Strain Gauge Amplifiers
-
Product
5B Measuring Amplifiers
MA Series
-
Highest aim of our connection technology is user-friendliness. Very comfortable is the connection of our products to the most various sensors and signals.
-
Product
VME PWM Servo Motor Driver / Amplifier Board
64PW2
Servo Motor Drive
NAI’s 64PW2 is a 6U VME Servo Motor Driver/Amplifier Board featuring a dual, four-quadrant, bi-directional, PWM servo amplifier. Specifically targeted for DC servo motor applications, this board has an amplified power stage that uses a Pulse Width Modulation (PWM) control signal to provide motor control for both brush and brushless motors. Each motor drive accepts a 65 VDC power input and provides a 5 Amp maximum continuous current output (8.5 Amp peak).
-
-
Product
Wide Range Vacuum Gauge
HVG-2020B
-
The HVG-2020B wide range, dual sensor vacuum gauge takes measurement to the next level. With a Piezo based sensor and a thermal based Pirani sensor accurately and confidently measure pressures across seven decades. The Piezo sensor is media isolated, gas composition independent, and periodically zeroed by the Pirani sensor. An ambient thermal sensor enables the instrument to adjust for temperature and therefore better accuracy.
-
Product
Loop Powered Trip Amplifier With Dual Relay Output
SEM1636
-
The SEM1636 monitors a (4 to 20) mA loop and provides two independent change over trip contacts set to trip at any point within the (4 to 20) mA range.
-
Product
Analog Distribution Amplifier
DA 1:54
-
The DA 1:54 Analog Distribution Amplifier is designed to make it simple to distribute analog signals generated by Spectrum products to multiple locations and to overcome long cable runs. The DA 1:54 consists of three separate amplifier sections that are factory- configured to operate independently or ganged together, depending upon requirements.
-
Product
Single Channel High Voltage Linear Amplifier
A400
-
The A400 is a general purpose broadband linear amplifier having a fixed amplification of 20 times and capable of bipolar high voltage output of 200. Any functiongenerator or arbitrary waveform generatoror any othe signal source with amplitude up to 10 V can be used as an input device. The amplifier's output is linear from DC up to megahertz range. It can be used in a wide range of applications, for example to drive piezo actuators, MEMS, OLEDs, liquid crystals, etc.
-
Product
Erbium Doped Fiber Amplifier
EDFA
-
EDFAs are based on the light amplification in erbium-doped fiber, which are optically pumped by means of 980 nm or 1480 nm light sources. In this way, the light of a larger wavelength within the C or L band applied to the input of the amplifier is amplified, thus widening the range of optical communication links. EDFAs typically operate in saturation and the average signal power determines the average gain. The dynamics of EDFA are unaffected by the sequence and dynamics of a digital signal or channel interaction in DWDM systems. As a result, multiple channels can be bundled within the total erbium spectral amplification bandwidth. However, the total average output power in both cases is determined by the saturation power of the specific EDFA.
-
Product
Premium Wireless Vacuum Gauge Probe for use with HUB8 or HUB6
WVG2
-
UEi Test & Measurement Instruments
Premium Wireless Vacuum Gauge Probe
-
Product
Crossed-Field Amplifiers
CFAs
-
Communications & Power Industries
CPI BMD’s crossed-field amplifiers (CFAs) are broadband, phase-stable microwave amplifiers used in coherent radar chains to efficiently generate very high peak output powers from relatively low input voltages which can be either applied to the cathode or an electrode similar to a TWTs cathode or grid pulsing, and in relatively small, lightweight packages. These characteristics make CFAs particularly well-suited for applications in which the transmitter must be either airborne, transportable, mobile or portable.
-
Product
Broadband Power Amplifier
PAS-08025-200
-
* Solid State Power Amplifier* Small Signal Gain: 50 dB typ.* Rack Mount Case (Optional)* Internal Cooling Fans* Type N Connectors
-
-
Product
Fiber Amplifier - Node With Supply
FANS 811-812
-
- AGC - Automatic Gain Control- Higher RF at next connected Node- Maintain MER/BER for Digital FTTH Transmission- High Quality DFB Lasers with Isolators- Variable SLOPE/GAIN Control- Input Wavelength : 1310/1550nm- Output Wavelength : 1310nm- Digital Display of Optical Level- External FusesPower Options :- Mains 220VAC, 50Hz- 12V DC / 2 Amp- 40VDC from “40V/RF out” connectors
-
Product
150 kHz-230 MHz Broadband Power Amplifiers
-
Output power up to 80W for standard conducted immunity testing. Our 150 kHz-230 MHz amplifier range covers output power ranging from 20 W to 80 W.
-
Product
Gauge Type T Thermocouple Wire
W-TW-44TEF
-
Most thermocouple wire used in the manufacture of sensors is "Special Limits" wire which, to meet NIST standards, must be accurate to 0.5°C in the range 0-50°C. This means that even with most sophisticated electronics, the best possible accuracy for the system is 0.5°C.
-
Product
Signal Conversion Box for Linear Gauge Sensor
DG-0010/0020
-
This is a signal conversion box to convert 2-phase signals (TTL) from the linear gauge sensor GS/BS series into open - collector (DG-0010) or line driver (DG-0020) .This conversion box allows direct connection with the PLC *. It can also be transmitted over long distances.
-
Product
Transimpedance Amplifiers
-
Advanced Science and Novel Technology, Co., Inc.
Broadband transimpedance amplifier for low noise receiver side applicationsFeatures automatic input offset control and a peak detector8GHz of analog bandwidth for limiting of input data60dB of transimpedance differential gain15pA/sqrtHz of input referred noise density (0.1 to 10GHz)CML output interface with 50 termination and 225mVp-p single-ended swingSingle +3.3V power supplyPower consumption: 250mWExhibits low jitter and limited temperature variation over industrial temperature rangeUnpackaged bare die
-
Product
Tone Amplifier And Tone Generator Set
AM5/TG5xs
-
The New Tone & Amp Set are state of the Art Testers offering touch button technology, visual qTrace (quick trace) as well as audio tracer tone technology providing accurate wire location, high output volume and sensitivity, tone tracker functionality, Visual/Audible indication of Digital Traffic, filtered amplification with multiple volume levels and two normal tones and four tonetracker tones with constant and variable interrupt rates, short detection and indication, capacitive output connection, Quick change battery and low battery indication in New custom designed High impact resistance enclosures, fully sealed to IP67.
-
Product
Reference plus Comparator or Amplifier
-
Analog Devices reference plus comparator or amplifier products combine the excellent initial accuracy and low overtemperature drift performance of single function voltage references with comparators, buffer amplifiers, and current sense amplifiers. These products offer compact solutions for a broad range of applications such as battery monitoring, threshold detectors, window comparators, auto power-off circuits, and low dropout (LDO) regulators.
-
Product
Solid State Power Amplifiers
SSPAs
-
Communications & Power Industries
- Ruggedized for use in pulsed airborne, naval and ground radar- Found in weather forecasting Doppler radar systems- Utilized world-wide in air traffic control and precision approach radar systems
-
Product
RF Amplifiers up to 1000 MHz
-
Narrow and Broad band high power RF modules and rack mount amplifier systems using solid state devices including LDMOS and GaAs in Class A and Class A/B topologies for Pulse, AM, FM, continuous wave and digital modulation applications that include EW, Radar, Jamming, EMI and EMC radiated immunity, and wireless communications testing.
-
Product
Tool, Inspection Depth Gauge, Mini Coax, Receiver
910121156
Inspection Tool
Used to verify the depth setting of the center conductor of receiver mini coax contacts.
-
Product
Overdrive Protected Amplifier
-
RF Lambda’s line of overdrive protected amplifiers incorporate a technology which eliminates the need for a limiter to protect the amplifier from damage. High input powers up to 10W can be injected in the amp without damage. Hermetically sealed options are available upon request.
-
Product
Waveform Amplifiers
-
Most waveform generators are limited to 20V pk-pk EMF output level. The WA301 waveform amplifier can be used to increase that level up to 30V pk-pk.
-
Product
A-/B-Scan Thickness Gauge For NDT
SONOWALL® 70
-
SONOWALL 70 is the first thickness gauge in the market with intelligent probe identification. The extended probe management allows probe-specific information such as DAC-curves, delay lines, and serial numbers to be saved directly in the ultrasonic probe. In addition to various thickness applications, the device can be upgraded to a full-function flaw detector.
-
Product
L-Band Separate Raman Fiber Amplifier
RFA6000
-
Hangzhou Huatai Optic Tech. Co., Ltd.
1. Erbium-doped Fiber Amplifier, due to the multiple cascades and the accumulation of noise caused by spontaneous emission, will reduce the system CNR greatly and thus it will limit the transmission capacity and distance of the system. Raman Fiber Amplifier (RFA) is a newly designed fiber amplifier based on Stimulated Raman Scattering (SRS) effect. It is considered as the core technology of new generation DWDM fiber over-long communication. Compared with Erbium-Doped Fiber Amplifier, Raman amplifier has the advantage of low Noise Figure (NF), wider gain bandwidth, flexible gain spectral region and stable temperature. It is the only device that can operate in 1300~1600 nm.
-
Product
System Amplifier
SAM100
-
The R&S®SAM100 system amplifier is an ultra-broadband solid state microwave amplifier with a frequency range from 2 GHz to 20 GHz. With a power of up to 20 W, outstanding linearity and very good noise characteristics, the R&S®SAM100 amplifier is ideal as a compact system amplifier in various measurement setups e.g. design (DVT) and product validation test (PVT) or EMC. In measurement environments with R&S generators, frequency analyzers or network analyzers, they can act as drivers or boosters and amplify the measurement signals
-
Product
4 Channel Variable Gain Fast Amplifier
V974
-
The Mod. V974 is a 4 channel fast rise time amplifier housed in a 1-unit VME module; each channel features a voltage gain adjustable from 1 to 10 in x1 steps. Channels are non-inverting and bipolar: they amplify both positive and negative signals.
-
Product
Transimpedance Amplifiers
-
Current-to-Voltage Amplifier for use with Photodiode-Based Detectors. Transimpedance Amplifiers, Standalone Devices with Data Acquisition as well as Display Function (Optometer). Log/Lin Switching Amplifiers, etc.
-
Product
Non-Linear Pulse Amplifiers
-
These amplifiers have fixed output amplitudes, and are DC-coupled. All models can drive 50 Ohms or higher.
