Serial I/O
Sequential input and output of data.
-
Product
6-Pwer Relay/6DI IoT Modbus/SNMP/MQTT Ethernet Remote I/O
ADAM-6066
-
I/O:6ch relay/6ch digital input(counter)Protocols:MQTT(TLS),SNMP,Modbus TCP,RESTful API,ASCIIGCL to perform basic logic control rulesPeer-to-Peer function to map I/O statusCloud access: Data update to AzureBuilt-in web serverWatchdog timer to recover the system
-
Product
96-Ch Digital I/O PCI Card
PCI-1753
-
Emulates mode 0 of 8255 PPIBuffered circuits for higher driving capacity than 8255Multiple-source interrupt handlingInterrupt output pin for simultaneously triggering external devices with the interruptOutput status read-back“Pattern match” and “Change of state” interrupt functions for critical I/O monitoringKeeps I/O setting and digital output values when hot system resetSupports dry contact and wet contactHigh-density 100-pin SCSI connector
-
Product
PXI-6513, 64-Channel, ±30 VDC, Sink Outputs, Bank-Isolated PXI Digital I/O Module
778971-01
-
64-Channel, ±30 VDC, Sink Outputs, Bank-Isolated PXI Digital I/O Module—The PXI‑6513 is an industrial digital output interface with eight banks of isolated channels. With programmable power-up states, you can configure the initial output states in software to ensure safe operation when connected to industrial actuators. If a computer or application fault occurs, the PXI‑6513 can use digital I/O watchdogs to switch to a configurable safe output state to ensure detection and safe recovery from fault conditions.
-
Product
3U CompactPCI® RS-232/422/485 Serial Communication Card
MIC-3955
-
The MIC-3955 is a low power 4-port or 8-port RS232/RS422/RS485 serial board with 3U CPCI form factor and is based on the EXAR PCI controller. MIC-3955 is PICMG 2.0 Rev. 3.0 compatible. Rear board module are named MIC-3527XX. The MIC-3955 supports front IO or rear IO with 4-port and 8-port, and every channel is independent.
-
Product
Ethernet / Serial Device Servers
-
Advantech serial device servers and gateways convert legacy protocols and interfaces to networks, satisfying your industrial communication needs.
-
Product
Embedded Controllers And Super I/O
-
Our portfolio of embedded and industrial controllers supports the unique requirements and long life cycles of embedded computing applications. In each category of products, you will find an array of devices that offer a variety of features including varying numbers of fan tachometers, PECI support, General-Purpose I/O (GPIO) pins and support for different interfaces and other options to meet your specific needs. They are also backed by our client-driven obsolescence practice of continuing to supply a product for as long as possible and while demand for the product exists, which means that these industry-leading products can support your requirements today and into the future.
-
Product
3U CompactPCI 5-Port Serial Ethernet, Optional POE Card
cPCI-A3ETH
-
- Follow PICMG® CompactPCI® Serial design guide- CompactPCI® Serial, 3U 4HP/8HP- 5x RJ-45 ports support up to 2.5G via Intel® i226IT Ethernet controllers- Optional PoE supported- Operating temperature: -40°C to +85°C- Designed to meet EN50155 standards
-
Product
I/O Extension Stack Board For DP, USB, And Audio Extension
PCE-SA01
-
I/O extension stack board1 DP, 2 USB 3.0, MIC-in, LINE-outDimensions (L x H) : 68 x 125 mm (2.67" x 4.92")Supports Model: PCE-3029, PCE-4128, PCE-4129Support Model: PCE-5029/5031/5032/ 5033/5129/5131/5132/5133/7129/ 7131/7132/7133; PCE-3029/3032/ 4129/4132
-
Product
Embedded Serial Triggering and Analysis for InfiniiVision DSOX1000 Series Oscilloscopes
DSOX1EMBD
-
The IC, SPI, and UART/RS-232 serial decode option for InfiniiVision 1000 X-Series oscilloscopes (DSO models) displays responsive, time-aligned, on-screen decode of Inter-Integrated Circuit (IC), 3-wire Serial Peripheral Interface (SPI), and UART/RS232 serial communication buses. Because it is hardware-based, this option provides the fastest throughput solution for triggering on and analyzing IC, SPI and UART/RS-232 serial buses found in a wide variety of embedded designs.
-
Product
FMC 5-Channel Digital I/O Module
FMC DIO
-
Sundance Multiprocessor Technology Ltd.
The fmc-dio-5chttla 5-channel digital I/O module is a simple board for digital I/O on LEMO connectors. It has been designed for testing White Rabbit functionality as part of the SPEC Demonstration Package for White Rabbit, and it can be used for other general purpose applications too.
-
Product
3U CompactPCI 8-port Serial Communication Module
cPCI-3548
-
- Supports 32-bit/33MHz CompactPCI bus- 16C550A compatible serial communication controller- Eight RS-232/422/485 asynchronous communications ports with intelligent buffer- 2500 VDC signal to ground isolation voltage- Auto-flow control; change mode by dip switch- Plug-and-play, IRQ & I/O address automatically assigned by PCI BIOS, shared IRQ- Surge protectors; rugged DB-62 connector
-
Product
1-Ch SSI Absolute Encoder EtherCAT Slice IO Module
AMAX-5082
-
Encoder Type: SSI (Binary / Gray code)Latch Counter ValueComparator *2Compare trigger Output *2
-
Product
SH25F-25M-1 25-Pin Female to Male Shielded I/O Cable, 1 m
192568-01
-
SH25F-25M-1 25-Pin Female to Male Shielded I/O Cable, 1 m
-
Product
8-port Serial Interface, Modular, With/without Optical Isolation, 3.3V/5V
APCIE-7800
-
The APCIE-7xxx series of ADDI-DATA allows you to implement either 1, 2, 4 or 8 modules on serial interface boards.
-
Product
I/O Board With Two COM, Four USB 2.0 And Audio For PICO312, PICO313, PICO511, PICO512
AX93A09
-
*Specification: 1 x RS-232/422/485, 1 x RS-232, 4 x USB 2.0, 1 x Audio (MIC-in/Line-out), 1 x Power-on, 1 x Reset, 2 x LED*Dimensions: 118 x 29 mm*Compliant products: PICO312, PICO313, PICO511, PICO512
-
Product
3U CompactPCI Serial 7-slot SSR w/o RTM w/ Ethernet
1CPCIS-307-R100
-
3U CompactPCI Serial Backplane with 7 CompactPCI S.0 slots, system slot right, without rear IO: 1x CompactPCI S.0 CPU, 6x CompactPCI S.0 peripheral slots, without connectors for RTMs, Ethernet single star from system slot to all peripheral slots.
-
Product
Remote I/O
-
ADLINK remote IO and serial communication cards are suitable for handling multiple digital signal types for IoT and other industrial applications such as facility monitoring, environmental monitoring, and industrial process control.Remote IO - NuDAM modules provide direct communication with various sensors, including performing signal conditioning, scaling, linearization and conversion to obtain temperature, pressure, flow, voltage, and current measurements. The new ND6100 series modules use Modbus/RTU remote data transmission protocols, providing customers with a comprehensive product portfolio. ADLINK's serial communication cards provide a PCI/PCIe interface and support RS-232 and CAN communication interfaces, allowing customers to choose the most suitable communication card for various automation equipment needs.
-
Product
EtherCAT Extension Slice IO Module
AMAX-5079
-
Function: Conversion of EtherCAT to 100BASE-TX Ethernet for extension of the EtherCAT networkCable : Ethernet/EtherCAT cable (min. Cat. 5) shieldedDistance between stations : Max. 100 m (100BASE-TX)Bus Interface : 1 x RJ45Power from bus : N/A
-
Product
16-Ch Digital Input EtherCAT Slice IO Module
AMAX-5052
-
Channels:16Digital Input;Dry Contact;Logic level 1: close to Iso.GND;Logic level 0: open;Wet Contact;Rated voltage: 24VDC;Logic level 1: 10~30 VDC;and -10~-30 VDC;Logic level 0: -3~3 VDCInput Delay:From logic level 0 to 1: 4ms;From logic level 1 to 0: 4msDigital Filter: 3ms
-
Product
Enhanced 16 Discrete/Switch I/O Channels (±80 V, 625 mA/Ch.)
DT5
-
The DT5 module (the enhanced version) features 16 independent, isolated, programmable channels that can be used for input voltage measurements (±80 V), or as a bi-directional current switch (up to 500 mA per channel). When programmed as a switch with the switch closed, both the current through the switch and the voltage across the switch can be monitored. These modules include diode clamping on each channel. Clamping is useful for inductive loads, such as relays and short circuit protection. Additional features of the DT5 (Enhanced Version) are listed below.
-
Product
16-Ch Isolated Digital Input And 16-Ch Relay USB 3.0 I/O Module
USB-5862
-
USB 3.0 SuperSpeedDaisy chainable by built in USB hub16-ch Isolated Digital Input and 16-ch Form A-type Relay OutputWide input voltage range (10 ~ 30 VDC)High-voltage isolation on input channel (2,500 VDC )Quick removable European type connectorLED indicators for I/O statusSupported operating systems: Windows 10/11
-
Product
Industrial I/O Module
DIO-3460
-
The DIO-3460 is a space-saving industrial I/O module. It provides for save cable connections due to the use of WAGO Cage Clamp connectors rather than screw terminals.
-
Product
Rugged Deployable, Rackmountable Chassis For 3U Cards Aligned To SOSA Or CPCI Serial
20037765
-
This unit is a rack-mountable, rugged deployable chassis for use in harsh environments. The chassis has been designed to provide modularity and flexibility to support the full design life cycle of a system from initial concept and lab development through to qualification and full platform deployment.
-
Product
A PoE-PD I/O Board
AX93274
-
*PoE-PD I/O board complies with IEEE802.3at standard via an internal cable to power on SBC*100 x 32 mm*1 x LAN cable, 1 x power cable, 1 x thermal module*Compliant products: PICO831, PICO121, PICO841, PICO843
-
Product
6AI/2AO/2DI/2DO IoT Modbus/SNMP/MQTT Ethernet Remote I/O
ADAM-6024
-
6ch analog input/2ch analog output/2ch digital input/2ch digital outputProtocols:MQTT(TLS),SNMP,Modbus TCP,RESTful API,ASCIIGCL to perform basic logic control rulesPeer-to-Peer function to map I/O statusWatchdog timer to recover the systemIsolation protection: 2000VDCBuilt-in web server
-
Product
I/O Input Board
VME-3123A
-
16-Bit High-Throughput Analog Input Board, 16 Channels with Simultaneous Sample-and-Hold Inputs
-
Product
8-Ch Digital Input (2-Ch Timestamp & 6-Ch Without Timestamp) EtherCAT Slice IO Module
AMAX-5051T
-
Precise and Deterministic Digital Input2-ch Timestamp Digital Input6-ch Regular Digital InputTimestamp resolution: 1nsRising Edge & Falling Edge DI Latch
-
Product
PoE-PSE I/O Board
AX93280
-
*PoE-PSE I/O board complies with IEEE802.3af standard via an internal cable connected to LAN port on a SBC to power an external PoE device
-
Product
Serial Production Mark Quality Control
-
The control system is based on the Sick IVC smart camera, which not only captures, but also processes the image. After training on the font samples, the system practically does not require the operator's attention in addition to setting the current marking for control. The character set can be specified by the operator or transmitted via the interface from the printer or from the enterprise information system.The camera software works autonomously: it loads all settings from the camera's permanent memory, initializes the backlight electronics and waits for a signal from the object presence sensor. When a signal is received from the sensor (an object in the shooting area), the camera captures the frame, searches for markings and analyzes the symbols for their compliance with the exemplary set.
-
Product
1-Port EtherCAT I/O MainDevice MPCIe Card
PCM-26R1EC
-
Meets Advantech iDoor technology standardPCI ExpressR Mini card specification revision 1.2 compliantIdentical interface for all EtherCAT Motion CotrollersSupport high speed IO control in EtherCATConnect I/O SubordinateDevice automatically without ESI/ENIEasy-to-use EtherCAT integrated development environmentProvide error detection and diagnostics to monitor the entire EtherCAT network
