-
Product
PXI Prototyping Module, 1-Slot, 37-Pin D-Type
40-225A-201
-
The 40-225A PXI Prototyping Modules are stripped down versions of the 40-220A PXI Breadboard series. These are very basic, low cost prototype modules. They have no PXI interface but do have access to fused power supplies from the PXI backplane.
-
Product
DIN Eurocard Plugbord
-
VECTOR Electronics and Technology, Inc.
Boards for 96 and 160-pin DIN Eurocard plug-in application with option to mount DIN 41612 type connectors on ends. Available with different circuit patterns for prototyping applications.
-
Product
COM Express
-
The COM Express product platform includes Intel©-based CPU modules and Type 2/3 or Type 6 carrier cards. Additionally, support products are available for prototyping and production such as: development systems, MIL-DTL-38999 front panels, and an assortment of cables.
-
Product
PXI, CPCI Development And Prototyping Board
TE2100
-
Team Solutionsí PXI Development and Prototype board is the fastest road for system integrators to deliver a PXI customized product and provides design engineers with a speedy avenue to release PXI based prototypes and products.
-
Product
sbRIO-9866, Non-Enclosed, 1-Port C Series LIN Interface Module
785965-01
-
Non-Enclosed, 1-Port C Series LIN Interface Module—The sbRIO‑9866 is a Local Interconnect Network (LIN) interface for developing applications with the NI‑XNET driver. The sbRIO‑9866 excels in applications requiring real-time, high-speed manipulation of hundreds of LIN frames and signals such as hardware‑in‑the‑loop (HIL) simulation, rapid control prototyping, bus monitoring, automation control, and more. You can perform this manipulation while taking other DAQ measurements in the same CompactDAQ hardware platform or while performing low-level FPGA control and embedded monitoring in the same CompactRIO Chassis. Non-enclosed modules are designed for OEM applications.
-
Product
Design for Test
-
Test Coach offers Design for Test (DFT) consulting to assist customers with design review of prototype boards prior to release for production. Design for Test analysis is extremely important in ensuring that an assembly will achieve the highest possible test coverage. For ICT, this DFT will review the board to confirm that the bed-of-nails test fixture can be fabricated to test an assembly without sacrificing test coverage. As with ICT, Flying Probe benefits from DFT analysis by reviewing test point access and mechanical challenges that may affect the potential test coverage. Completing a DFT enables Test Coach to make recommendations to our customers that may be implemented on boards during the design phase which will allow for the most comprehensive coverage at time of test.
-
Product
Ettus USRP X410, 1 MHz to 7.2 GHz, 400 MHz Bandwidth, GPS-Disciplined OCXO, USRP Software Defined Radio Device
787272-01
-
The Ettus USRP X410 integrates hardware and software to help you prototype high-performance wireless systems and perform over-the-air signal generation and analysis. Additionally, the Ettus USRP X410 features a two-stage superheterodyne architecture with four independent transmitter and receiver channels. It also features a Xilinx Zynq Ultrascale+ RFSoC with programmable FPGA supporting the Open Source UHD tool flow as well as LabVIEW FPGA. With these features, the Ettus USRP X410 has the RF and processing performance for applications such as wireless communications prototyping, spectrum monitoring, and signals intelligence. The Ettus USRP X410 is equipped with a GPS-disciplined 10 MHz oven-controlled crystal oscillator (OCXO) Reference Clock, which improves frequency accuracy and synchronization.
-
Product
Antenna Test Facility
-
Raytheon’s Antenna Test Facility (ATF) provides state-of-the-art measurement capabilities to assist in the development of advanced antenna technologies for a variety of airborne and space applications such as advanced radar and communication systems. The ATF is available for use by Raytheon businesses as well as other companies that design and prototype new and experimental antennas.
-
Product
Bench Top Humidity Environmental Chamber
-
Burnsco Environmental Test Chambers
Our compact bench top chamber is ideal for prototype testing, life testing, and quality and durability testing. Its small footprint and comparatively large volume make it ideal in labs where space is a premium.
-
Product
Flying Probe Tester
Condor MTS 505
-
Primarily the Flying Probe Tester was developed to enable In-Circuit testing (ICT) of prototype PCBs. For testing a new design an existing fixture has to be changed or a new fixture has to be procured. The fixtureless design of the MTS 505 Condor is one of its most attractive properties, where the unnecessary and costly time delays incurred for fixture build or changes can be avoided. It is the ideal platform for testing prototypes.
-
Product
Decade Box, Calibrated, Capacitance, 5, 100pF to 11111µF, 5 %
72-7265 CAL
-
The 72-7265 CAL from Tenma is a capacitance decade box. It is ideal for service, prototype and experimental use. This useful tool may be set at any non polarized capacitor value from 100pF to 11,111µF in 100pF increments. The decade accuracy is ±5% capacitors used throughout at <1μF, 1KHz test frequency, ≥1μF, 100Hz test frequency. It has weight of 304g/0.69lb and dimension is 14.7cm × 11.7cm × 5.5cm (5.79" × 4.61" × 2.16"). It is typically used in general applications, troubleshooting, maintenance, education and vocational training, production line testing, radio and TV services, working standards, research design & develop, physics laboratory work.
-
Product
Chassis & Subsystem Pre-integration
-
Mercury’s broad ecosystem of compute building blocks enable SWaP-efficient solutions to be quickly configured within a low-risk environment. Our off-the-the-shelf chassis facilitate rapid development work and prototyping to support concurrent engineering initiatives.
-
Product
Thermal Testing And Analysis
-
Response Dynamics Vibration Engineering, Inc.
We have consulted on thermal issues ranging from conduction issues in TECs, thermal radiation modeling, and countless air cooled system issues relating to system performance, vibration, and acoustics noise. We use a wide array of thermocouple instrumentation, thermal imaging, flow measurements, as well as finite element analysis and analytic modeling to measure, design, and debug thermal and related issues. We often work on customer products in our Response Dynamics lab where we characterize the system, engineer solution options, and prototype solutions. We then work with the customer to work the winning solution into their quality control and manufacturing process.
-
Product
HIL and RCP DFIG Laboratory
-
This laboratory combines the best of both OPAL-RT and Festo solutions to deliver academic researchers and teachers with the ideal Hardware-in-the-Loop (HIL) and Rapid Control Prototyping (RCP) simulation system to conduct experiments and teach in the fields of electrical machinery, power converters and wind energy generation.
-
Product
PLTS Measurement And Calibration
N19303B
-
The new Physical Layer Test System (PLTS) 2024 is the industry standard for signal integrity measurements and data post‑processing high-speed interconnects, such as cables, backplanes, PCBs, and connectors. Signal integrity laboratories worldwide have benefited from the power of PLTS in the R&D prototype test phase.
-
Product
*C Series CAN Interface Module
-
C Series CAN Interface Modules communicate using onboard transceivers for High-Speed/Flexible Data‑Rate or Low-Speed/Fault Tolerant CAN. C Series CAN Interface Modules are either compatible with NI-XNET or the NI-985x driver, depending on model.Using NI-XNET, you can create applications that require real-time, high-speed manipulation of hundreds of CAN frames and signals. The NI-XNET device-driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time. C Series CAN Interface Modules work well in applications such as hardware-in-the-loop (HIL) simulation, rapid control prototyping, bus monitoring, and automation control.
-
Product
Software Development Projects
-
Precision Development Consulting Inc
Automation of new process tool prototype in startup environment, Complex R&D Gasbox Automation, Semiconductor System Control Software, Wafer Transfer Control Software, 300mm Factory Automation, Complete port of Spectrometer software to windows, HSMS Protocol
-
Product
PCIe-5775, 12-Bit, 6.4 GS/s, 2-Channel PCI FlexRIO Digitizer Device
785595-01
-
The PCIe-5775 is a PCI FlexRIO Digitizer Device that provides 6 GHz of AC-coupled analog bandwidth and 12 bits of resolution. You can operate the PCIe-5775 in a dual-channel mode at 3.2 GS/s or in a single-channel interleaved mode at 6.4 GS/s. With a passband from 1 MHz to more than 6 GHz, the PCIe-5775 is ideal for high-bandwidth frequency domain applications, including radar prototyping, LIDAR, and communications.
-
Product
PXI-8511, 1‑ or 2-Port, Low-Speed/Fault Tolerant PXI CAN Interface Module
780686-02
-
1‑ or 2-Port, Low-Speed/Fault Tolerant PXI CAN Interface Module—The PXI‑8511 is a fault-tolerant Controller Area Network (CAN) interface for developing applications with the NI‑XNET driver. The PXI‑8511 excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals, such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The NI‑XNET device-driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimize message latency and freeing host processor time for processing complex models and applications.
-
Product
Multi-Domain Simulation
-
Every product engineering team deals with questions in the virtual prototyping phase, many of these covering multiple engineering domains. ESI's Visual-Environment multi-domain modelling allows these teams to work together in a single user environment, around a single core compute model. This multi-domain simulation environment has the capacity to integrate all virtual prototyping problems across CAE domains. In addition, its user-friendly interface and automation features empower engineering teams to be ever more productive!
-
Product
PXI Prototyping and Breadboard Modules
-
The breadboard modules with digital I/O (the 40-220A series) allow the user to construct their own circuit in situations where a PXI module is not available. For example when it is required to integrate a non-switching function into a PXI chassis. Typical applications include creating custom circuitry that can be housed on a 3U board or to build special “one-off” switching modules.
-
Product
X-Ray Inspection
-
X-ray inspection systems are used wherever defects need to be detected by non-destructive means. The spectrum of use is broad and ranges from quality controls for complex assemblies, to the testing of materials for cracks and air inclusions, to foreign matter inclusions and shape deviations. The trend toward miniaturization, higher packing densities, and the relocation of components to the interior of the assembly require precise X-ray inspections that detect hidden defects quickly and reliably. X-ray systems from Viscom are used for the inspection of series assemblies as well as sampling and prototype controls. They take care of typical inspection tasks in concealed areas such as void controls, THT filling level measurements, and HIP inspections. At the same time, the systems reliably determine defect features such as coplanarity and polarity – at high inspection speeds and in a cost-effective way.
-
Product
Engineering
-
As a pioneer in infrared imaging solutions, our engineers have an unsurpassed level of proficiency in prototype design, customization and system integration. Our expertise is multifaceted ranging from advanced infrared sensor signal processing, calibration techniques, radiometry, optics, embedded software development, PC application software development, industrial and mechanical design and production tooling. Our goal is your successful project; one that utilizes the correct components and is completed on time and within budget. This is accomplished through our Concept to Solution approach which allows for the use of technically advanced components, group collaboration, quick responses and final products tested to spec. Whatever level of integration you choose and support you need, know our engineering team is there to assist.
-
Product
PXIe-5764, 16-Bit, 1 GS/s, 4-Channel PXI FlexRIO Digitizer
785171-01
-
The PXIe-5764 is a PXI FlexRIO Digitizer that simultaneously samples four channels at 1 GS/s with 16 bits of resolution and features 400 MHz of analog input bandwidth. With up to 70 dB of SNR, the PXIe-5764 is ideal for applications that require a wide dynamic range with a wideband digitizer. The FlexRIO driver includes support for finite and continuous streaming modes, and you can implement custom algorithms and real-time signal processing on the LabVIEW-programmable Xilinx Kintex UltraScale FPGA. Available in AC and DC coupled variants, the PXIe-5764 is ideal for both time and frequency domain applications, including radar prototyping, LIDAR, communications, microscopy, OCT, event detection, and particle physics.
-
Product
Project Management
-
Precision Development Consulting Inc
Process Chamber Development, PVD Gun Prototype, Prototype Batch CVD Tool, Fifty-wafer Enhancement to Batch Tool, Manufacturing Equipment Process, Test Systems for Missile components
-
Product
mmWave Transceiver System
-
The mmWave Transceiver System is a modular hardware solution for prototyping real-time communications systems for mmWave frequencies. With 2 GHz of bandwidth, the system can be used to evaluate the ultrawide bandwidth signals being proposed for next-generation wireless communications standards in real time. You can analyze these ultrawide bandwidth signals in real time using a multi-FPGA architecture for computationally intensive digital signal processing. With this processing capability, you can build a real-time two-way communications link with up to 2 GHz of bandwidth.
-
Product
Test Equipment
-
Southern Photonics designed and manufactured all the test equipment currently being manufactured by Coherent Solutions, as well as equipment for non-telecoms applications. This includes FBG strain interrogators, optical pulse phase analysers, OSNR meters, optical power meters, optical spectrum analysers, optical gas sensors… you get the idea. All test equipment we build is robust and easy to use. The picture shows some of what we can do – anything from prototype benchtop test gear (as in the combination ASE source and laser combiner on top of the stack) to field test equipment (the portable fast OSA on the bottom).
-
Product
HES Prototyping Boards
-
HES™ is a feature-rich family of SoC/ASIC pre-silicon physical prototyping and hardware emulation boards. The family features boards with high-performance devices from either Xilinx (including Virtex-7, Virtex UltraScale, Virtex UltraScale+ and Zynq UltraScale+) or Microchip (PolarFire and SmartFusion2).
-
Product
Product Safety Testing
-
NCEE Labs is an A2LA Accredited product safety compliance testing lab. We specialize in compliance testing to US and harmonized international standards. NCEE Labs also offers NRTL testing services. With experienced product safety engineers, we provide expert assistance, whether evaluating early prototypes or assisting with aftermarket design changes.
-
Product
Mechanical Fixtures Available w/ESD Plates & ESD Pressure Pins
-
H+W Test Products has developed a series of inexpensive mechanical test fixtures. These fixtures are designed for testing low volume runs of printed circuit boards or prototype applications requiring approximately 150 test points.
