Filter Results By:
Products
Applications
Manufacturers
-
product
16 channel 16 bit Digital to Analog
CPCI-DA16-1
The CPCI-DA16 is a slave Digital to Analog board that is managed by the host processor on the CPCI bus. The card contains a state machine that performs mostof the work of outputting data, in order to minimize the impact to the HOST system. The CPCI-DA16 is supported by ALPHI Technology under Windows NT by a Board Support Package which is supplied with the card. Other documentationsupplied with the card will describe this support in full detail.
-
product
32-CH Sinking Type Digital Ouput EtherCAT Module
EPS-2132
ADLINK" s EPS slave system features modular design for flexible high channel density, rugged construction, easy maintenance, and intelligent performance, compatible with 3rd party EtherCAT products. Precise time-deterministic control enables I/O synchronization for critical applications, and FPGA and ARM technology allow users to fully monitor status of EPS modules and systems, including operating temperature and usage cycle of relay switching, as well as motion control status for general purpose motor drive control. In addition, the ADLINK EtherCAT configurator enables auto-scan and configuration across EtherCAT systems. The EPS" unique structural and electronic design supports hot-swappable function, reducing repair time, and the rugged construction and operating temperature range of -20°C to 60°C allow operation in the harshest environments.
-
product
PXI Automotive Ethernet Interface Module
The PXI Automotive Ethernet Interface Module communicates with Automotive Ethernet so that you can use the NI‑XNET driver or standard networking drivers to develop applications that require Automotive Ethernet to test and validate automotive electronic control units (ECUs). It provides up to four independent endpoints or up to two network terminal access points (TAPs). With onboard hardware timestamping and the ability to act as 802.1AS masters or slaves, the PXI Automotive Ethernet Interface Module can synchronize with an external network as well as the rest of a PXI system.
-
product
Digital I/O PXI Card
GX5290
The GX5290 Series are a high performance, cost-effective 3U PXI dynamic digital I/O boards offering 32 TTL or LVDS input or output channels with dynamic direction control. The GX5290 Series also supports deep pattern memory by offering 256 MB of on-board vector memory with dynamic per pin direction control and with test rates up to 200 MHz. The single board design supports both master and slave functionality without the use of add-on modules.
-
product
16-Axis PCIe EtherCAT Master Motion Controller
PCIe-8332
ADLINK PCIe-8332 is a hardware-based EtherCAT motion controller able to support up to 16 synchronized axes and over 10,000 points simultaneously. The PCIe-8332 features dedicated isolated emergency stop input (EMG), and configurable isolated high-speed digital input as not only generic sensor input but also pulsar input, with up to 1MHz input frequency. Optimum jitter control is provided in minimal cycles of 250µs to optimize synchronous I/O performance for vertical automation applications in semiconductor, electronic manufacturing, and others. The PCIe-8332 provides an out-of-shell application-ready (APS) function library to generate multi-dimensional, highly synchronized, time-deterministic event-triggered motion & I/O control. A wide range of compatible 3rd party slaves are easily designed with ADLINK's APS function library. ADLINK's MotionCreatorPro 2 utility is fully compliant with the Microsoft Windows environment, that allows complete EtherCAT motion and I/O configuration and function evaluation as well as compiling program download functions.
-
product
PXI CANopen Interface Module
The PXI CANopen Interface Module is a high-speed CANopen interface for developing applications with the NI-Industrial Communications for CANopen driver. CANopen is the application layer that sits on top of the CAN physical layer often used for industrial automation applications. The PXI CANopen Interface Module can transmit/receive PDOs and SDOs according to CiA DS301. It also features a batch SDO editor with electronic data sheet (EDS) file integration and layer setting services (LSS) support for slave node configuration.
-
product
Exerciser with SMBus Support
Summit Z3-16
The Summit Z3-16 with SMBus Support is a critical test and verification tool intended to assist engineers in developing and improving the reliability of their systems. The Summit Z3-16 with SMBus Support can emulate PCI Express root complexes or device endpoints, allowing new designs to be tested against corner case issues. In addition, it can emulate SMBus traffic as a master or slave.
-
product
Raptor HV High Voltage Tester
The Raptor-HV, also called the high voltage slave, is an optional product that extends the Raptor’s applications to tests that require the use of a moderately high AC voltage.
-
product
AT Command Master+Slave / Central+Peripheral
AT command module serie
Raytac's AT command module series comes with AT command firmware pre-programmed which helps developers enjoy a Design Saving & Time-To-Market journey.
-
product
MTM-Bus Tester
PXIe-1149.5
The Corelis PXIe-1149.5 is a versatile, multi-mode instrument for interfacing with MTM-Bus modules. The PXIe-1149.5 adds MTM-Bus master, slave, and monitoring with full IEEE-1149.5 electrical and protocol compatibility with a standard PXIe interface for convenient integration into any Test Program Set (TPS).
-
product
High Performance 335 M, 6 Channel Digital Receiver
DP-VME-5838
The DP- VME-5838 is a VME64x slave, high performance 335M, six channel Digital receiver card. It samples and down converts the analog IF signals into the digital base band data. The processed I/Q data are pulse compressed and decimated to the base band rate. In the Central Unit system, this pulse compressed I/Q data has to be sent to the signal processing unit through a 2.5G speed Optical SFPDP link.
-
product
MIPI Soundwire Total IP Solutions
Soundwire
Soundwire is suited for small, cost-sensitive audio peripherals such as modern digital class-D amplifiers and digital microphones. The Total MIPI SoundWire IP Solution from Arasan enables early adopters the fastest path to adoption of this new standard by offering a comprehensive IP package that includes the Verilog RTL source code for Master and Slave, fully validated for compliance with the standard, a comprehensive test environment with a compliance suite for verification of the IP package, a SoundWire Hardware Development Kit (“HDK”) for FPGA prototyping, a SoundWire protocol analyzer and a complete SoundWire software stack.
-
product
EOC Slave
EOS-204W
Hangzhou Softel Optic Co., Ltd.
EOS-204W is the EOC slave based on HomePlug AV solution for Ethernet access over coax. It works together with EOC master which is based on HomePlug AV solution as well to construct a two-layer Ethernet data transmission channel on CATV coax cable, provide the Ethernet access service based on the existing coax cable networking. EOS-204W is the slave with 4 Ethernet ports and WIFI.
-
product
General Purpose I/O Modules
HY-TTC 36X
HY-TTC 36X is a CANopen-based, cost effective, modular and user-friendly solution for extending the number of I/Os in mobile applications. This controller is best suited for different kinds of control tasks in a vehicle and acts as slave unit in a CAN-based network architecture.
-
product
12C Adapter Slave
USB I2C adapter MS
*Plug & Play*No additional driver necessary*HID device drivers are included in major operating systems*Open interface description enables communication without a DLL
-
product
32-CH Discrete Output Module
HSL-DO32-M-N/HSL-DO32-M-P
Slave ID consumption: 2 consecutive from odd"N" type for NPN sinking type outputSwitch capacity: Single channel 500 mA; all channels 60 mA at 24VDCPhoto couple isolation voltage: 2500 VrmsResponse time: ON→OFF: 180µs, OFF→ON :1.2µsLED indicator: Power, Link and Output statusPower supply: +10V to +30 VDCOperating temperature: 0 to 60°C
-
product
Modbus Data Acquisition
The Datexel range of Data Acquisition equipment includes Modbus RTU Masters and Slaves, Modbus Input, Modbus Output Modules, Modbus Isolation Modules and Modbus Repeaters. The range also includes converters (RS485, USB, RS232, RS422, TCP-IP). By combining these units with the DAT3000 and DAT10000 series a complete solution for your Data Acquisition can be found from Datexel. The DAT9550 is a remote Modbus display unit that can be programmed to accept data from Modbus slaves or masters such as a PLC or the DAT9000 range of Modbus controllers.
-
product
Ethernet To Modbus RTU Interfaces
ICS's Ethernet to Modbus Interfaces provide Modbus TCP/IP to Modbus RTU serial conversion and Raw Socket (Telnet) to control Modbus RTU Slave Devices. Available in small Minibox™ and OEM board formats. OEM board has Ethernet, GPIB and USB interface ports. All Interfaces include the VXI-11 protocol for use with: LINUX, UNIX, SunOS, Apple OS X, HP-UX, IBM-AIX and Windows 2K or later Windows systems.
-
product
Single 8-Channel 1-Pole 16 Amp PXI Power Multiplexer
40-662-013
The 40-662 range of 16 Amp PXI power multiplexer modules is available in seven configurations ranging from 4-off 2:1 multiplexers to 1-off 16:1 multiplexers. Power multiplexer modules are intended for switching heavy AC or DC loads or for the slave switching of large external relays, contactors and solenoids. All versions are suitable for switching loads up to 16 Amp at 250VAC. User connections are made via a 20-way GMCT plug which is fully support by our comprehensive range of cables and connector accessories.
-
product
Quad 2-Channel 1-Pole 16 Amp PXI Power Multiplexer
40-662-011
The 40-662 range of 16 Amp PXI power multiplexer modules is available in seven configurations ranging from 4-off 2:1 multiplexers to 1-off 16:1 multiplexer. Power multiplexer modules are intended for switching heavy AC or DC loads or for the slave switching of large external relays, contactors and solenoids. All versions are suitable for switching loads up to 16 Amp at 250VAC. User connections are made via a 20-way GMCT plug which is fully support by our comprehensive range of cables and connector accessories.
-
product
4-Channel High Speed Position Comparison and Trigger Module
ECAT-TRG4
The ECAT-TRG4 is EtherCAT slave module with high-speed position comparison trigger and encoder single redriver function, helping machine and equipment builders to use multiple triggers simultaneously for AOI, glue dispensing, display tests, and storage assembly applications.
-
product
4-Channel Motion Control and High-Speed Trigger and Module for the Bridge Connected to EtherCAT
ECAT-4XMO
The ECAT-4XMO is EtherCAT slave module with high-speed position comparison trigger and encoder single redriver function, helping machine and equipment builders to use multiple triggers simultaneously for AOI, glue dispensing, display tests, and storage assembly applications. Additionally, the ECAT-4XMO has 4-axis motion control with bridge function between EtherCAT and non-EtherCAT. Advanced motion control functions help machine and equipment builders to increase their motor selection portfolio, like leaner, step, servo, direct drive, and AC motors, making it ideal for a variety of automation industry applications.
-
product
Quad 4-Channel 1-Pole 16 Amp PXI Power Multiplexer
40-662-001
The 40-662 range of 16 Amp PXI power multiplexer modules is available in seven configurations ranging from 4-off 2:1 multiplexers to 1-off 16:1 multiplexer. Power multiplexer modules are intended for switching heavy AC or DC loads or for the slave switching of large external relays, contactors and solenoids. All versions are suitable for switching loads up to 16 Amp at 250VAC. User connections are made via a 20-way GMCT plug which is fully support by our comprehensive range of cables and connector accessories.
-
product
GPS Wireless Clock
Signals & Systems India Private Limited
GPS Clock offers an easy, cost-effective solution for accurate, synchronized time displays without expensive, disruptive installation procedures. Because there are no wiring requirements, installation times are drastically reduced. It is ideal for renovation projects, as there is no need to worry about installation work, as well as new construction. The GPS clock can be synchronized through GPS Antenna or Wireless Antenna. The display can be wall/panel / tabletop mountable. It can be used as a wireless clock to synchronize many wireless slave clocks in and around the buildings.
-
product
PXI General Purpose 2A Relay Module 16xSPDT, 78 D-sub
40-131-101
Low cost, general purpose electromechanical relay cards suitable for use where reed relay based switching cards do not have sufficient voltage or current carrying capability. Applications include switching of medium power AC and DC loads or slave switching larger relays, contactors or solenoids. Connections are made to the card via a front panel mounted 50 or 78 pin D-Type connector plug.
-
product
PCI Express to VME interface
SIS1100e/3104
Single width 6U VME master/system controllerred ball, 1/2/4 GBit/s optical link, red ball, up to 450 m link distance, red ball 128 MBytes memory (PPC Ethernet or VME slave)
-
product
EOC Slave
EOS-204
Hangzhou Softel Optic Co., Ltd.
EOS-204 is the EOC slave based on HomePlug AV solution for Ethernet access over coax. It works together with EOC master which is based on HomePlug AV solution as well to construct a two-layer Ethernet data transmission channel on CATV coax cable, provide the Ethernet access service based on the existing coax cable networking.
-
product
Modbus Simulator & Tester
Modbus Poll
Modbus Poll is a Modbus master simulator designed primarily to help developers of Modbus slave devices or others that want to test and simulate the Modbus protocol. With the multiple document interface you can monitor several Modbus slaves and/or data areas at the same time. For each window you simply specify the Modbus slave ID, function, address, size and poll rate.
-
product
GPS Synchronized Clock Systems
Signals & Systems India Private Limited
GPS synchronized clock system offers accurate time to all clocks in the system. The GPS clock synchronization system consists of a master clock and multiple slave clocks. The master clock communicates with all the salve clocks via wired/wireless medium in the system to provide them with an accurate time source. The objective of the GPS synchronized clock system is to make sure that all clocks in the system display the same time. Regardless of which part of the building you are in, the time shown by the clocks will be uniform and accurate.
-
product
VME Analog Input Module
DP-VME-1427
The DP-VME-1427 is a standard 6U VME based general purpose 32 channel Analog to Digital Convertor (ADC) module. The module is a slave VME 64x interface, that responds to A24/D16 standard VME address cycle. On-board auto-conversion circuitry performs all the task related to multiplexing, sampling and converting of analog input signals to the digital outputs.
