Filter Results By:
Products
Applications
Manufacturers
-
product
Concrete Tester & Surveyor
CTS-02V4
CTS-02V4 (Concrete Test and Surveyor) is a Non-destructive testing device for estimation of compressive strength of concrete. CTS estimates the compressive strength of concrete based on Mechanical Impedance Method by measuring a waveform of impact force with an accelerometer which mounted on the hammer unit.
-
product
Moisture Testing
Determine moisture in concrete and other construction materials. Meter for rapid determination of moisture content in sand and other fine or coarse aggregates. moisture content in Solid Materials. Includes Meter, Test Cable and Case. Meter for the Rapid Determination of Moisture Content in Different Types of Soil. Determination of Water/Cement Content Ratio in Fresh Concrete. (Type R for Regular Water Cement Ranges. Type L for Low Water Cement Ranges.)
-
product
Concrete Comprission Testing Machine
CONCRETO 2000X/3000X
CONCRETO Series This compression testing machine can safely and efficiently perform tests at a high capacity without causing explosive fracture (failure of the specimen) on ultra-high-strength concrete, which is used as a structural material in high-rise buildings, etc. This one machine can be used for materials ranging from ultra-highstrength concrete to specimens that have been recently cast, mortar, etc.
-
product
Concrete Moisture Test Meter
Rapid RH 4.0 EX
The Rapid RH 4.0 EX concrete test is superior to all other humidity measurement systems on the market today. Rapid RH 4.0 EX concrete moisture tests equilibrate faster than other concrete moisture tests. The reading taken one hour after installation for concrete relative humidity content will be within 3% of the final reading.
-
product
High Voltage Porosity Detection
High Voltage Technique: The high voltage, or porosity technique, can be used to test coatings up to 25mm (1”) thick and is ideal for inspecting pipelines and other protective coatings. Coatings on concrete can also be tested using this method.
-
product
Concrete Humidity Sensor
BlueRock
BlueRock is a rugged, waterproof sensor designed to wirelessly monitor the relative humidity and temperature of concrete from fresh to hardened stages.
-
product
Field Machine
The Portable Field Machine is our most versatile full specification corrosion testing instrument. Its rugged construction and protective water resistance IP68 enclosure enables it to be operated at extreme locations throughout the world. This instrument takes laboratory precision outdoors to oil rigs, pipelines, concrete walls and just about anything that needs corrosion monitoring in situ. The potentiostat, ZRA, integral Frequency Response Analyser and Sweep Generator are exactly as provided in the laboratory Gill 8 model ensuring the most accurate testing available. The choice of tests is not limited; the AC, IR Compensation and DC tests plus the Sequencer and Analysis that are supplied with this field instrument are the same as supplied with the laboratory instruments.
-
product
Resistivity Meter for Concrete
Ohmcorr Test System™
OhmCorr has two probes spaced 1.97" (5cm) apart which are placed in holes drilled to a depth of 3/8th" (8mm) and filled with conductive gel. The direct digital read-out of resistivity is displayed on the LCD when the control switch is activated. OhmCorr and CorMap, when used together, provide an economical and sound diagnostic system of corrosion in reinforced concrete.
-
product
Environmental Rooms
Darwin Chambers Company designs, manufactures, installs, and services custom chambers of all types and sizes, for a wide array of applications, including: GMP Shelf-Life Testing and Storage, Dry/Moist and Cold Storage for Seed and Agricultural Products, Nutritional Supplements, General Materials Testing, Mold and Fungal Incubation, Photography Storage, Concrete Curing, Roll-In Bottle Incubation Chambers and Compliant Vivariums (NIH, ALAAC, OLAW, USDA, etc.), more. We have pioneered a number of innovative, resource-saving technologies, from thermoelectric and liquid-circuited cooling systems to ultrasonic humidification.
-
product
Impact Echo SystemFor Field Evaluation of Concrete Structures
Vu-Con System
The Vu-Con Analyzer provides the engineer with the sturdiest, most reliable system for impact echo analysis. No moving parts and implementation of the latest microcomputer technology has created a system that is both sophisticated and reliable. The unit comes with a 90 mm (3.5?) by 115 mm (4.5?) graphic display screen that is easily viewed in daylight
-
product
Rebound Hammer
SilverSchmidt - PCN
Concrete test hammer SilverSchmidt Type PC N : *Standard impact energy (2.207 Nm) with PC communication, increased memory capacity and Hammerlink software*Use for concrete >10cm*Measuring range: 10-100N/mm2
-
product
Rebound Hammer
SilverSchmidt - STN
Concrete test hammer SilverSchmidt Type STN : *tandard impact energy (2.207 Nm) without PC communication*Use for concrete >10cm*Measuring range: 10-100N/mm2
-
product
Concrete Hardness Tester
W-C-7312
It is recommended that calibration of the test hammers be checked regularly usually after about 2000 strokes.The James Calibration Anvil (W-C-7312) has been designed for just that purpose.
-
product
Concrete Water Impermeability Tester
The concrete water impermeability testing system is designed with many different standards in mind including DIN 1048, ISO/DIS 7031, EN-12390-8 & UNI 9533. This impressive piece of machinery comes in different models with either 3 or 6 measuring points and with or without quantitative measurement of water permeability. The supporting structure is very stable and is at a convenient height to allow the easy access. The pans are made out of stainless steel, the specimens are easy to insert due to the clamping device.
-
product
Digital Test Hammers
James Instruments? digital test hammers are an advanced, completely automated system for estimating concrete compressive strength. Its calculation, memory and recording functions allow for quick, easy and accurate test results.
-
product
Digital Strain-Gauge Transducer
ZET 7010 DS
Digital small strain gauge sensor ZET 7010-DS transducer is purposed for tensile-compression control of concrete structures, it is used in SHM (structural health monitoring systems). These transducers can be used in stationary and mobile SHM systems.
-
product
Diametral Extensometers for Rock and Concrete Testing
Model 3975
Jinan Testing Equipment IE Corporation
Designed for accurate measurement of small diametral strains such as those required to determine Poisson’s ratio of rock, concrete and asphalt samples. The units are designed to be used in conjunction with the Model 3542RA axial averaging extensometer.
-
product
Concrete Strength Testers
This category of products comprises the range of instruments utilized to evaluate construction material strength. The range of instruments is typically considered to be two parts. The first are non-destructive field tests of compressive strength. The second are tensile field tester systems to either determine the tensile strength of an overlay or bond material, or tensile strength of anchors embedded in the concrete. The first group is pure Non-Destructive Testing where the strength of the material is determined by correlation to another parameter more easily available and readily apparent. This is typically the hardness of the concrete or the resistance to penetration by either a pin or probe. The Windsor Probe, Windsor Pin and our line of Rebound Hammers all fall within this category. These are widely used standard tests and as such have seen use throughout the world.
-
product
Metal Detectors
Zircon’s MetalliScanner® metal locators are designed with both the professional contractor and DIYer in mind. Wether you need to find rebar in concrete, pinpoint smaller metal targets like nails, or locate live AC electricity, Zircon has a tool for your metal detection needs.
-
product
Utility Locating with LMX GPR
LMX200™
Unprecedented insights and target confidence. Detect traditionally non-locatable subsurface features:Non-metallic pipes, including PVC and asbestos cementConcrete storm and sewer systemsUtilities where installed tracer wiring has failedUnderground storage tanks and drainage tilesSeptic system componentsNon-utility structures such as vaults, foundation walls and concrete pads
-
product
Environmental Test Chambers
TTC/CTC
Rapid, precise and energy-saving temperature changes in the range from -42 C to +190 C, along with fast humidity recovery times, make the TTC temperature test chamber and the CTC climatic test chamber with humidity unit a perfect duo for controlled material testing, function tests, ageing tests or climate tests on composites, concrete, plastics or electronic components in material technology, the automotive and aerospace industries, and electronics.
-
product
Remote Slab Sensor and Outdoor Temperature Sensor
CHV-RSS
The CHV-RSS is a remote temperature sensor designed for use with select Crestron thermostats. Ideally suited for concrete slab, under floor, or any outdoor installation, the CHV-RSS is an extremely accurate temperature sensor potted within a rugged waterproof stainless steel sleeve.
-
product
Pine Test Equipment
Pine Test Equipment, Inc. has been serving the materials testing industry for more than 40 years. The well-engineered equipment, sales, service, field service techs and technical support staff have earned the company an unprecedented reputation known around the world. In addition to asphalt, the company also sells concrete testing systems.
-
product
Profoscope
Proceq Profoscope series coverometers allow immediate location of reinforcement and measurement of the concrete cover; once the instrument has been positioned in an optimal position, with a simple click you can also obtain the estimate of the diameter.
-
product
Strength Testing of Concrete, Brick and Mortar
Windsor Pin System
Measures the compressive strength of concrete, mortar and brick in-situ, quickly, accurately. A non-explosive instrument, the Windsor Pin System uses a spring-loaded device to drive a steel pin into the concrete or mortar.
-
product
Concrete Imaging with Ground Penetrating Radar GPR
Conquest 100
Conquest GPR: Get rapid, reliable results and reduce the need for destructive testing. Conquest GPR is a light, portable device that provides a fast, non-invasive method to gain accurate insights of objects below the concretesurface, even on a curved surface or column. Conquest GPR reduces risk by detecting rebar, post-tension cables, metallic and non-metallic conduits as well as current-carrying wires embedded in concrete. Once your concrete scan is complete, Conquest GPR connects to your mobile device, allowing you to email information directly from the field. Back in the office view your data and make client-ready reports in minutes.
-
product
SmartRock™ Plus
SmartRock™ Plus is a solution offered by ready-mix producers that enables contractors to monitor the strength and temperature of early-age concrete in real time. Contractors install wireless sensors on the rebar, then monitor real-time temperature and strength results on the iOS or Android app for quick decision-making during the concrete curing process.
-
product
Analogue Concrete Test Hammer
181
The Elcometer 181 Analogue Concrete Test Hammer provides a quick, simple and inexpensive method for non-destructive evaluation of concrete compression strength and other masonry materials.
-
product
Humidity and Temperature Moisture Inert and Fresh Concrete
Non-destructive testing / Humidity and Temperature
-
product
Rebound Hammer
SilverSchmidt - STL
Concrete test hammer SilverSchmidt Type ST L : *Standard impact energy (0.735 Nm) without PC communication*Use for concrete <10cm and fragile rocks*Measuring range: 10-100N/mm2
