Wire
See Also: Contacts, Harness, Connectors
-
Product
G12 - 12 Module Solution
-
For maximum versatility and easy access to instrument-side wiring and cable assemblies, VPC offers a selection of slide kits designed to fit most common rack depths. All slides are rated to support 180 lbs (81 kg) to accommodate even the largest fixtures. To order, measure rack depth between mounting rails. With this measurement choose the slide mounting kit that fits the rack. A rack extender kit is available for mounting to racks with recessed rails.
-
Product
PXI RTD Simulator Module, 8 Channel, PT500
40-263-402
-
The 40-263-402 is an 8-channel PT500 RTD Simulator. The 40-263 range is a cost effective method of simulating PT100, PT500 or PT1000 RTDs. It supports 4, 8, 12, 16, 20 or 24 channels in one or two PXI slots. Also, channels are able to be set as short or open circuit to simulate faulty wiring to a sensor.
-
Product
Cable Assembly, 50-Pin D-Type, Female to Unterminated With Cut Ends, 0.5m HV, Exit Away From Pin 1
A050DF4-C-HA050
-
50-Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24 AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assembly can be secured to the mating part by a screwlock. The 50-Pin Female connector options of this product can be directly mated to a corresponding Pickering Interfaces switching product.
-
-
Product
AC Voltage Detector
-
Triplett Test Equipment & Tools
high performance AC Voltage detector with adjustable sensitivity that has a wide measurement range of 25 to 1000ACV, Dual Color Tip to indicate low/high voltage, built-in flashlight and durable overmold. The high sensitivity allows it to detect low voltage AC wiring commonly found in doorbell circuits, thermostats, control circuits, and video surveillance camera power. The Sniff-It 3 is designed for industrial applications with its impact and drop resistance in a sleek ergonomic design, and the easy to use thumb wheel helps dial-in detection range. Includes (2) AAA batteries. CAT III safety rating.
-
Product
Instrument Grade Data Sensor
WISER 8000
-
TECAT Performance Systems, LLC
The TECAT WISER Model 8000 dual strain measurement and monitoring system is a wireless data acquisition system for measuring two external strain channels at high data rates up to 8kHz. The small, light, power-efficient, and non-invasive design enables strain measurements in a wide range of applications. With dual external sensor inputs two Micro-Measurements strain gauge bridges can be measured by a single system, for example to measure both thrust and torque loads simultaneously.The Model 8000 has a long range data transmission of >1,000 meters with up to +/- 0.025% FSR sensitivity for remote measurements. After initial setup using the WISER software interface, the system can be wired directly to your DAQ system, for seamless data collection.
-
Product
Thermocouples
-
A thermoelectric device for measuring temperature, consisting of two wires of different metals connected at two points, a voltage being developed between the two junctions in proportion to the temperature difference.
-
Product
Acoustic Noise Generator
ANG-2200
-
The ANG-2200 Acoustic Noise Generator creates a perimeter of noise that defeats acoustic leakage eavesdropping devices including wired microphones inside walls, contact microphones, audio transmitters located in AC outlets, and laser/microwave reflections from windows.
-
Product
Cable Assembly, 25-Pin D-Type, Female to Unterminated With Cut Ends, 2m
A025DF4-C-0A200
-
The 25-Pin Connector to Unterminated Cable Assy is constructed from PFA insulated 19/0.18 (21AWG) Tinned Copper wire. The connector can be secured to the product by screwlocks. The unterminated connections are coded to match the connector pin designation. Please ensure appropriate electrical safety precautions are observed when using this product.
-
Product
Portable Tester
ECAD System 2002
-
The ECAD System 2002 is a portable, ruggedized tester that can be used for troubleshooting and condition monitoring of installed circuits, cables and wiring harness. The ECAD tester is a combination of traditional electrical measurements, a database for storing test results, and data analysis software. This powerful combination allows a user to evaluate the condition of all circuit components in a logical and straightforward manner from one end of the circuit.
-
Product
CAN/FlexRay/Differential Bus PXI Fault Insertion Switch - 8 Channel
40-200-008
-
This PXI Fault Insertion module is designed to simulate common faults on two wire communication interfaces such as CAN Bus. This module supports 4 or 8-channels of two wire serial interfaces. Each channel can simulate an open fault in either or both wires, a short between both wires or a short to one of eight externally applied fault connections, such as a battery connection or ground, via four fault buses. Each channel can support up to 0.3A and is rated to handle up to 100V between the wire pairs. The wire pairs have controlled transmission line impedance suited to most differential pair signalling systems, including fast CAN Bus interfaces and RS232. Each fault bus is capable of carrying 2A allowing multiple channels to be connected to the same fault condition. Additionally, each fault bus features a changeover relay to allow the user to connect alternative fault conditions to the fault buses.
-
Product
RF/Microwave Assembly Capability
-
Teledyne Labtech offers a comprehensive build-to-print microwave module and microwave components manufacturing service. This includes MMIC placement, Au wire bonding, SMT assembly and test.Our microwave MIC production facility is housed in a class 10,000 clean room that accommodates manual chip placement and semi-automatic wire bond assembly. Dedicated microwave components manufacturing is undertaken within production cells established to meet specific customer or product requirements.
-
Product
Downloading Multifunction Tester
ET4500
-
The new ET4500 tester carries out all the tests needed to verify the safety of electrical installations in domestic, commercial and industrial wiring installations in accordance with the latest regulations.
can be used to carry out 3 wire earth testing and has on board memory to store and download all installation test results for documentation.
Everything about the new ET Series has been designed to save time and make testing easier.Fast, reliable high current and non-trip loop testing comes as standard together with a high level of input protection and a CAT IV safety rating .Supplied with a full range of accessories.
-
Product
Eurocard Plugbord
E220-6U-1
-
VECTOR Electronics and Technology, Inc.
6U x 220mm Eurocard size for 96-pin DIN connectors. Pad-Per-Hole both sides. Voltage and ground buses around board perimeter on both sides. Pad and bus surfaces solder coated for user convenience.For solder, Wire-Wrap or mixed wiring methods. Row and column legends provided.
-
Product
Energy Analyzer
EP600i
-
The EnergyPro EP600i is portable and easy to use. Perfect for single phase or three phase energy consumption analysis and basic power quality monitoring. It supports standard wiring configurations and comes with a set of 1A - 2500A WideRangeFlexCT ™. The graphics display makes setup very easy and intuitive - you can setup and record data without looking at the manual!
-
Product
Circuit Breaker Finder
6504
-
Peaceful Thriving Enterprise Co Ltd
Circuit Breaker Finder is a multi-function circuit tracer/ identifier. Circuit Breaker Finder identifies circuit breakers without interrupting service.This device is formed by 1x Transmitter and 1x Receiver. There are 3 functions: (1) Socket Tester (Wire Mapping)(2) Circuit Tracing / Identifying(3) Non-Contact Voltage Detecting
-
Product
Ultrasonic Transducer
-
F&K Physiktechnik offers ultrasonic transducers "Made in Germany" for all kinds of bond applications. The complete range includes fine wire wedge transducers, fine wire ball transducers as well as heavy wire transducers.
-
Product
PXI-8513 , 2-Port, Software-Selectable PXI CAN Interface Module
780688-02
-
2-Port, Software-Selectable PXI CAN Interface Module—The PXI‑8513 is a software-selectable Controller Area Network (CAN) interface for developing applications with the NI‑XNET driver. NI‑XNET Software‑Selectable CAN Interfaces offer the best flexibility for CAN development with onboard transceivers for High-Speed/Flexible Data‑rate, Low-Speed/Fault Tolerant Single Wire CAN as well as any external transceiver. The PXI‑8513 excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals, such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The NI‑XNET device-driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts.
-
Product
SQUID Series Arrays
-
The SQUID series arrays are ideal for readout of TES sensors or as amplifier stage for discrete two-stage applications. Integrated bias resistors for TES or two-stage applications reduce wiring complexity. Various arrays with input inductances of 3 to 6 nH, input sensitivities of 17 to 23 µA/Phi0, and a current noise between 5 and 10 pA/sqrt(Hz) @ 4 K are available.
-
Product
Switch Modules - 16 Single Pole, Form C, Discrete Relays which are Wired & Controlled Individually
JX16/KC
-
This module has 16 single pole, Form C, discrete relays which are wired and controlled individually. The relays can be externally wired to make any configuration needed. Use as individual A-B relays or use them to drive external relays, solinoids, or any external device. It is available with Type S or M reed relays.
-
Product
Solid State Active Synchro Control Differential Transmitter
-
Computer Conversions Corporation
The input is transformer isolated and accuracy applies over the operating temperature range and with +/-10% input amplitude and frequency variations. The operational amplifier outputs are not transformer isolated, and can be driven into external power amplifiers and Scott "T" transformers for 3 wire synchro outputs. A typical application of this series is in a conventional positioning servo system as a complex error processor. The use of the solid state CDX makes possible the design of servo systems that can be digitally programmed by direct computer input to the digital input of the SCDX.
-
Product
Cable 96-Pin Female To 100-Pin Male Micro-D, 0.5m
40-973C-096-0.5M-FM
-
The 96-Pin to 100-Pin SCSI Style Micro-D Adaptor Lead is constructed from 7/36 (28AWG) Tinned Copper twisted pair wiring with Polyolefin insulation to minimise crosstalk. Metal Spring Latches are provided on the 96-Pin connector and 4-40 UNC screwlocks on the 100-Pin connector.
-
Product
4-Wire Resistance Measurement | Continuity & HiPot Cable & Wire Harness Testers
-
An add-on option for the CableEye HVX high voltage cable tester series that permits expanded testing for contact and wire resistance as low as 1 mΩ. After checking for opens, shorts, miswires, and resistance limits, the 4-wire Kelvin measurement applies a user-selectable test current from 10 mA to 1 A to determine connection resistance within 1 mΩ. The resistance profile of a model cable may be stored and used as a basis of comparison during later testing to reveal cold solder joints, faulty crimps, recessed pins, pin contact contamination, improper wire gauge, and stress-extruded wire.This option may be purchased with any new HVX tester, or added as an upgrade to any of your existing HVX testers.
-
Product
Photo Detector with Integrated Transimpedance Amplifiers
ADN3010-11
-
Analog Devices optoelectronic amplifiers include a range of germanium photodiodes that, through a proprietary process, have been monolithically integrated with silicon transimpedance amplifiers and limiting amplifiers. This process eliminates the need for bond wires connecting the photodiode to the transimpedance amplifier, which leads to improved performance and greater manufacturing reliability. Our portfolio of products also supports the growing need for optical and electrical interface miniaturization.
-
Product
Enclosure, G12, Front Mount, 4 Cable Clamps, 12" Depth
410112739
-
Enclosure, G12, Front Mount, 4 Cable Clamps, 12" Depth Includes hinged cover and 4 cable clamps for discrete wiring that provide secure strain relief. With cable clamps in open position- stiffener bar can be removed allowing installation or removal of cables without unplugging patchcords from assembly. Housing: Material = .06" Aluminum, Finish = Powder Coat BlackCover(s)/Access Panel(s): Material = .12" Aluminum, Finish = Black Anodize
-
Product
HDMI Cable Tester
MT-7062
-
Test all HDMI cables with Type A to A, A to C and C to C connectorsDesign with loopback function allows test HDMI type A to A, A to C on main unit.Automatically fast & slow scan for testing all conductors status in a cable, Manual test for step by step detecting individual conductors for intermittent faults.Automatically detect wiring on HDMI type A or type C condition in straight, short, open, crossover in all RGB conductors.Quickly troubleshoot and verify HDTV installation and DIY termination in the field.
-
-
Product
Connector, Cable Mount, 25 Pin 1.27mm Pitch Micro-D, Female, Crimp Pin
C025CFR-1CP-0A
-
This 25 pin micro-D connector is designed to allow users to directly terminate with crimped connections and is suitable for 26 AWG copper wire. Screwlocks are provided to secure the connector to its associated product. This connector is suitable for high density applications including connection to Pickering's LXI DIO/Trigger port.
-
Product
Pull-Thru Adapter, Wired, QuadraPaddle, f/ Pickering 40-614A-002
510140253
-
Pull-Thru Adapter, Wired, QuadraPaddle, f/ Pickering 40-614A-002.
-
Product
Chassis - Built as 60 or 75 ohm Matrix Configuration Switch Modules for High Bandpass
CXG Matrix
-
These Chassis are built as 50 or 75 ohm matrix configurations of 4x8 or 8x8 using tree switch configuration switch modules for high bandpass. The internal matrix block is wired out to BNC, SMA or other 50 or 75 ohm connectors. LEDs on the front panel show switch and power status. Add a Control Module to complete the system.
