver.
-
product
DC - 12 GHz Packaged High Efficiency Divide by 8 Prescaler
HMMC-3128-TR1
The HMMC-3128-TR1 is a packaged DC - 12 GHz divide by eight prescaler designed for use in high frequency communications, microwave instrumentation, and EW radar systems where low phase-noise PLL control circuitry or broadband frequency translation is required.
-
product
Agile Modulator
Sichuan Jiuzhou Electronic Technology Co.,Ltd
* High stability webbing filter.* Spurious suppression ≥60dB.* Fourfold PLL frequency lock.* IF input and IF output are equipped on rear panel.* High quality RF hybrid ensures high output level and low distortion.* LED on front panel displays channel number.* Power-off memory functioned.
-
product
6.8 GHz Wideband Synthesizer with Integrated VCO
ADF4356
The ADF4356 allows implementation of fractional-N or integer-N phase-locked loop (PLL) frequency synthesizers when used with an external loop filter and an external reference frequency. A series of frequency dividers at another frequency output permits operation from 53.125 MHz to 6800 MHz. The ADF4356 has an integrated VCO with a fundamental output frequency ranging from 3400 MHz to 6800 MHz. In addition, the VCO frequency is connected to divide by 1, 2, 4, 8, 16, 32, or 64 circuits that allow the user to generate RF output frequencies as low as 53.125 MHz. For applications that require isolation, the RF output stage can be muted. The mute function is both pin- and software-controllable.
-
product
Fixed Source PLL DRO Replacement
ESP Series 2.25” x 2.25” x 0.6”
*Connectorized Package *Exceptionally-Low Phase Noise *DRO Replacement *Optional Internal Reference *Robust Designs Available *Optionally Hermetically-Sealed
-
product
500 / 1000 / 1500MHz Synthesized Signal Generator
Model 2100 Series
- Combine with DDS and PLL Techniques- 1500MHz Maximum Frequency- 1 ppm High Accuracy, Less Distortion- Dual Independent Outputs- AM, FM, FSK, PSK Modulation
-
product
Multicoupler, Rack Mount, 1U, Switchable Dual 2×4/1×8, P/LL/UL/S , Programmable Amplitude Balance
LS-16-R1-24SPLUS
High Performance rack mount 1U x 12” deep switchable Multicouplers are available in multiple IN X OUT configurations, such as 1×8, dual 2×4, 1×4 and 1×6. The LS-16 product line covers 300 MHz to 6000 MHz. High output/output isolation and Ethernet / USB controllable gain adjustments for each channel are available as options.
-
product
PCI Express PLL Test Application
N1081PLCA
Keysight N1081PLCA PCI Express PLL Test Application designed to measure transmitter PLL bandwidth and peaking based on the PCI Express 5.0 TX PLL Specifications. Use N1081PLCA PCIe PLL test software to test, debug and characterize your PCIe designs.
-
product
Film Capacitors
Panasonic Industrial Devices Sales Company of America
Low ESR. Low Dissipation Factors. No Shock Noise. Panasonic Surface Mount Film Capacitors offer stable capacitance and temperature characteristics, tight tolerances, low ESR, low dissipation factors, no shock noise, no piezoelectric effect and no audible noise. Surface Mount Film Capacitor applications include DC blocking and filtering, PLL, audio, DC/DC converter and back lighting.
-
product
Clock Generation Devices
Analog Devices offers ultralow jitter clock generation products for wireless infrastructure, instrumentation, broadband, automatic test equipment, and other applications demanding subpicosecond performance. Our clock products are ideal for generating the high speed, low noise clock signals required to clock high performance analog-to-digital converters (ADCs) and digital-to-analog converters (DACs). ADI clock ICs integrate PLL cores, dividers, phase offset, skew adjust, and clock drivers in small chip scale packages.
-
product
FMC Module
FMC1831
Sundance Multiprocessor Technology Ltd.
The FMC1831 is an FMC module designed to be compatible with AMC, VPX, PCI, PCIe, CompactPCI and PC/104 carriers. The module has two dual channel AD9361 transceivers with a maximum sampling frequency of 122.8 MHz over a bandwidth of 200 KHz to 56 MHz. A reference clock can be either externally supplied or be generated from an internal PLL. All input and output signals are connected via SSMC connectors for secure connectivity and signal integrity.
-
product
RTAX/RTSX Netlist Converter
RTAX/RTSX EDIF and PDC/PIN Converter combines two functions supporting Aldec RTAX prototyping - it provides EDIFs netlists conversion and PDC/PIN constraints file remapping for two families RTAX-S/SL and RTSX-SU/S, SX-A. RTAX/RTSX EDIF and PDC/PIN Converter performs automatic conversion of the RTAX-S/SL and RTSX-SU/S, SX-A EDIFs netlists to ProASIC3/E EDIF netlist, which means replacement of the PLL and memory primitives has to be done, with consideration of the limitations caused by the differences between RTAX-S/SL, RTSX-SU/S, SX-A and ProASIC3/E technologies.
-
product
DC - 12 GHz High Efficiency GaAs HBT MMIC Divide by 8 Prescaler
HMMC-3028
The HMMC-3028 is a DC - 12 GHz divide by eight prescaler designed for use in high frequency communications, microwave instrumentation, and EW radar systems where low phase-noise PLL control circuitry or broadband frequency translation is required.
-
product
1208/9a Optical Distribution, RX/TX
Precise Time and Frequency, Inc.
The ptf 1208A (transmitter) and ptf 1209A (receiver) provide a convenient and simple way to transmit high quality RF signals over long distances, without the concerns associated with electrical interference and pick-up.The ptf 1208A accepts an RF input in the range from 1kHz up to greater than 10MHz and provides a combination of 8 local, high isolation, RF distribution outputs and 4 optical transmission outputs for distances up to 2 kilometers.The ptf 1209A accepts an optical input (transmitted from the ptf 1208A) and provides 12 local RF outputs, either digital (TTL into 50 ohms) or low noise sine wave signals driving 1V rms into 50 ohms (with the PLL option), or both.These systems are especially designed to accommodate IRIG B DCLS, 1PPS and other RF signals in the range from 1kHz to 20MHz.The modular construction allows for a variety of input/output configurations to provide a fully tailored application solution.
-
product
Signal Analyzer
bsw TestSystems & Consulting AG
The simplest way to measure the phase noise is to compare the Device-Under-Test (DUT) to the source of a spectrum analyzer. With the SA set at the same frequency as the OUT, you see the sum of the SA's and DUT's sideband-power spectrum on the SA display. It is a simple and straight forward method well suited for free running VCO's where the SA is easily an order better.You can improve on this method by establishing a Phase Lock (PLL) between the DUT and the Local Oscillator and create a zero-IF or base-band spectrum analyzer system.
-
product
DC - 12 GHz Packaged High Efficiency Divide by 8 Prescaler
HMMC-3128-BLK
TheHMMC-3128-BLK is a packaged DC - 12 GHz divide by eight prescaler designed for use in high frequency communications, microwave instrumentation, and EW radar systems where low phase-noise PLL control circuitry or broadband frequency translation is required.
-
product
Oscillators
VCXO
A VCXO Voltage-Controlled Crystal Oscillator is a crystal oscillator that''s frequency can be adjusted by an externally applied voltage. VCXO''s have a wide variety of applications in frequency modulation (FM) and phase-locked-loop (PLL) systems. Typical deviation ranges can be 10 ppm to as much as 2000 ppm. The device that allows a crystal oscillator''s frequency to be voltage controlled is known as a varactor diode.
-
product
DC - 12 GHz High Efficiency GaAs HBT MMIC Divide by 2 Prescaler
HMMC-3022
The HMMC-3022 is a DC - 12 GHz divide by two prescaler designed for use in high frequency communications, microwave instrumentation, and EW radar systems where low phase-noise PLL control circuitry or broadband frequency translation is required.
-
product
High-Performance USB-Controlled PLL Synthesizers
Rugged, SMA-connectorized designs that support a USB 2.0 interface with a PC supplying DC power and GUI command control. They cover a broad range of frequency bands from 25 MHz to 27 GHz. These USB-Controlled PLL Synthesizers deliver output attenuation that is adjustable up to 50 dB in 1 dB steps and high output power levels ranging from +10 dBm to +19 dBm typical. Phase noise is as low as -108 dBc/Hz at 100 MHz offset and phase locked speed is 1 msec typical.
-
product
VXI Precision PLL Waveform Synthesizer
3152B
The Racal Instruments™ 3152B Waveform Synthesizer combines 250 MS/s waveform generation performance, versatility, and compact size into a single-slot VXIbus format.The 3152B is a greatly improved version of a fi eld-proven instrument ideal for VXI test stimulus generation. It replaces the 3152A which is standard on many military and commercial test platforms
-
product
Continuous Time Interval Analyzers
GT668PXIe-40
GuideTech’s GT668PXIe-40 PXI 3U form factor, meets industrial standard chassis with an expandable platform, achieving optimal test system at low cost. High accuracy 50MHz time base with NIST traceable calibration. Some of the GT668PXIe-40 measurements include Jitter measurements, PLL & Clock Jitter, Spread Spectrum Modulation, PLL Lock Time, Frequency, Period, Pulse Width, Skew, Tpd, Rise/Fall Time, Time Interval Error and more.
-
product
VXI Single/Dual Channel Arbitrary Waveform Generator
3100M
The Astronics Test Systems 3100M Waveform Synthesizer Series combines 300 MS/s waveform generation performance, versatility, and compact size into a single-slot VXIbus format.The 3100M is a greatly improved version of a field-proven instrument ideal for VXI test stimulus generation. It replaces one or two of the popular 3152A Precision PLL Waveform Synthesizers, which are standard on many military and commercial test platforms.
-
product
Fractional-N PLLs
Analog Devices’ leading PLL synthesizer family includes single and dual PLLs, as well as fractional-N and integer-N, and highly integrated PLLs with VCOs. They feature best-in-class performance, phase noise, and integration.
-
product
Phase Locked Loop with Integrated VCO
PLL with integrated VCOs provide local oscillator sources and clock sources for communications (COMMS) , test and measurement (ETM) and aerospace/defense (ADEF) applications. ADI's PLLs with integrated VCO portfolio includes both narrowband and wideband parts, supporting frequencies up to 13.6GHz. Our PLLs with integrated VCO, as well as our full PLL portfolio including integer-N and fractional-N PLLs, feature best-in-class performance for phase noise, jitter, and spurious, and also feature high levels of integration in small form factor packages.
-
product
nanoSynth® Integrated 6 GHz SMT Synthesizer
Nano Series
The SC800 nanoSynth® is a fully integrated broadband CW signal synthesizer that combines multiple PLL, DDS, and frequency dividers into a rugged and miniature 2”x1” surface mountable package. The output frequency range is 25 MHz to 6 GHz with average output power of +10 dBm. Tuning at 1 Hz resolution, the multiple PLL architecture eliminates close-in phase spurs that are associated with fractional-N PLLs. To simplify user communication with the device, an onboard microprocessor performs all necessary computations to control and set the output frequency, reducing the number and complexity of instruction registers.
-
product
Vector Spectrum Analyzer
VSA6G2A
Frequency Range: Low Band: low band 100Hz~2MHz, high Band 1MHz~6.2GHz. Frequency Spans: 100Hz~1.35MHz at FFT mode, 1.35MHz~6188MHz at PLL mode full span sweep time 820ms. Sweep Time: PLL mode: 262ms to 200s, FFT mode: 3.33ms~40s. Aplications: FM radio, Two way radio, TV application, Remote controller; Cellular and PCS, CDMA and GSM, GPRS, Edge,WCDMA and 3G, LTE, 915MHz, 2.4G ISM band application, 5.8G ISM band application.
-
product
Microwave Wideband Synthesizer w/ Integrated VCO
ADF4371
The ADF4371 allows implementation of fractional-N or interger-N phase-loacked loop (PLL) frequency synthesizers when used with an external loop filter and an external reference frequency. The wideband microwave VCO design allows frequencies from 62.5 MHz to 32 GHz to be integrated
-
product
Bit-Pattern Generator Family
PXI(e)520x
6.6 MS/s with 8 Bit pattern widthUp to 2 independent modules with 4 simultaneously working channelsBased on VX Instruments FlexCPP for easy custom designMultiple instrument and channel synchronization possibilitiesAdditional reference clock outputWide range of sample rates due to programmable internal PLL
-
product
Microwave Wideband Synthesizer w/ Integrated VCO
ADF5356
The ADF5356 allows implementation of fractional-N or integer-N phase-locked loop (PLL) frequency synthesizers when used with an external loop filter and an external reference frequency. The wideband microwave VCO design permits frequency operation from 6.8 GHz to 13.6 GHz at one radio frequency (RF) output. A series of frequency dividers at another frequency output permits operation from 53.125 MHz to 6800 MHz. The ADF5356 has an integrated VCO with a fundamental output frequency ranging from 3400 MHz to 6800 MHz. In addition, the VCO frequency is connected to divide by 1, 2, 4, 8, 16, 32, or 64 circuits that allow the user to generate RF output frequencies as low as 53.125 MHz. For applications that require isolation, the RF output stage can be muted. The mute function is both pin- and software-controllable.
